Abstract: The sintering step in powder metallurgy (P/M) processes is very sensitive as it determines to a large extent the properties of the final component produced. Spark plasma sintering over the past decade has been extensively used in consolidating a wide range of materials including metallic alloy powders. This novel, non-conventional sintering method has proven to be advantageous offering full densification of materials, high heating rates, low sintering temperatures, and short sintering cycles over conventional sintering methods. Ti6Al4V has been adjudged the most widely used α+β alloy due to its impressive mechanical performance in service environments, especially in the aerospace and automobile industries being a light metal alloy with the capacity for fuel efficiency needed in these industries. The P/M route has been a promising method for the fabrication of parts made from Ti6Al4V alloy due to its cost and material loss reductions and the ability to produce near net and intricate shapes. However, the use of this alloy has been largely limited owing to its relatively poor hardness and wear properties. The effect of sintering temperature on the densification, hardness, and wear behaviors of spark plasma sintered Ti6Al4V powders was investigated in this present study. Sintering of the alloy powders was performed in the 650–850°C temperature range at a constant heating rate, applied pressure and holding time of 100°C/min, 50 MPa and 5 min, respectively. Density measurements were carried out according to Archimedes’ principle and microhardness tests were performed on sectioned as-polished surfaces at a load of 100gf and dwell time of 15 s. Dry sliding wear tests were performed at varied sliding loads of 5, 15, 25 and 35 N using the ball-on-disc tribometer configuration with WC as the counterface material. Microstructural characterization of the sintered samples and wear tracks were carried out using SEM and EDX techniques. The density and hardness characteristics of sintered samples increased with increasing sintering temperature. Near full densification (99.6% of the theoretical density) and Vickers’ micro-indentation hardness of 360 HV were attained at 850°C. The coefficient of friction (COF) and wear depth improved significantly with increased sintering temperature under all the loading conditions examined, except at 25 N indicating better mechanical properties at high sintering temperatures. Worn surface analyses showed the wear mechanism was a synergy of adhesive and abrasive wears, although the former was prevalent.
Abstract: A methodology based on wavelets is proposed for the automatic location and delimitation of defects in limestone plates. Natural defects include dark colored spots, crystal zones trapped in the stone, areas of abnormal contrast colors, cracks or fracture lines, and fossil patterns. Although some of these may or may not be considered as defects according to the intended use of the plate, the goal is to pair each stone with a map of defects that can be overlaid on a computer display. These layers of defects constitute a database that will allow the preliminary selection of matching tiles of a particular variety, with specific dimensions, for a requirement of N square meters, to be done on a desktop computer rather than by a two-hour search in the storage park, with human operators manipulating stone plates as large as 3 m x 2 m, weighing about one ton. Accident risks and work times are reduced, with a consequent increase in productivity. The base for the algorithm is wavelet decomposition executed in two instances of the original image, to detect both hypotheses – dark and clear defects. The existence and/or size of these defects are the gauge to classify the quality grade of the stone products. The tuning of parameters that are possible in the framework of the wavelets corresponds to different levels of accuracy in the drawing of the contours and selection of the defects size, which allows for the use of the map of defects to cut a selected stone into tiles with minimum waste, according the dimension of defects allowed.
Abstract: Past earthquakes have shown that seismic events may incur large economic losses in buildings. FEMA P-58 provides engineers a practical tool for the performance seismic assessment of buildings. In this study, FEMA P-58 is applied to two typical Italian pre-1970 reinforced concrete frame buildings, characterized by plain rebars as steel reinforcement and masonry infills and partitions. Given that suitable tools for these buildings are missing in FEMA P- 58, specific fragility curves and loss functions are first developed. Next, building performance is evaluated following a time-based assessment approach. Finally, expected annual losses for the selected buildings are derived and compared with past applications to old RC frame buildings representative of the US building stock.
