Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: In this paper, a new reverse converter for the moduli set {2n, 2n–1, 2n–1–1} is presented. We improved a previously introduced conversion algorithm for deriving an efficient hardware design for reverse converter. Hardware architecture of the proposed converter is based on carry-save adders and regular binary adders, without the requirement for modular adders. The presented design is faster than the latest introduced reverse converter for moduli set {2n, 2n–1, 2n–1–1}. Also, it has better performance than the reverse converters for the recently introduced moduli set {2n+1–1, 2n, 2n–1}
Abstract: Hepatocellular carcinoma, also called hepatoma, most
commonly appears in a patient with chronic viral hepatitis. In
patients with a higher suspicion of HCC, such as small or subtle
rising of serum enzymes levels, the best method of diagnosis
involves a CT scan of the abdomen, but only at high cost. The aim of
this study was to increase the ability of the physician to early detect
HCC, using a probabilistic neural network-based approach, in order
to save time and hospital resources.
Abstract: Web 2.0 (social networking, blogging and online
forums) can serve as a data source for social science research because
it contains vast amount of information from many different users.
The volume of that information has been growing at a very high rate
and becoming a network of heterogeneous data; this makes things
difficult to find and is therefore not almost useful. We have proposed
a novel theoretical model for gathering and processing data from
Web 2.0, which would reflect semantic content of web pages in
better way. This article deals with the analysis part of the model and
its usage for content analysis of blogs. The introductory part of the
article describes methodology for the gathering and processing data
from blogs. The next part of the article is focused on the evaluation
and content analysis of blogs, which write about specific trend.
Abstract: There are many researches to detect collision between real object and virtual object in 3D space. In general, these techniques are need to huge computing power. So, many research and study are constructed by using cloud computing, network computing, and distribute computing. As a reason of these, this paper proposed a novel fast 3D collision detection algorithm between real and virtual object using 2D intersection area. Proposed algorithm uses 4 multiple cameras and coarse-and-fine method to improve accuracy and speed performance of collision detection. In the coarse step, this system examines the intersection area between real and virtual object silhouettes from all camera views. The result of this step is the index of virtual sensors which has a possibility of collision in 3D space. To decide collision accurately, at the fine step, this system examines the collision detection in 3D space by using the visual hull algorithm. Performance of the algorithm is verified by comparing with existing algorithm. We believe proposed algorithm help many other research, study and application fields such as HCI, augmented reality, intelligent space, and so on.
Abstract: A thin coating of hexamethyldisiloxane and subsequent O2-plasma treatment was performed on mirror-polished titanium in order to regulate the wide range of wettability including 106 and almost 0 degrees of contact angles. The adsorption behavior of
fibronectin and albumin in both individual and competitive mode,
and initial attachment of fibroblasts and osteoblasts were investigated.
Individually, fibronectin adsorption showed a biphasic inclination, whereas albumin showed greater adsorption to hydrophobic surfaces.
In competitive mode, in solution containing both fibronectin and albumin, fibronectin showed greater adsorption on hydrophilic
surfaces, whereas Alb predominantly adsorbed on hydrophobic
surfaces. Initial attachment of both cells increased with increase in
surface wettability, in particular, on super-hydrophilic surface, which
correlated well with fibronectin adsorption in competitive mode.
These results suggest that a cold plasma-surface modification enabled
to regulate the surface wettability, and fibronectin adsorption may be
responsible for increasing cell adhesion on hydrophilic surfaces in a
body fluid
Abstract: Social bookmarking is an environment in which
the user gradually changes interests over time so that the tag
data associated with the current temporal period is usually more
important than tag data temporally far from the current period.
This implies that in the social tagging system, the newly tagged
items by the user are more relevant than older items. This study
proposes a novel recommender system that considers the users-
recent tag preferences. The proposed system includes the
following stages: grouping similar users into clusters using an
E-M clustering algorithm, finding similar resources based on
the user-s bookmarks, and recommending the top-N items to
the target user. The study examines the system-s information
retrieval performance using a dataset from del.icio.us, which is
a famous social bookmarking web site. Experimental results
show that the proposed system is better and more effective than
traditional approaches.
