Abstract: The designing of charge pump with high gain Op-
Amp is a challenging task for getting faithful response .Design of
high performance phase locked loop require ,a design of high
performance charge pump .We have designed a operational amplifier
for reducing the error caused by high speed glitch in a transistor and
mismatch currents . A separate Op-Amp has designed in 180 nm
CMOS technology by CADENCE VIRTUOSO tool. This paper
describes the design of high performance charge pump for GHz
CMOS PLL targeting orthogonal frequency division multiplexing
(OFDM) application. A high speed low power consumption Op-Amp
with more than 500 MHz bandwidth has designed for increasing the
speed of charge pump in Phase locked loop.
Abstract: Air bending is one of the important metal forming
processes, because of its simplicity and large field application.
Accuracy of analytical and empirical models reported for the analysis
of bending processes is governed by simplifying assumption and do
not consider the effect of dynamic parameters. Number of researches
is reported on the finite element analysis (FEA) of V-bending, Ubending,
and air V-bending processes. FEA of bending is found to be
very sensitive to many physical and numerical parameters. FE
models must be computationally efficient for practical use. Reported
work shows the 3D FEA of air bending process using Hyperform LSDYNA
and its comparison with, published 3D FEA results of air
bending in Ansys LS-DYNA and experimental results. Observing the
planer symmetry and based on the assumption of plane strain
condition, air bending problem was modeled in 2D with symmetric
boundary condition in width. Stress-strain results of 2D FEA were
compared with 3D FEA results and experiments. Simplification of
air bending problem from 3D to 2D resulted into tremendous
reduction in the solution time with only marginal effect on stressstrain
results. FE model simplification by studying the problem
symmetry is more efficient and practical approach for solution of
more complex large dimensions slow forming processes.
Abstract: Solar Cells are destined to supply electric energy beginning from primary resources. It can charge a battery up to 12V dc. For residential use an inverter for 12V dc to 220Vac conversion is desired. For this a static DC-AC converter is necessarily inserted between the solar cells and the distribution network. This paper describes a new P.W.M. strategy for a voltage source inverter. This modulation strategy reduces the energy losses and harmonics in the P.W.M. voltage source inverter. This technique allows the P.W.M. voltage source inverter to become a new feasible solution for solar home application.
Abstract: We have defined two suites of metrics, which cover
static and dynamic aspects of component assembly. The static
metrics measure complexity and criticality of component assembly,
wherein complexity is measured using Component Packing Density
and Component Interaction Density metrics. Further, four criticality
conditions namely, Link, Bridge, Inheritance and Size criticalities
have been identified and quantified. The complexity and criticality
metrics are combined to form a Triangular Metric, which can be used
to classify the type and nature of applications. Dynamic metrics are
collected during the runtime of a complete application. Dynamic
metrics are useful to identify super-component and to evaluate the
degree of utilisation of various components. In this paper both static
and dynamic metrics are evaluated using Weyuker-s set of properties.
The result shows that the metrics provide a valid means to measure
issues in component assembly. We relate our metrics suite with
McCall-s Quality Model and illustrate their impact on product
quality and to the management of component-based product
development.
Abstract: Imaging is defined as the process of obtaining
geometric images either two dimensional or three dimensional by scanning or digitizing the existing objects or products. In this research, it applied to retrieve 3D information of the human skin
surface in medical application. This research focuses on analyzing
and determining volume of leg ulcers using imaging devices. Volume
determination is one of the important criteria in clinical assessment of leg ulcer. The volume and size of the leg ulcer wound will give the
indication on responding to treatment whether healing or worsening.
Different imaging techniques are expected to give different result (and accuracies) in generating data and images. Midpoint projection
algorithm was used to reconstruct the cavity to solid model and compute the volume. Misinterpretation of the results can affect the
treatment efficacy. The objectives of this paper is to compare the
accuracy between two 3D data acquisition method, which is laser
triangulation and structured light methods, It was shown that using models with known volume, that structured-light-based 3D technique
produces better accuracy compared with laser triangulation data
acquisition method for leg ulcer volume determination.
Abstract: This paper deals with automatic sentence modality
recognition in French. In this work, only prosodic features are
considered. The sentences are recognized according to the three
following modalities: declarative, interrogative and exclamatory
sentences. This information will be used to animate a talking head for
deaf and hearing-impaired children. We first statistically study a real
radio corpus in order to assess the feasibility of the automatic
modeling of sentence types. Then, we test two sets of prosodic
features as well as two different classifiers and their combination. We
further focus our attention on questions recognition, as this modality
is certainly the most important one for the target application.