Abstract: In this paper, we present a fast and efficient mesh coarsening algorithm for 3D triangular meshes. Theis approach can be applied to very complex 3D meshes of arbitrary topology and with millions of vertices. The algorithm is based on the clustering of the input mesh elements, which divides the faces of an input mesh into a given number of clusters for clustering purpose by approximating the Centroidal Voronoi Tessellation of the input mesh. Once a clustering is achieved, it provides us an efficient way to construct uniform tessellations, and therefore leads to good coarsening of polygonal meshes. With proliferation of 3D scanners, this coarsening algorithm is particularly useful for reverse engineering applications of 3D models, which in many cases are dense, non-uniform, irregular and arbitrary topology. Examples demonstrating effectiveness of the new algorithm are also included in the paper.
Abstract: In addition to the fact that mental health bears great significance to a particular individual, it can also be regarded as an organizational, community and societal resource. Within the Szeged Health Promotion Research Group, we conducted mental health surveys on two levels: The inhabitants of a medium-sized Hungarian town and students of a Hungarian university with a relatively big headcount were requested to participate in surveys whose goals were to define local government priorities and organization-level health promotion programmes, respectively. To facilitate professional decision-making, we defined three, pragmatically relevant, groups of the target population: the mentally healthy, the vulnerable and the endangered. In order to determine which group a person actually belongs to, we designed a simple and quick measurement tool, which could even be utilised as a smoothing method, the Mental State Questionnaire validity of the above three categories was verified by analysis of variance against psychological quality of life variables. We demonstrate the pragmatic significance of our method via the analyses of the scores of our two mental health surveys. On town level, during our representative survey in Hódmezővásárhely (N=1839), we found that 38.7% of the participants was mentally healthy, 35.3% was vulnerable, while 16.3% was considered as endangered. We were able to identify groups that were in a dramatic state in terms of mental health. For example, such a group consisted of men aged 45 to 64 with only primary education qualification and the ratios of the mentally healthy, vulnerable and endangered were 4.5, 45.5 and 50%, respectively. It was also astonishing to see to what a little extent qualification prevailed as a protective factor in the case of women. Based on our data, the female group aged 18 to 44 with primary education—of whom 20.3% was mentally healthy, 42.4% vulnerable and 37.3% was endangered—as well as the female group aged 45 to 64 with university or college degree—of whom 25% was mentally healthy, 51.3 vulnerable and 23.8% endangered—are to be handled as priority intervention target groups in a similarly difficult position. On organizational level, our survey involving the students of the University of Szeged, N=1565, provided data to prepare a strategy of mental health promotion for a university with a headcount exceeding 20,000. When developing an organizational strategy, it was important to gather information to estimate the proportions of target groups in which mental health promotion methods; for example, life management skills development, detection, psychological consultancy, psychotherapy, would be applied. Our scores show that 46.8% of the student participants were mentally healthy, 42.1% were vulnerable and 11.1% were endangered. These data convey relevant information as to the allocation of organizational resources within a university with a considerable headcount. In conclusion, The Mental State Questionnaire, as a valid smoothing method, is adequate to describe a community in a plain and informative way in the terms of mental health. The application of the method can promote the preparation, design and implementation of mental health promotion interventions.
Abstract: The purpose of this article is to find a method
of comparing designs for ordinal regression models using
quantile dispersion graphs in the presence of linear predictor
misspecification. The true relationship between response variable
and the corresponding control variables are usually unknown.
Experimenter assumes certain form of the linear predictor of the
ordinal regression models. The assumed form of the linear predictor
may not be correct always. Thus, the maximum likelihood estimates
(MLE) of the unknown parameters of the model may be biased due to
misspecification of the linear predictor. In this article, the uncertainty
in the linear predictor is represented by an unknown function. An
algorithm is provided to estimate the unknown function at the
design points where observations are available. The unknown function
is estimated at all points in the design region using multivariate
parametric kriging. The comparison of the designs are based on
a scalar valued function of the mean squared error of prediction
(MSEP) matrix, which incorporates both variance and bias of the
prediction caused by the misspecification in the linear predictor. The
designs are compared using quantile dispersion graphs approach.
