Abstract: “Garbage enzyme", a fermentation product of kitchen waste, water and brown sugar, is claimed in the media as a multipurpose solution for household and agricultural uses. This study assesses the effects of dilutions (5% to 75%) of garbage enzyme in reducing pollutants in domestic wastewater. The pH of the garbage enzyme was found to be 3.5, BOD concentration about 150 mg/L. Test results showed that the garbage enzyme raised the wastewater-s BOD in proportion to its dilution due to its high organic content. For mixtures with more than 10% garbage enzyme, its pH remained acidic after the 5-day digestion period. However, it seems that ammonia nitrogen and phosphorus could be removed by the addition of the garbage enzyme. The most economic solution for removal of ammonia nitrogen and phosphorus was found to be 9%. Further tests are required to understand the removal mechanisms of the ammonia nitrogen and phosphorus.
Abstract: Vehicle suspension design must fulfill
some conflicting criteria. Among those is ride comfort
which is attained by minimizing the acceleration
transmitted to the sprung mass, via suspension spring
and damper. Also good handling of a vehicle is a
desirable property which requires stiff suspension and
therefore is in contrast with a vehicle with good ride.
Among the other desirable features of a suspension is
the minimization of the maximum travel of suspension.
This travel which is called suspension working space in
vehicle dynamics literature is also a design constraint
and it favors good ride. In this research a full car 8
degrees of freedom model has been developed and the
three above mentioned criteria, namely: ride, handling
and working space has been adopted as objective
functions. The Multi Objective Programming (MOP)
discipline has been used to find the Pareto Front and
some reasoning used to chose a design point between
these non dominated points of Pareto Front.
Abstract: In this paper, an estimation accuracy of multiple moving
talker tracking using a microphone array is improved. The tracking
can be achieved by the adaptive method in which two algorithms are integrated, namely, the PAST (Projection Approximation Subspace
Tracking) algorithm and the IPLS (Interior Point Least Square) algorithm. When either talker begins to speak again after a silent
period, an appropriate feasible region for an evaluation function of
the IPLS algorithm might not be set. Then, the tracking fails due to the incorrect updating. Therefore, if an increment of the number of
active talkers is detected, the feasible region must be reset. Then, a low cost realization is required for the high speed tracking and a high
accuracy realization is desired for the precise tracking. In this paper,
the directions roughly estimated using the delayed-sum-array method
are used for the resetting. Several results of experiments performed in
an actual room environment show the effectiveness of the proposed method.
Abstract: Existing literature ondesign reasoning seems to give
either one sided accounts on expert design behaviour based on
internal processing. In the same way ecological theoriesseem to
focus one sidedly on external elementsthat result in a lack of unifying
design cognition theory. Although current extended design cognition
studies acknowledge the intellectual interaction between internal and
external resources, there still seems to be insufficient understanding
of the complexities involved in such interactive processes. As
such,this paper proposes a novelmulti-directional model for design
researchers tomap the complex and dynamic conduct controlling
behaviour in which both the computational and ecological
perspectives are integrated in a vertical manner. A clear distinction
between identified intentional and emerging physical drivers, and
relationships between them during the early phases of experts- design
process, is demonstrated by presenting a case study in which the
model was employed.
Abstract: The major problem that wireless communication
systems undergo is multipath fading caused by scattering of the
transmitted signal. However, we can treat multipath propagation as
multiple channels between the transmitter and receiver to improve
the signal-to-scattering-noise ratio. While using Single Input
Multiple Output (SIMO) systems, the diversity receivers extract
multiple signal branches or copies of the same signal received from
different channels and apply gain combining schemes such as Root
Mean Square Gain Combining (RMSGC). RMSGC asymptotically
yields an identical performance to that of the theoretically optimal
Maximum Ratio Combining (MRC) for values of mean Signal-to-
Noise-Ratio (SNR) above a certain threshold value without the need
for SNR estimation. This paper introduces an improvement of
RMSGC using two different issues. We found that post-detection and
de-noising the received signals improve the performance of RMSGC
and lower the threshold SNR.