Abstract: The control of sprayer boom undesired vibrations pose a great challenge to investigators due to various disturbances and conditions. Sprayer boom movements lead to reduce of spread efficiency and crop yield. This paper describes the design of a novel control method for an active suspension system applying proportional-integral-derivative (PID) controller with an active force control (AFC) scheme integration of an iterative learning algorithm employed to a sprayer boom. The iterative learning as an intelligent method is principally used as a method to calculate the best value of the estimated inertia of the sprayer boom needed for the AFC loop. Results show that the proposed AFC-based scheme performs much better than the standard PID control technique. Also, this shows that the system is more robust and accurate.
Abstract: Non-Destructive evaluation of in-service power
transformer condition is necessary for avoiding catastrophic failures.
Dissolved Gas Analysis (DGA) is one of the important methods.
Traditional, statistical and intelligent DGA approaches have been
adopted for accurate classification of incipient fault sources.
Unfortunately, there are not often enough faulty patterns required for
sufficient training of intelligent systems. By bootstrapping the
shortcoming is expected to be alleviated and algorithms with better
classification success rates to be obtained. In this paper the
performance of an artificial neural network, K-Nearest Neighbour
and support vector machine methods using bootstrapped data are
detailed and shown that while the success rate of the ANN algorithms
improves remarkably, the outcome of the others do not benefit so
much from the provided enlarged data space. For assessment, two
databases are employed: IEC TC10 and a dataset collected from
reported data in papers. High average test success rate well exhibits
the remarkable outcome.
Abstract: Many measures have been proposed for machine
translation evaluation (MTE) while little research has been done on
the performance of MTE methods. This paper is an effort for MTE
performance analysis. A general frame is proposed for the description
of the MTE measure and the test suite, including whether the
automatic measure is consistent with human evaluation, whether
different results from various measures or test suites are consistent,
whether the content of the test suite is suitable for performance
evaluation, the degree of difficulty of the test suite and its influence
on the MTE, the relationship of MTE result significance and the size
of the test suite, etc. For a better clarification of the frame, several
experiment results are analyzed relating human evaluation, BLEU
evaluation, and typological MTE. A visualization method is
introduced for better presentation of the results. The study aims for
aid in construction of test suite and method selection in MTE
practice.
Abstract: As chip manufacturing technology is suddenly on the
threshold of major evaluation, which shrinks chip in size and
performance, LFSR (Linear Feedback Shift Register) is implemented
in layout level which develops the low power consumption chip,
using recent CMOS, sub-micrometer layout tools. Thus LFSR
counter can be a new trend setter in cryptography and is also
beneficial as compared to GRAY & BINARY counter and variety of
other applications.
This paper compares 3 architectures in terms of the hardware
implementation, CMOS layout and power consumption, using
Microwind CMOS layout tool. Thus it provides solution to a low
power architecture implementation of LFSR in CMOS VLSI.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: In this paper, we propose an improved 3D star skeleton
technique, which is a suitable skeletonization for human posture representation
and reflects the 3D information of human posture.
Moreover, the proposed technique is simple and then can be performed
in real-time. The existing skeleton construction techniques, such as
distance transformation, Voronoi diagram, and thinning, focus on the
precision of skeleton information. Therefore, those techniques are not
applicable to real-time posture recognition since they are computationally
expensive and highly susceptible to noise of boundary. Although
a 2D star skeleton was proposed to complement these problems,
it also has some limitations to describe the 3D information of the
posture. To represent human posture effectively, the constructed skeleton
should consider the 3D information of posture. The proposed 3D
star skeleton contains 3D data of human, and focuses on human action
and posture recognition. Our 3D star skeleton uses the 8 projection
maps which have 2D silhouette information and depth data of human
surface. And the extremal points can be extracted as the features of 3D
star skeleton, without searching whole boundary of object. Therefore,
on execution time, our 3D star skeleton is faster than the “greedy" 3D
star skeleton using the whole boundary points on the surface. Moreover,
our method can offer more accurate skeleton of posture than the
existing star skeleton since the 3D data for the object is concerned.
Additionally, we make a codebook, a collection of representative 3D
star skeletons about 7 postures, to recognize what posture of constructed
skeleton is.
Abstract: There are many studies in the literature on
institutional investors- efforts to improve corporate governance,
generally focused on the role of pension funds and private equity
firms. There are only a few studies that analyze the influence of
development banks in the governance of investee companies. The
objective of this research is to examine the role of the Brazilian
Development Bank (BNDES) in the governance of listed companies.
Our analysis provides evidence that companies in which BNDES is a
shareholder have better governance.