The graphs also visually depict the robustness of the designs on the
changes in the parameter values. Numerical examples are presented
to illustrate the proposed methodology.
Abstract: Retinoblastoma is a rare type of childhood genetic cancer that affects children worldwide. The diagnosis is often missed due to lack of education and difficulty in presentation of the tumor. Frequently, the tumor on the retina is noticed by photography when the red-eye flash, commonly seen in normal eyes, is not produced. Instead, a yellow or white colored patch is seen or the child has a noticeable strabismus. Early detection can be life-saving though often results in removal of the affected eye. Remaining functioning in the healthy eye when the child is young has resulted in super-vision and high or above-average intelligence. Technological advancement of cameras has helped in early detection. Brain imaging has also made possible early detection of neurological diseases and, together with the monitoring of cortisol levels and yawning frequency, promises to be the next new early diagnostic tool for the detection of neurological diseases where cortisol insufficiency is particularly salient, such as multiple sclerosis and Cushing’s disease.
Abstract: A recently developed one-equation turbulence model
has been successfully applied to simulate turbulent flows with
various complexities. The model, which is based on the
transformation of the k-ε closure, is wall-distance free and equipped
with lagging destruction/dissipation terms. Test cases included shockboundary-
layer interaction flows over the NACA 0012 airfoil, an
axisymmetric bump, and the ONERA M6 wing. The capability of the
model to operate in a Scale Resolved Simulation (SRS) mode is
demonstrated through the simulation of a massive flow separation
over a circular cylinder at Re= 1.2 x106. An assessment of the results
against available experiments Menter (k-ε)1Eq and the Spalart-
Allmaras model that belongs to the single equation closure family is
made.
Abstract: Since Google launched Google Glass in 2012, numbers of commercial wearable devices were released, such as smart belt, smart band, smart shoes, smart clothes ... etc. However, most of these devices perform as sensors to show the readings of measurements and few of them provide the interactive feedback to the user. Furthermore, these devices are single task devices which are not able to communicate with each other. In this paper a new health promotion system, Ubiquitous Life People Informatics Engine (U-Life PIE), will be presented. This engine consists of People Informatics Engine (PIE) and the interactive user interface. PIE collects all the data from the compatible devices, analyzes this data comprehensively and communicates between devices via various application programming interfaces. All the data and informations are stored on the PIE unit, therefore, the user is able to view the instant and historical data on their mobile devices any time. It also provides the real-time hands-free feedback and instructions through the user interface visually, acoustically and tactilely. These feedback and instructions suggest the user to adjust their posture or habits in order to avoid the physical injuries and prevent illness.
Abstract: The performance of multiple tuned mass dampers to
mitigate the seismic vibration of structures considering real time
history data is investigated in this paper. Three different real
earthquake time history data like Kobe, Imperial Valley and
Mammoth Lake are taken in the present study. The multiple tuned
mass dampers (MTMD) are distributed at each storey. For
comparative study, single tuned mass damper (STMD) is installed at
top of the similar structure. This study is conducted for a fixed mass
ratio (5%) and fixed damping ratio (5%) of structures. Numerical
study is performed to evaluate the effectiveness of MTMDs and
overall system performance. The displacement, acceleration, base
shear and storey drift are obtained for both combined system
(structure with MTMD and structure with STMD) for all earthquakes.
The same responses are also obtained for structure without damper
system. From obtained results, it is investigated that the MTMD
configuration is more effective for controlling the seismic response of
the primary system with compare to STMD configuration.
Abstract: This study discusses a simple solution for the problem of shortage in learning resources for kindergarten teachers. Occasionally, kindergarten teachers cannot access proper resources by usual search methods as libraries or search engines. Furthermore, these methods require a long time and efforts for preparing. The study is expected to facilitate accessing learning resources. Moreover, it suggests a potential direction for using QR code inside the classroom. The present work proposes that QR code can be used for digitizing kindergarten curriculums and accessing various learning resources. It investigates using QR code for saving information related to the concepts which kindergarten teachers use in the current educational situation. The researchers have established a guide for kindergarten teachers based on the Egyptian official curriculum. The guide provides different learning resources for each scientific and mathematical concept in the curriculum, and each learning resource is represented as a QR code image that contains its URL. Therefore, kindergarten teachers can use smartphone applications for reading QR codes and displaying the related learning resources for students immediately. The guide has been provided to a group of 108 teachers for using inside their classrooms. The results showed that the teachers approved the guide, and gave a good response.
