Abstract: The performance of high-resolution schemes is investigated for unsteady, inviscid and compressible multiphase flows. An Eulerian diffuse interface approach has been chosen for the simulation of multicomponent flow problems. The reduced fiveequation and seven equation models are used with HLL and HLLC approximation. The authors demonstrated the advantages and disadvantages of both seven equations and five equations models studying their performance with HLL and HLLC algorithms on simple test case. The seven equation model is based on two pressure, two velocity concept of Baer–Nunziato [10], while five equation model is based on the mixture velocity and pressure. The numerical evaluations of two variants of Riemann solvers have been conducted for the classical one-dimensional air-water shock tube and compared with analytical solution for error analysis.
Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: This work is a proposed model of CMOS for which
the algorithm has been created and then the performance evaluation
of this proposition has been done. In this context, another commonly
used model called ZSTT (Zero Switching Time Transient) model is
chosen to compare all the vital features and the results for the
Proposed Equivalent CMOS are promising. In the end, the excerpts
of the created algorithm are also included
Abstract: Pattern matching is one of the fundamental applications in molecular biology. Searching DNA related data is a common activity for molecular biologists. In this paper we explore the applicability of a new pattern matching technique called Index based Forward Backward Multiple Pattern Matching algorithm(IFBMPM), for DNA Sequences. Our approach avoids unnecessary comparisons in the DNA Sequence due to this; the number of comparisons of the proposed algorithm is very less compared to other existing popular methods. The number of comparisons rapidly decreases and execution time decreases accordingly and shows better performance.
Abstract: Bloom filter is a probabilistic and memory efficient
data structure designed to answer rapidly whether an element is
present in a set. It tells that the element is definitely not in the set but
its presence is with certain probability. The trade-off to use Bloom
filter is a certain configurable risk of false positives. The odds of a
false positive can be made very low if the number of hash function is
sufficiently large. For spam detection, weight is attached to each set
of elements. The spam weight for a word is a measure used to rate the
e-mail. Each word is assigned to a Bloom filter based on its weight.
The proposed work introduces an enhanced concept in Bloom filter
called Bin Bloom Filter (BBF). The performance of BBF over
conventional Bloom filter is evaluated under various optimization
techniques. Real time data set and synthetic data sets are used for
experimental analysis and the results are demonstrated for bin sizes 4,
5, 6 and 7. Finally analyzing the results, it is found that the BBF
which uses heuristic techniques performs better than the traditional
Bloom filter in spam detection.
Abstract: This study was initiated with a three prong objective.
One, to identify the relationship between Technological
Competencies factors (Technical Capability, Firm Innovativeness
and E-Business Practices and professional service firms- business
performance. To investigate the predictors of professional service
firms business performance and finally to evaluate the predictors of
business performance according to the type of professional service
firms, a survey questionnaire was deployed to collect empirical data.
The questionnaire was distributed to the owners of the professional
small medium size enterprises services in the Accounting, Legal,
Engineering and Architecture sectors. Analysis showed that all three
Technology Competency factors have moderate effect on business
performance. In addition, the regression models indicate that
technical capability is the most highly influential that could
determine business performance, followed by e-business practices
and firm innovativeness. Subsequently, the main predictor of
business performance for all types of firms is Technical capability.
Abstract: We present a BeeBot, Binus Multi-client Intelligent Telepresence Robot, a custom-build robot system specifically designed for teleconference with multiple person using omni directional actuator. The robot is controlled using a computer networks, so the manager/supervisor can direct the robot to the intended person to start a discussion/inspection. People tracking and autonomous navigation are intelligent features of this robot. We build a web application for controlling the multi-client telepresence robot and open-source teleconference system used. Experimental result presented and we evaluated its performance.
Abstract: It is well known that the channel capacity of Multiple-
Input-Multiple-Output (MIMO) system increases as the number of
antenna pairs between transmitter and receiver increases but it suffers
from multiple expensive RF chains. To reduce the cost of RF chains,
Antenna Selection (AS) method can offer a good tradeoff between
expense and performance. In a transmitting AS system, Channel
State Information (CSI) feedback is necessarily required to choose
the best subset of antennas in which the effects of delays and errors
occurred in feedback channels are the most dominant factors
degrading the performance of the AS method. This paper presents the
concept of AS method using CSI from channel reciprocity instead of
feedback method. Reciprocity technique can easily archive CSI by
utilizing a reverse channel where the forward and reverse channels
are symmetrically considered in time, frequency and location. In this
work, the capacity performance of MIMO system when using AS
method at transmitter with reciprocity channels is investigated by
own developing Testbed. The obtained results show that reciprocity
technique offers capacity close to a system with a perfect CSI and
gains a higher capacity than a system without AS method from 0.9 to
2.2 bps/Hz at SNR 10 dB.
Abstract: The “conveyor belt" as a product represents a
complex high performance component with a wide range of different
applications. Further development of these highly complex
components demands an integration of new technologies and new
enhanced materials. In this context nanostructured fillers appear to
have a more promising effect on the performance of the conveyor
belt composite than conventional micro-scaled fillers.
Within the project “DotTrans" nanostructured fillers, for example
silicon dioxide, are used to optimize performance parameters of
conveyor belt systems. The objective of the project includes
operating parameters like energy consumption or friction
characteristics as well as adaptive parameters like cut or wear
resistance.
Abstract: Ever increasing capacities of contemporary storage devices
inspire the vision to accumulate (personal) information without
the need of deleting old data over a long time-span. Hence the target
of SemanticLIFE project is to create a Personal Information Management
system for a human lifetime data. One of the most important
characteristics of the system is its dedication to retrieve information
in a very efficient way. By adopting user demands regarding the
reduction of ambiguities, our approach aims at a user-oriented and
yet powerful enough system with a satisfactory query performance.