Abstract: Never has a revolution affected all aspects of
humanity as the communication revolution during the past two
decades. This revolution, with all its advances and utilities, swept the
world thus becoming an integral part of our lives, hence giving way
to emerging applications at the social, economic, political, and
educational levels. More specifically, such applications have changed
the delivery system through which learning is acquired by students.
Interaction with educators, accessibility to content, and creative
delivery options are but a few facets of the new learning experience
now being offered through the use of technology in the educational
field. With different success rates, third world countries have tried to
pace themselves with use of educational technology in advanced
parts of the world. One such country is the small rich-oil state of
Kuwait which has tried to adopt the e-educational model, however,
an evaluation of such trial is yet to be done. This study aimed to fill
the void of research conducted around that topic. The study explored
students' acceptance of incorporating communication technologies in
higher education in Kuwait. Students' responses to survey questions
presented an overview of the e-learning experience in this country,
and drew a framework through which implications and suggestions
for future research were discussed to better serve the advancement of
e-education in developing countries.
Abstract: The study examines the determinants of corporate cash holding of non-financial quoted firms in Nigeria using a sample of fifty four non-financial quoted firms listed on the Nigeria Stock Exchange for the period 1995-2009. Data were sourced from the Annual reports of the sampled firms and analyzed using Generalized Method of Moments(GMM). The study finds evidence supportive of a target adjustment model and that firms can not instantaneously adjust towards the target cash level owing to the fact that adjustment cost being costly,. Also, the result shows significant negative relationship between cash holdings and firm size, net working capital, return on asset and bank relationship and positive relationship with growth opportunities, leverage, inventories, account receivables and financial distress. Furthermore, there is no significant relationship between cash holdings and cash flow. In Nigerian setting, most of the variables that are relevant for explaining cash holdings in the Developed countries are found by this study to be relevant also in Nigeria.
Abstract: Vernacular building is considered as sustainable in
energy consumption and environment and its thermal performance is
more and more concerned by researchers. This paper investigates the
thermal property of the vernacular building in Lhasa by theoretical
analysis on the aspects of building form, envelope and materials etc.
The values of thermal resistance and thermal capacity of the envelope
are calculated and compared with the current China building code and
modern building case. And it is concluded that Lhasa vernacular
building meets the current China building code of thermal standards
and have better performance in some aspects, which is achieved by
various passive means with close response to local climate conditions.
Abstract: The present study is aim to prepare and evaluate the selfnanoemulsifying drug delivery (SNEDDS) system of a poorly water soluble drug valsartan in order to achieve a better dissolution rate which would further help in enhancing oral bioavailability. The present research work describes a SNEDDS of valsartan using labrafil M 1944 CS, Tween 80 and Transcutol HP. The pseudoternary phase diagrams with presence and absence of drug were plotted to check for the emulsification range and also to evaluate the effect of valsartan on the emulsification behavior of the phases. The mixtures consisting of oil (labrafil M 1944 CS) with surfactant (tween 80), co-surfactant (Transcutol HP) were found to be optimum formulations. Prepared formulations were evaluated for its particle size distribution, nanoemulsifying properties, robustness to dilution, self emulsication time, turbidity measurement, drug content and invitro dissolution. The optimized formulations are further evaluated for heating cooling cycle, centrifugation studies, freeze thaw cycling, particle size distribution and zeta potential were carried out to confirm the stability of the formed SNEDDS formulations. The prepared formulation revealed t a significant improvement in terms of the drug solubility as compared with marketed tablet and pure drug.
Abstract: Thermo-chemical treatment (TCT) such as pyrolysis
is getting recognized as a valid route for (i) materials and valuable
products and petrochemicals recovery; (ii) waste recycling; and (iii)
elemental characterization. Pyrolysis is also receiving renewed
attention for its operational, economical and environmental
advantages. In this study, samples of polyethylene terephthalate
(PET) and polystyrene (PS) were pyrolysed in a microthermobalance
reactor (using a thermogravimetric-TGA setup). Both
polymers were prepared and conditioned prior to experimentation.
The main objective was to determine the kinetic parameters of the
depolymerization reactions that occur within the thermal degradation
process. Overall kinetic rate constants (ko) and activation energies
(Eo) were determined using the general kinetics theory (GKT)
method previously used by a number of authors. Fitted correlations
were found and validated using the GKT, errors were within ± 5%.
This study represents a fundamental step to pave the way towards the
development of scaling relationship for the investigation of larger
scale reactors relevant to industry.