Abstract: A designing of a structure requires its realization on rough or sloping ground. Besides the problem of the stability of the landslide, the behavior of the foundations that are bearing the structure is influenced by the destabilizing effect of the ground’s slope. This article focuses on the analysis of the slope stability exposed to loading by introducing the different factors influencing the slope’s behavior on the one hand, and on the influence of this slope on the foundation’s behavior on the other hand. This study is about the elastoplastic modelization using FLAC 2D. This software is based on the finite difference method, which is one of the older methods of numeric resolution of differential equations system with initial and boundary conditions. It was developed for the geotechnical simulation calculation. The aim of this simulation is to demonstrate the notable effect of shear modulus « G », cohesion « C », inclination angle (edge) « β », and distance between the foundation and the head of the slope on the stability of the slope as well as the stability of the foundation. In our simulation, the slope is constituted by homogenous ground. The foundation is considered as rigid/hard; therefore, the loading is made by the application of the vertical strengths on the nodes which represent the contact between the foundation and the ground.
Abstract: One of the major developments in machine learning in the past decade is the ensemble method, which finds highly accurate classifier by combining many moderately accurate component classifiers. In this research work, new ensemble classification methods are proposed with homogeneous ensemble classifier using bagging and heterogeneous ensemble classifier using arcing and their performances are analyzed in terms of accuracy. A Classifier ensemble is designed using Radial Basis Function (RBF) and Support Vector Machine (SVM) as base classifiers. The feasibility and the benefits of the proposed approaches are demonstrated by the means of standard datasets of intrusion detection. The main originality of the proposed approach is based on three main parts: preprocessing phase, classification phase, and combining phase. A wide range of comparative experiments is conducted for standard datasets of intrusion detection. The performance of the proposed homogeneous and heterogeneous ensemble classifiers are compared to the performance of other standard homogeneous and heterogeneous ensemble methods. The standard homogeneous ensemble methods include Error correcting output codes, Dagging and heterogeneous ensemble methods include majority voting, stacking. The proposed ensemble methods provide significant improvement of accuracy compared to individual classifiers and the proposed bagged RBF and SVM performs significantly better than ECOC and Dagging and the proposed hybrid RBF-SVM performs significantly better than voting and stacking. Also heterogeneous models exhibit better results than homogeneous models for standard datasets of intrusion detection.
Abstract: Patient satisfaction represents a crucial aspect in the evaluation of health care services. Preoperative teaching provides the patient with pertinent information concerning the surgical process and the intended surgical procedure as well as anticipated patient behavior (anxiety, fear), expected sensation, and the probable outcomes. Although patient education is part of Accreditation protocols, it is not uniform at most places. The aim of this study was to try to assess the benefit of preoperative patient education on selected post-operative outcome parameters; mainly, post-operative pain scores, requirement of additional analgesia, return to activity of daily living and overall patient satisfaction, and try to standardize few education protocols. Dependent variables were measured before and after the treatment on a study population of 302 volunteers. Educational intervention was provided by the Investigator in the preoperative period to the study group through personal counseling. An information booklet contained detailed information was also provided. Statistical Analysis was done using Chi square test, Mann Whitney u test and Fischer Exact Test on a total of 302 subjects. P value
Abstract: This paper takes a philosophical view as axiom, and
reveals the relationship between information theory and Natural
Intelligence and Artificial Intelligence under real world conditions.
This paper also derives the relationship between natural intelligence
and nature. According to communication principle of information
theory, Natural Intelligence can be divided into real part and virtual
part. Based on information theory principle that Information does not
increase, the restriction mechanism of Natural Intelligence creativity is
conducted. The restriction mechanism of creativity reveals the limit of
natural intelligence and artificial intelligence. The paper provides a
new angle to observe natural intelligence and artificial intelligence.