Abstract: Electrical Discharge Machine (EDM) is especially
used for the manufacturing of 3-D complex geometry and hard
material parts that are extremely difficult-to-machine by conventional
machining processes. In this paper authors review the research work
carried out in the development of die-sinking EDM within the past
decades for the improvement of machining characteristics such as
Material Removal Rate, Surface Roughness and Tool Wear Ratio. In
this review various techniques reported by EDM researchers for
improving the machining characteristics have been categorized as
process parameters optimization, multi spark technique, powder
mixed EDM, servo control system and pulse discriminating. At the
end, flexible machine controller is suggested for Die Sinking EDM to
enhance the machining characteristics and to achieve high-level
automation. Thus, die sinking EDM can be integrated with Computer
Integrated Manufacturing environment as a need of agile
manufacturing systems.
Abstract: Machining through turning was carried out in a lathe
to study the chip formation of Multiphase Ferrite
(F-B-M) microalloyed steel. Taguchi orthogonal array was employed
to perform the machining. Continuous and discontinuous chips were
formed for different cutting parameters like speed, feed and depth of
cut. Optical and scanning electron microscope was employed to
identify the chip morphology.
Abstract: Project managers are the ultimate responsible for the
overall characteristics of a project, i.e. they should deliver the project
on time with minimum cost and with maximum quality. It is vital for
any manager to decide a trade-off between these conflicting
objectives and they will be benefited of any scientific decision
support tool. Our work will try to determine optimal solutions (rather
than a single optimal solution) from which the project manager will
select his desirable choice to run the project. In this paper, the
problem in project scheduling notated as
(1,T|cpm,disc,mu|curve:quality,time,cost) will be studied. The
problem is multi-objective and the purpose is finding the Pareto
optimal front of time, cost and quality of a project
(curve:quality,time,cost), whose activities belong to a start to finish
activity relationship network (cpm) and they can be done in different
possible modes (mu) which are non-continuous or discrete (disc), and
each mode has a different cost, time and quality . The project is
constrained to a non-renewable resource i.e. money (1,T). Because
the problem is NP-Hard, to solve the problem, a meta-heuristic is
developed based on a version of genetic algorithm specially adapted
to solve multi-objective problems namely FastPGA. A sample project
with 30 activities is generated and then solved by the proposed
method.
Abstract: This paper aims to develop an algorithm of finite
capacity material requirement planning (FCMRP) system for a multistage
assembly flow shop. The developed FCMRP system has two
main stages. The first stage is to allocate operations to the first and
second priority work centers and also determine the sequence of the
operations on each work center. The second stage is to determine the
optimal start time of each operation by using a linear programming
model. Real data from a factory is used to analyze and evaluate the
effectiveness of the proposed FCMRP system and also to guarantee a
practical solution to the user. There are five performance measures,
namely, the total tardiness, the number of tardy orders, the total
earliness, the number of early orders, and the average flow-time. The
proposed FCMRP system offers an adjustable solution which is a
compromised solution among the conflicting performance measures.
The user can adjust the weight of each performance measure to
obtain the desired performance. The result shows that the combination
of FCMRP NP3 and EDD outperforms other combinations
in term of overall performance index. The calculation time for the
proposed FCMRP system is about 10 minutes which is practical for
the planners of the factory.
Abstract: In this paper, a novel multi join algorithm to join
multiple relations will be introduced. The novel algorithm is based
on a hashed-based join algorithm of two relations to produce a double index. This is done by scanning the two relations once. But
instead of moving the records into buckets, a double index will be built. This will eliminate the collision that can happen from a complete hash algorithm. The double index will be divided into join
buckets of similar categories from the two relations. The algorithm then joins buckets with similar keys to produce joined buckets. This
will lead at the end to a complete join index of the two relations. without actually joining the actual relations. The time complexity
required to build the join index of two categories is Om log m where m is the size of each category. Totaling time complexity to O n log m
for all buckets. The join index will be used to materialize the joined relation if required. Otherwise, it will be used along with other join
indices of other relations to build a lattice to be used in multi-join operations with minimal I/O requirements. The lattice of the join indices can be fitted into the main memory to reduce time complexity of the multi join algorithm.
