Abstract: Martensitic stainless steels have been extensively used for their good corrosion resistance and better mechanical properties. Heat treatment was suggested as one of the most excellent ways to this regard; hence, it affects the microstructure, mechanical and corrosion properties of the steel. In the current research work the microstructural changes and corrosion behavior in an AISI 420A stainless steel exposed to temperatures in the 980-1035oC range were investigated. The heat treatment is carried out in vacuum furnace within the said temperature range. The quenching of the samples was carried out in oil, brine and water media. The formation and stability of passive film was studied by Open Circuit Potential, Potentiodynamic polarization and Electrochemical Scratch Tests. The Electrochemical Impedance Spectroscopy results simulated with Equivalent Electrical Circuit suggested bilayer structure of outer porous and inner barrier oxide films. The quantitative data showed thick inner barrier oxide film retarded electrochemical reactions. Micrographs of the quenched samples showed sigma and chromium carbide phases which prove the corrosion resistance of steel alloy.
Abstract: The Random Coefficient Dynamic Regression (RCDR)
model is to developed from Random Coefficient Autoregressive
(RCA) model and Autoregressive (AR) model. The RCDR model
is considered by adding exogenous variables to RCA model. In this
paper, the concept of the Maximum Likelihood (ML) method is used
to estimate the parameter of RCDR(1,1) model. Simulation results
have shown the AIC and BIC criterion to compare the performance of
the the RCDR(1,1) model. The variables as the stationary and weakly
stationary data are good estimates where the exogenous variables
are weakly stationary. However, the model selection indicated that
variables are nonstationarity data based on the stationary data of the
exogenous variables.
Abstract: The importance of nurturing, accumulating, and efficiently deploying knowledge resources through formal structures and organisational mechanisms is well understood. Recent trends in knowledge management (KM) highlight that the effective creation and transfer of knowledge can also rely upon extra-organisational channels, such as, informal networks. The perception exists that the role of informal networks in knowledge creation and performance has been underestimated in the organisational context. Literature indicates that many managers fail to comprehend and successfully exploit the potential role of informal networks to create value for their organisations. This paper investigates: 1) whether managers share work-specific knowledge with informal contacts within and outside organisational boundaries; and 2) what do they think is the importance of this knowledge collaboration in their learning and work outcomes.
Abstract: Support Vector Machine (SVM) is a recent class of statistical classification and regression techniques playing an increasing role in applications to detection problems in various engineering problems, notably in statistical signal processing, pattern recognition, image analysis, and communication systems. In this paper, SVM is applied to an infrared (IR) binary communication system with different types of channel models including Ricean multipath fading and partially developed scattering channel with additive white Gaussian noise (AWGN) at the receiver. The structure and performance of SVM in terms of the bit error rate (BER) metric is derived and simulated for these channel stochastic models and the computational complexity of the implementation, in terms of average computational time per bit, is also presented. The performance of SVM is then compared to classical binary signal maximum likelihood detection using a matched filter driven by On-Off keying (OOK) modulation. We found that the performance of SVM is superior to that of the traditional optimal detection schemes used in statistical communication, especially for very low signal-to-noise ratio (SNR) ranges. For large SNR, the performance of the SVM is similar to that of the classical detectors. The implication of these results is that SVM can prove very beneficial to IR communication systems that notoriously suffer from low SNR at the cost of increased computational complexity.
Abstract: The presence of harmonic in power system is a major
concerned to power engineers for many years. With the increasing
usage of nonlinear loads in power systems, the harmonic pollution
becomes more serious. One of the widely used computation
algorithm for harmonic analysis is fast Fourier transform (FFT). In
this paper, a harmonic analyzer using FFT was implemented on
TMS320C6713 DSK. The supply voltage of 240 V 59 Hz is stepped
down to 5V using a voltage divider in order to match the power
rating of the DSK input. The output from the DSK was displayed on
oscilloscope and Code Composer Studio™ software. This work has
demonstrated the possibility of analyzing the 240V power supply
harmonic content using the DSK board.