Abstract: Today, insurers may use the yield curve as an indicator
evaluation of the profit or the performance of their portfolios;
therefore, they modeled it by one class of model that has the ability
to fit and forecast the future term structure of interest rates. This class
of model is the Nelson-Siegel-Svensson model. Unfortunately, many
authors have reported a lot of difficulties when they want to calibrate
the model because the optimization problem is not convex and has
multiple local optima. In this context, we implement a hybrid Particle
Swarm optimization and Nelder Mead algorithm in order to minimize
by least squares method, the difference between the zero-coupon
curve and the NSS curve.
Abstract: This paper presents the trajectory tracking control of a
spatial redundant hybrid manipulator. This manipulator consists of
two parallel manipulators which are a variable geometry truss (VGT)
module. In fact, each VGT module with 3-degress of freedom (DOF)
is a planar parallel manipulator and their operational planes of these
VGT modules are arranged to be orthogonal to each other. Also, the
manipulator contains a twist motion part attached to the top of the
second VGT module to supply the missing orientation of the endeffector.
These three modules constitute totally 7-DOF hybrid
(parallel-parallel) redundant spatial manipulator. The forward
kinematics equations of this manipulator are obtained, then,
according to these equations, the inverse kinematics is solved based
on an optimization with the joint limit avoidance. The dynamic
equations are formed by using virtual work method. In order to test
the performance of the redundant manipulator and the controllers
presented, two different desired trajectories are followed by using the
computed force control method and a switching control method. The
switching control method is combined with the computed force
control method and genetic algorithm. In the switching control
method, the genetic algorithm is only used for fine tuning in the
compensation of the trajectory tracking errors.
Abstract: In nearly all earthquakes of the past century that
resulted in moderate to significant damage, the occurrence of postearthquake
fire ignition (PEFI) has imposed a serious hazard and
caused severe damage, especially in urban areas. In order to reduce
the loss of life and property caused by post-earthquake fires, there is
a crucial need for predictive models to estimate the PEFI risk. The
parameters affecting PEFI risk can be categorized as: 1) factors
influencing fire ignition in normal (non-earthquake) condition,
including floor area, building category, ignitability, type of appliance,
and prevention devices, and 2) earthquake related factors contributing
to the PEFI risk, including building vulnerability and earthquake
characteristics such as intensity, peak ground acceleration, and peak
ground velocity. State-of-the-art statistical PEFI risk models are
solely based on limited available earthquake data, and therefore they
cannot predict the PEFI risk for areas with insufficient earthquake
records since such records are needed in estimating the PEFI model
parameters. In this paper, the correlation between normal condition
ignition risk, peak ground acceleration, and PEFI risk is examined in
an effort to offer a means for predicting post-earthquake ignition
events. An illustrative example is presented to demonstrate how such
correlation can be employed in a seismic area to predict PEFI hazard.
Abstract: In this study, natural bentonite was used as natural
clay material and samples were taken from the Kalecik district in
Ankara. In this research, bentonite is the subject of an analysis from
standpoint of assessing the basic properties of engineered barriers
with respect to the buffer material. Bentonite and sand mixtures were
prepared for tests. Some of clay minerals give relatively higher
hydraulic conductivity and lower swelling pressure. Generally,
hydraulic conductivity of these type clays is lower than
Abstract: During an earthquake, a bridge crane may be
subjected to multiple impacts between crane wheels and rail. In order
to model such phenomena, a time-history dynamic analysis with a
multi-scale approach is performed. The high frequency aspect of the
impacts between wheels and rails is taken into account by a Lagrange
explicit event-capturing algorithm based on a velocity-impulse
formulation to resolve contacts and impacts. An implicit temporal
scheme is used for the rest of the structure. The numerical coupling
between the implicit and the explicit schemes is achieved with a
heterogeneous asynchronous time-integrator.