Abstract: The malfunction of thermal protection system (TPS) caused by aerodynamic heating is a latent trouble to aircraft structure safety. Accurately predicting the structure temperature field is quite important for the TPS design of hypersonic vehicle. Since Thornton’s work in 1988, the coupled method of aerodynamic heating and heat transfer has developed rapidly. However, little attention has been paid to the influence of structural deformation on aerodynamic heating and structural temperature field. In the flight, especially the long-endurance flight, the structural deformation, caused by the aerodynamic heating and temperature rise, has a direct impact on the aerodynamic heating and structural temperature field. Thus, the coupled interaction cannot be neglected. In this paper, based on the method of static aero-thermo-elasticity, considering the influence of aero-thermo-elasticity deformation, the aerodynamic heating and heat transfer coupled results of hypersonic vehicle wing model were calculated. The results show that, for the low-curvature region, such as fuselage or center-section wing, structure deformation has little effect on temperature field. However, for the stagnation region with high curvature, the coupled effect is not negligible. Thus, it is quite important for the structure temperature prediction to take into account the effect of elastic deformation. This work has laid a solid foundation for improving the prediction accuracy of the temperature distribution of aircraft structures and the evaluation capacity of structural performance.
Abstract: This paper presents a new feature based dense stereo
matching algorithm to obtain the dense disparity map via dynamic
programming. After extraction of some proper features, we use some
matching constraints such as epipolar line, disparity limit, ordering
and limit of directional derivative of disparity as well. Also, a coarseto-
fine multiresolution strategy is used to decrease the search space
and therefore increase the accuracy and processing speed. The
proposed method links the detected feature points into the chains and
compares some of the feature points from different chains, to
increase the matching speed. We also employ color stereo matching
to increase the accuracy of the algorithm. Then after feature
matching, we use the dynamic programming to obtain the dense
disparity map. It differs from the classical DP methods in the stereo
vision, since it employs sparse disparity map obtained from the
feature based matching stage. The DP is also performed further on a
scan line, between any matched two feature points on that scan line.
Thus our algorithm is truly an optimization method. Our algorithm
offers a good trade off in terms of accuracy and computational
efficiency. Regarding the results of our experiments, the proposed
algorithm increases the accuracy from 20 to 70%, and reduces the
running time of the algorithm almost 70%.
Abstract: Y chromosome microdeletions are the most common
genetic cause of male infertility and screening for these
microdeletions in azoospermic or severely oligospermic men is now
standard practice. Analysis of the Y chromosome in men with
azoospermia or severe oligozoospermia has resulted in the
identification of three regions in the euchromatic part of the long arm
of the human Y chromosome (Yq11) that are frequently deleted in
men with otherwise unexplained spermatogenic failure. PCR analysis
of microdeletions in the AZFa, AZFb and AZFc regions of the
human Y chromosome is an important screening tool. The aim of this
study was to analyse the type of microdeletions in men with fertility
disorders in Slovakia. We evaluated 227 patients with azoospermia
and with normal karyotype. All patient samples were analyzed
cytogenetically. For PCR amplification of sequence-tagged sites
(STS) of the AZFa, AZFb and AZFc regions of the Y chromosome
was used Devyser AZF set. Fluorescently labeled primers for all
markers in one multiplex PCR reaction were used and for automated
visualization and identification of the STS markers we used genetic
analyzer ABi 3500xl (Life Technologies). We reported 13 cases of
deletions in the AZF region 5,73%. Particular types of deletions were
recorded in each region AZFa,b,c .The presence of microdeletions in
the AZFc region was the most frequent. The study confirmed that
percentage of microdeletions in the AZF region is low in Slovak
azoospermic patients, but important from a prognostic view.