Abstract: Streaming Applications usually run in parallel or in
series that incrementally transform a stream of input data. It poses a
design challenge to break such an application into distinguishable
blocks and then to map them into independent hardware processing
elements. For this, there is required a generic controller that
automatically maps such a stream of data into independent processing
elements without any dependencies and manual considerations. In
this paper, Kahn Process Networks (KPN) for such streaming
applications is designed and developed that will be mapped on
MPSoC. This is designed in such a way that there is a generic Cbased
compiler that will take the mapping specifications as an input
from the user and then it will automate these design constraints and
automatically generate the synthesized RTL optimized code for
specified application.
Abstract: This paper presents the optimal design and development
of an axial flux motor for blood pump application. With the design
objective of maximizing the motor efficiency and torque, different
topologies of AFPM machine has been examined. Selection of
optimal magnet fraction, Halbach arrangement of rotor magnets and
the use of Soft Magnetic Composite (SMC) material for the stator
core results in a novel motor with improved efficiency and torque
profile. The results of the 3D Finite element analysis for the novel
motor have been shown.
Abstract: The fuzzy technique is an operator introduced in order
to simulate at a mathematical level the compensatory behavior in
process of decision making or subjective evaluation. The following
paper introduces such operators on hand of computer vision
application.
In this paper a novel method based on fuzzy logic reasoning
strategy is proposed for edge detection in digital images without
determining the threshold value. The proposed approach begins by
segmenting the images into regions using floating 3x3 binary matrix.
The edge pixels are mapped to a range of values distinct from each
other. The robustness of the proposed method results for different
captured images are compared to those obtained with the linear Sobel
operator. It is gave a permanent effect in the lines smoothness and
straightness for the straight lines and good roundness for the curved
lines. In the same time the corners get sharper and can be defined
easily.
Abstract: Video sensor networks operate on stringent requirements
of latency. Packets have a deadline within which they have
to be delivered. Violation of the deadline causes a packet to be
treated as lost and the loss of packets ultimately affects the quality
of the application. Network latency is typically a function of many
interacting components. In this paper, we propose ways of reducing
the forwarding latency of a packet at intermediate nodes. The
forwarding latency is caused by a combination of processing delay
and queueing delay. The former is incurred in order to determine the
next hop in dynamic routing. We show that unless link failures in a
very specific and unlikely pattern, a vast majority of these lookups
are redundant. To counter this we propose source routing as the
routing strategy. However, source routing suffers from issues related
to scalability and being impervious to network dynamics. We propose
solutions to counter these and show that source routing is definitely
a viable option in practical sized video networks. We also propose a
fast and fair packet scheduling algorithm that reduces queueing delay
at the nodes. We support our claims through extensive simulation on
realistic topologies with practical traffic loads and failure patterns.
Abstract: The essential oil of M. × piperita L. was formulated
into a topical gel. The prepared gel was characterized for its pH,
viscosity, spreadiblity, consistency and extrudiblity, while its stability
was evaluated under different temperature conditions. The prepared
M. × piperita oil gel was clear and transparent. The pH value of
developed gel was 6.6, while its viscosity was 1200 cP. Spreadability
and consistency of the M. × piperita oil gel was 10.7 g.cm/sec and 7
mm, respectively. The prepared gel showed good extrudiblity. During
the stability studies, no significant change in pH and viscosity as a
function of time for gel was observed, indicating stability of prepared
formulation. The gel developed in this study is expected to forward
the usage of M. × piperita essential towards commercial application.
Abstract: The high temperature degree and uniform
Temperature Distribution (TD) on surface of cookware which contact
with food are effective factors for improving cookware application.
Additionally, the ability of pan material in retaining the heat and nonreactivity
with foods are other significant properties. It is difficult for
single material to meet a wide variety of demands such as superior
thermal and chemical properties. Multi-Layer Plate (MLP) makes
more regular TD. In this study the main objectives are to find the best
structure (single or multi-layer) and materials to provide maximum
temperature degree and uniform TD up side surface of pan. And also
heat retaining of used metals with goal of improving the thermal
quality of pan to economize the energy. To achieve this aim were
employed Finite Element Method (FEM) for analyzing transient
thermal behavior of applied materials. The analysis has been
extended for different metals, we achieved the best temperature
profile and heat retaining in Copper/ Stainless Steel MLP.
Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: Circular tubes have been widely used as structural
members in engineering application. Therefore, its collapse behavior
has been studied for many decades, focusing on its energy absorption
characteristics. In order to predict the collapse behavior of members,
one could rely on the use of finite element codes or experiments.
These tools are helpful and high accuracy but costly and require
extensive running time. Therefore, an approximating model of tubes
collapse mechanism is an alternative for early step of design. This
paper is also aimed to develop a closed-form solution of thin-walled
circular tube subjected to bending. It has extended the Elchalakani et
al.-s model (Int. J. Mech. Sci.2002; 44:1117-1143) to include the
rate of energy dissipation of rolling hinge in the circumferential
direction. The 3-D geometrical collapse mechanism was analyzed by
adding the oblique hinge lines along the longitudinal tube within the
length of plastically deforming zone. The model was based on the
principal of energy rate conservation. Therefore, the rates of internal
energy dissipation were calculated for each hinge lines which are
defined in term of velocity field. Inextensional deformation and
perfect plastic material behavior was assumed in the derivation of
deformation energy rate. The analytical result was compared with
experimental result. The experiment was conducted with a number of
tubes having various D/t ratios. Good agreement between analytical
and experiment was achieved.
Abstract: In real-time networks a large number of application programs are relying on video data and heterogeneous data transmission techniques. The aim of this research is presenting a method for end-to-end vouch quality service in surface applicationlayer for sending video data in comparison form in wireless heterogeneous networks. This method tries to improve the video sending over the wireless heterogeneous networks with used techniques in surface layer, link and application. The offered method is showing a considerable improvement in quality observing by user. In addition to this, other specifications such as shortage of data load that had require to resending and limited the relation period length to require time for second data sending, help to be used the offered method in the wireless devices that have a limited energy. The presented method and the achieved improvement is simulated and presented in the NS-2 software.
Abstract: Tool Tracker is a client-server based application. It is essentially a catalogue of various network monitoring and management tools that are available online. There is a database maintained on the server side that contains the information about various tools. Several clients can access this information simultaneously and utilize this information. The various categories of tools considered are packet sniffers, port mappers, port scanners, encryption tools, and vulnerability scanners etc for the development of this application. This application provides a front end through which the user can invoke any tool from a central repository for the purpose of packet sniffing, port scanning, network analysis etc. Apart from the tool, its description and the help files associated with it would also be stored in the central repository. This facility will enable the user to view the documentation pertaining to the tool without having to download and install the tool. The application would update the central repository with the latest versions of the tools. The application would inform the user about the availability of a newer version of the tool currently being used and give the choice of installing the newer version to the user. Thus ToolTracker provides any network administrator that much needed abstraction and ease-ofuse with respect to the tools that he can use to efficiently monitor a network.
Abstract: In this paper, different approaches to solve the
forward kinematics of a three DOF actuator redundant hydraulic
parallel manipulator are presented. On the contrary to series
manipulators, the forward kinematic map of parallel manipulators
involves highly coupled nonlinear equations, which are almost
impossible to solve analytically. The proposed methods are using
neural networks identification with different structures to solve the
problem. The accuracy of the results of each method is analyzed in
detail and the advantages and the disadvantages of them in
computing the forward kinematic map of the given mechanism is
discussed in detail. It is concluded that ANFIS presents the best
performance compared to MLP, RBF and PNN networks in this
particular application.
Abstract: Results in one field necessarily give insight into the
others, and all have much potential for scientific and technological
application. The Hadamard-transform technique once been applied to
the spectrometry also has its use in the SNR Enhancement of OTDR.
In this report, a new set of code (Simplex-codes) is discussed and
where the addition gain of SNR come from is implied.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: Business process model describes process flow of a
business and can be seen as the requirement for developing a
software application. This paper discusses a BPM2CD guideline
which complements the Model Driven Architecture concept by
suggesting how to create a platform-independent software model in
the form of a UML class diagram from a business process model. An
important step is the identification of UML classes from the business
process model. A technique for object-oriented analysis called
domain analysis is borrowed and key concepts in the business
process model will be discovered and proposed as candidate classes
for the class diagram. The paper enhances this step by using ontology
search to help identify important classes for the business domain. As
ontology is a source of knowledge for a particular domain which
itself can link to ontologies of related domains, the search can give a
refined set of candidate classes for the resulting class diagram.