Abstract: Nowadays, people are going more and more mobile, both in terms of devices and associated applications. Moreover, services that these devices are offering are getting wider and much more complex. Even though actual handheld devices have considerable computing power, their contexts of utilization are different. These contexts are affected by the availability of connection, high latency of wireless networks, battery life, size of the screen, on-screen or hard keyboard, etc. Consequently, development of mobile applications and their associated mobile Web services, if any, should follow a concise methodology so they will provide a high Quality of Service. The aim of this paper is to highlight and discuss main issues to consider when developing mobile applications and mobile Web services and then propose a framework that leads developers through different steps and modules toward development of efficient and secure mobile applications. First, different challenges in developing such applications are elicited and deeply discussed. Second, a development framework is presented with different modules addressing each of these challenges. Third, the paper presents an example of a mobile application, Eivom Cinema Guide, which benefits from following our development framework.
Abstract: This work presents a matched field processing (MFP)
algorithm based on Dopplerlet transform for estimating the motion
parameters of a sound source moving along a straight line and with a
constant speed by using a piecewise strategy, which can significantly
reduce the computational burden. Monte Carlo simulation results and
an experimental result are presented to verify the effectiveness of the
algorithm advocated.
Abstract: Society has grown to rely on Internet services, and the
number of Internet users increases every day. As more and more
users become connected to the network, the window of opportunity
for malicious users to do their damage becomes very great and
lucrative. The objective of this paper is to incorporate different
techniques into classier system to detect and classify intrusion from
normal network packet. Among several techniques, Steady State
Genetic-based Machine Leaning Algorithm (SSGBML) will be used
to detect intrusions. Where Steady State Genetic Algorithm (SSGA),
Simple Genetic Algorithm (SGA), Modified Genetic Algorithm and
Zeroth Level Classifier system are investigated in this research.
SSGA is used as a discovery mechanism instead of SGA. SGA
replaces all old rules with new produced rule preventing old good
rules from participating in the next rule generation. Zeroth Level
Classifier System is used to play the role of detector by matching
incoming environment message with classifiers to determine whether
the current message is normal or intrusion and receiving feedback
from environment. Finally, in order to attain the best results,
Modified SSGA will enhance our discovery engine by using Fuzzy
Logic to optimize crossover and mutation probability. The
experiments and evaluations of the proposed method were performed
with the KDD 99 intrusion detection dataset.
Abstract: The increasing complexity of software development based on peer to peer networks makes necessary the creation of new frameworks in order to simplify the developer-s task. Additionally, some applications, e.g. fire detection or security alarms may require real-time constraints and the high level definition of these features eases the application development. In this paper, a service model based on a component model with real-time features is proposed. The high-level model will abstract developers from implementation tasks, such as discovery, communication, security or real-time requirements. The model is oriented to deploy services on small mobile devices, such as sensors, mobile phones and PDAs, where the computation is light-weight. Services can be composed among them by means of the port concept to form complex ad-hoc systems and their implementation is carried out using a component language called UM-RTCOM. In order to apply our proposals a fire detection application is described.
Abstract: The Bangalore City is facing the acute problem of
pollution in the atmosphere due to the heavy increase in the traffic
and developmental activities in recent years. The present study is an
attempt in the direction to assess trend of the ambient air quality
status of three stations, viz., AMCO Batteries Factory, Mysore Road,
GRAPHITE INDIA FACTORY, KHB Industrial Area, Whitefield
and Ananda Rao Circle, Gandhinagar with respect to some of the
major criteria pollutants such as Total Suspended particular matter
(SPM), Oxides of nitrogen (NOx), and Oxides of sulphur (SO2). The
sites are representative of various kinds of growths viz., commercial,
residential and industrial, prevailing in Bangalore, which are
contributing to air pollution. The concentration of Sulphur Dioxide
(SO2) at all locations showed a falling trend due to use of refined
petrol and diesel in the recent years. The concentration of Oxides of
nitrogen (NOx) showed an increasing trend but was within the
permissible limits. The concentration of the Suspended particular
matter (SPM) showed the mixed trend. The correlation between
model and observed values is found to vary from 0.4 to 0.7 for SO2,
0.45 to 0.65 for NOx and 0.4 to 0.6 for SPM. About 80% of data is
observed to fall within the error band of ±50%. Forecast test for the
best fit models showed the same trend as actual values in most of the
cases. However, the deviation observed in few cases could be
attributed to change in quality of petro products, increase in the
volume of traffic, introduction of LPG as fuel in many types of
automobiles, poor condition of roads, prevailing meteorological
conditions, etc.