Abstract: Groundlessness of application probability-statistic methods are especially shown at an early stage of the aviation GTE technical condition diagnosing, when the volume of the information has property of the fuzzy, limitations, uncertainty and efficiency of application of new technology Soft computing at these diagnosing stages by using the fuzzy logic and neural networks methods. It is made training with high accuracy of multiple linear and nonlinear models (the regression equations) received on the statistical fuzzy data basis. At the information sufficiency it is offered to use recurrent algorithm of aviation GTE technical condition identification on measurements of input and output parameters of the multiple linear and nonlinear generalized models at presence of noise measured (the new recursive least squares method (LSM)). As application of the given technique the estimation of the new operating aviation engine D30KU-154 technical condition at height H=10600 m was made.
Abstract: This study realizes an empirical investigation of main factors to develop an accounting career, stereotypes on accountants and accounting and perceptions on future career path for a sample of master students in accounting. The research provides some insight into what master students consider when choosing their future career paths. The most important two reasons chosen by students were “career opportunities" and “future earnings. They see accounting as structured, governed by conformity, requiring skills in working with numbers, monotonous, accurate, more efficient than effective but also absorbing, interesting and involving a certain degree of novelty. Although these students plan to start their careers in a multinational or accounting/audit firm, most of those plan to leave after five years. It resulted that women value more flexibility and time requiring special attention in retention policies practiced by firms.
Abstract: Memory Errors Detection and Correction aim to secure the transaction of data between the central processing unit of a satellite onboard computer and its local memory. In this paper, the application of a double-bit error detection and correction method is described and implemented in Field Programmable Gate Array (FPGA) technology. The performance of the proposed EDAC method is measured and compared with two different EDAC devices, using the same FPGA technology. Statistical analysis of single-event upset (SEU) and multiple-bit upset (MBU) activity in commercial memories onboard the first Algerian microsatellite Alsat-1 is given.
Abstract: Hopfield model of associative memory is studied in this work. In particular, two main problems that it possesses: the apparition of spurious patterns in the learning phase, implying the well-known effect of storing the opposite pattern, and the problem of its reduced capacity, meaning that it is not possible to store a great amount of patterns without increasing the error probability in the retrieving phase. In this paper, a method to avoid spurious patterns is presented and studied, and an explanation of the previously mentioned effect is given. Another technique to increase the capacity of a network is proposed here, based on the idea of using several reference points when storing patterns. It is studied in depth, and an explicit formula for the capacity of the network with this technique is provided.
Abstract: Skin color is an important visual cue for computer
vision systems involving human users. In this paper we combine skin
color and optical flow for detection and tracking of skin regions. We
apply these techniques to gesture recognition with encouraging
results. We propose a novel skin similarity measure. For grouping
detected skin regions we propose a novel skin region grouping
mechanism. The proposed techniques work with any number of skin
regions making them suitable for a multiuser scenario.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: Scheduling for the flexible job shop is very important
in both fields of production management and combinatorial
optimization. However, it quit difficult to achieve an optimal solution
to this problem with traditional optimization approaches owing to the
high computational complexity. The combining of several
optimization criteria induces additional complexity and new
problems. In this paper, a Pareto approach to solve the multi
objective flexible job shop scheduling problems is proposed. The
objectives considered are to minimize the overall completion time
(makespan) and total weighted tardiness (TWT). An effective
simulated annealing algorithm based on the proposed approach is
presented to solve multi objective flexible job shop scheduling
problem. An external memory of non-dominated solutions is
considered to save and update the non-dominated solutions during
the solution process. Numerical examples are used to evaluate and
study the performance of the proposed algorithm. The proposed
algorithm can be applied easily in real factory conditions and for
large size problems. It should thus be useful to both practitioners and
researchers.