Abstract: In working mode some unexpected changes could
be arise in inner structure of electromagnetic device. They
influence modification in electromagnetic field propagation map.
The field values at an observed boundary are also changed. The
development of the process has to be watched because the arising
structural changes would provoke the device to be gone out later.
The probabilistic assessment of the state is possible to be made.
The numerical assessment points if the resulting changes have
only accidental character or they are due to the essential inner
structural disturbances.
The presented application example is referring to the 200MW
turbine-generator. A part of the stator core end teeth zone is
simulated broken. Quasi three-dimensional electromagnetic and
temperature field are solved applying FEM. The stator core state
diagnosis is proposed to be solved as an identification problem on
the basis of a statistical criterion.
Abstract: Mobile IPv6 (MIPv6) describes how mobile node can change its point of attachment from one access router to another. As a demand for wireless mobile devices increases, many enhancements for macro-mobility (inter-domain) protocols have been proposed, designed and implemented in Mobile IPv6. Hierarchical Mobile IPv6 (HMIPv6) is one of them that is designed to reduce the amount of signaling required and to improve handover speed for mobile connections. This is achieved by introducing a new network entity called Mobility Anchor Point (MAP). This report presents a comparative study of the Hierarchical Mobility IPv6 and Mobile IPv6 protocols and we have narrowed down the scope to micro-mobility (intra-domain). The architecture and operation of each protocol is studied and they are evaluated based on the Quality of Service (QoS) parameter; handover latency. The simulation was carried out by using the Network Simulator-2. The outcome from this simulation has been discussed. From the results, it shows that, HMIPv6 performs best under intra-domain mobility compared to MIPv6. The MIPv6 suffers large handover latency. As enhancement we proposed to HMIPv6 to locate the MAP to be in the middle of the domain with respect to all Access Routers. That gives approximately same distance between MAP and Mobile Node (MN) regardless of the new location of MN, and possible shorter distance. This will reduce the delay since the distance is shorter. As a future work performance analysis is to be carried for the proposed HMIPv6 and compared to HMIPv6.
Abstract: A new robust nonlinear control scheme of a manipulator is proposed in this paper which is robust against modeling errors and unknown disturbances. It is based on the principle of variable structure control, with sliding mode control (SMC) method. The variable structure control method is a robust method that appears to be well suited for robotic manipulators because it requers only bounds on the robotic arm parameters. But there is no single systematic procedure that is guaranteed to produce a suitable control law. Also, to reduce chattring of the control signal, we replaced the sgn function in the control law by a continuous approximation such as tangant function. We can compute the maximum load with regard to applied torque into joints. The effectivness of the proposed approach has been evaluated analitically demonstrated through computer simulations for the cases of variable load and robot arm parameters.
Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: The paper considers a single-server queue with fixedsize
batch Poisson arrivals and exponential service times, a model
that is useful for a buffer that accepts messages arriving as fixed size
batches of packets and releases them one packet at time. Transient
performance measures for queues have long been recognized as
being complementary to the steady-state analysis. The focus of the
paper is on the use of the functions that arise in the analysis of the
transient behaviour of the queuing system. The paper exploits
practical modelling to obtain a solution to the integral equation
encountered in the analysis. Results obtained indicate that under
heavy load conditions, there is significant disparity in the statistics
between the transient and steady state values.
Abstract: Laboratory activities have produced benefits in
student learning. With current drives of new technology resources
and evolving era of education methods, renewal status of learning
and teaching in laboratory methods are in progress, for both learners
and the educators. To enhance learning outcomes in laboratory works
particularly in engineering practices and testing, learning via handson
by instruction may not sufficient. This paper describes and
compares techniques and implementation of traditional (expository)
with open-ended laboratory (problem-based) for two consecutive
cohorts studying environmental laboratory course in civil engineering
program. The transition of traditional to problem-based findings and
effect were investigated in terms of course assessment student
feedback survey, course outcome learning measurement and student
performance grades. It was proved that students have demonstrated
better performance in their grades and 12% increase in the course
outcome (CO) in problem-based open-ended laboratory style than
traditional method; although in perception, students has responded
less favorable in their feedback.
Abstract: This paper offers a case study, in which
methodological aspects of cell design for transformation the
production process are applied. The cell redesign in this work is
tightly focused to reach optimization of material flows under real
manufacturing conditions. Accordingly, more individual techniques
were aggregated into compact methodical procedure with aim to built
one-piece flow production. Case study was concentrated on relatively
typical situation of transformation from batch production to cellular
manufacturing.
Abstract: The speech signal conveys information about the
identity of the speaker. The area of speaker identification is
concerned with extracting the identity of the person speaking the
utterance. As speech interaction with computers becomes more
pervasive in activities such as the telephone, financial transactions
and information retrieval from speech databases, the utility of
automatically identifying a speaker is based solely on vocal
characteristic. This paper emphasizes on text dependent speaker
identification, which deals with detecting a particular speaker from a
known population. The system prompts the user to provide speech
utterance. System identifies the user by comparing the codebook of
speech utterance with those of the stored in the database and lists,
which contain the most likely speakers, could have given that speech
utterance. The speech signal is recorded for N speakers further the
features are extracted. Feature extraction is done by means of LPC
coefficients, calculating AMDF, and DFT. The neural network is
trained by applying these features as input parameters. The features
are stored in templates for further comparison. The features for the
speaker who has to be identified are extracted and compared with the
stored templates using Back Propogation Algorithm. Here, the
trained network corresponds to the output; the input is the extracted
features of the speaker to be identified. The network does the weight
adjustment and the best match is found to identify the speaker. The
number of epochs required to get the target decides the network
performance.
Abstract: Wheat gluten hydrolyzates (WGHs) and anchovy fine
powder hydrolyzates (AFPHs) were produced at 300 MPa using
combinations of Flavourzyme 500MG (F), Alcalase 2.4L (A),
Marugoto E (M) and Protamex (P), and then were compared to those
produced at ambient pressure concerning the contents of soluble solid
(SS), soluble nitrogen and electrophoretic profiles. The contents of SS
in the WGHs and AFPHs increased up to 87.2% according to the
increase in enzyme number both at high and ambient pressure. Based
on SS content, the optimum enzyme combinations for one-, two-,
three- and four-enzyme hydrolysis were determined as F, FA, FAM
and FAMP, respectively. Similar trends were found for the contents of
total soluble nitrogen (TSN) and TCA-soluble nitrogen (TCASN). The
contents of SS, TSN and TCASN in the hydrolyzates together with
electrophoretic mobility maps indicates that the high-pressure
treatment of this study accelerated protein hydrolysis compared to
ambient-pressure treatment.
Abstract: The goal of this project is to design a system to
recognition voice commands. Most of voice recognition systems
contain two main modules as follow “feature extraction" and “feature
matching". In this project, MFCC algorithm is used to simulate
feature extraction module. Using this algorithm, the cepstral
coefficients are calculated on mel frequency scale. VQ (vector
quantization) method will be used for reduction of amount of data to
decrease computation time. In the feature matching stage Euclidean
distance is applied as similarity criterion. Because of high accuracy
of used algorithms, the accuracy of this voice command system is
high. Using these algorithms, by at least 5 times repetition for each
command, in a single training session, and then twice in each testing
session zero error rate in recognition of commands is achieved.