We introduce the query system of SemanticLIFE, the Virtual Query
System, which uses emerging Semantic Web technologies to fulfill
users- requirements.
Abstract: In this paper, the effect of receive and/or transmit
antenna spacing on the performance (BER vs. SNR) of multipleantenna
systems is determined by using an RCS (Radar Cross
Section) channel model. In this physical model, the scatterers
existing in the propagation environment are modeled by their RCS so
that the correlation of the receive signal complex amplitudes, i.e.,
both magnitude and phase, can be estimated. The proposed RCS
channel model is then compared with classical models.
Abstract: In IETF RFC 2002, Mobile-IP was developed to
enable Laptobs to maintain Internet connectivity while moving
between subnets. However, the packet loss that comes from
switching subnets arises because network connectivity is lost while
the mobile host registers with the foreign agent and this encounters
large end-to-end packet delays. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated to describe the system in discrete events.
The heuristic of configuration file during practical Setup session for
registration parameters, on Cisco platform Router-1760 using IOS
12.3 (15)T and TFTP server S/W is created. Finally, stand-alone
performance simulations from Simulink Matlab, within each subnet
and also between subnets, are illustrated for reporting better end-toend
packet delays. Results verified the effectiveness of our Mathcad
analytical manipulation and experimental implementation. It showed
lower values of end-to-end packet delay for Mobile-IP using CIA
procedure-based early registration. Furthermore, it reported packets
flow between subnets to improve losses between subnets.
Abstract: Multi-Radio Multi-Channel Wireless Mesh Networks (MRMC-WMNs) operate at the backbone to access and route high volumes of traffic simultaneously. Such roles demand high network capacity, and long “online" time at the expense of accelerated transmission energy depletion and poor connectivity. This is the problem of transmission power control. Numerous power control methods for wireless networks are in literature. However, contributions towards MRMC configurations still face many challenges worth considering. In this paper, an energy-efficient power selection protocol called PMMUP is suggested at the Link-Layer. This protocol first divides the MRMC-WMN into a set of unified channel graphs (UCGs). A UCG consists of multiple radios interconnected to each other via a common wireless channel. In each UCG, a stochastic linear quadratic cost function is formulated. Each user minimizes this cost function consisting of trade-off between the size of unification states and the control action. Unification state variables come from independent UCGs and higher layers of the protocol stack. The PMMUP coordinates power optimizations at the network interface cards (NICs) of wireless mesh routers. The proposed PMMUP based algorithm converges fast analytically with a linear rate. Performance evaluations through simulations confirm the efficacy of the proposed dynamic power control.
Abstract: Careful design and selection of daylighting systems can greatly help in reducing not only artificial lighting use, but also decrease cooling energy consumption and, therefore, potential for downsizing air-conditioning systems. This paper aims to evaluate the energy performance of two types of top-light daylighting systems due to the integration of daylight together with artificial lighting in an existing examinaton hall in University Kebangsaan Malaysia, based on a hot and humid climate. Computer simulation models have been created for building case study (base case) and the two types of toplight daylighting designs for building energy performance evaluation using the VisualDOE 4.0 building energy simulation program. The finding revealed that daylighting through top-light systems is a very beneficial design strategy in reducing annual lighting energy consumption and the overall total annual energy consumption.
Abstract: This paper presents a new problem solving approach
that is able to generate optimal policy solution for finite-state
stochastic sequential decision-making problems with high data
efficiency. The proposed algorithm iteratively builds and improves
an approximate Markov Decision Process (MDP) model along with
cost-to-go value approximates by generating finite length trajectories
through the state-space. The approach creates a synergy between an
approximate evolving model and approximate cost-to-go values to
produce a sequence of improving policies finally converging to the
optimal policy through an intelligent and structured search of the
policy space. The approach modifies the policy update step of the
policy iteration so as to result in a speedy and stable convergence to
the optimal policy. We apply the algorithm to a non-holonomic
mobile robot control problem and compare its performance with
other Reinforcement Learning (RL) approaches, e.g., a) Q-learning,
b) Watkins Q(λ), c) SARSA(λ).
Abstract: IEEE 802.16 is a new wireless technology standard, it
has some advantages, including wider coverage, higher bandwidth,
and QoS support. As the new wireless technology for last mile
solution, there are designed two models in IEEE 802.16 standard. One
is PMP (point to multipoint) and the other is Mesh. In this paper we
only focus on IEEE 802.16 Mesh model. According to the IEEE
802.16 standard description, Mesh model has two scheduling modes,
centralized and distributed. Considering the pros and cons of the two
scheduling, we present the combined scheduling QoS framework that
the BS (Base Station) controls time frame scheduling and selects the
shortest path from source to destination directly. On the other hand, we
propose the Expedited Queue mechanism to cut down the transmission
time. The EQ mechanism can reduce a lot of end-to-end delay in our
QoS framework. Simulation study has shown that the average delay is
smaller than contrasts. Furthermore, our proposed scheme can also
achieve higher performance.
Abstract: In non destructive testing by radiography, a perfect
knowledge of the weld defect shape is an essential step to
appreciate the quality of the weld and make decision on its
acceptability or rejection. Because of the complex nature of the
considered images, and in order that the detected defect region
represents the most accurately possible the real defect, the choice
of thresholding methods must be done judiciously. In this paper,
performance criteria are used to conduct a comparative study of
four non parametric histogram thresholding methods for automatic
extraction of weld defect in radiographic images.
Abstract: In this paper, SFQ (Start Time Fair Queuing)
algorithm is analyzed when this is applied in computer networks to
know what kind of behavior the traffic in the net has when different
data sources are managed by the scheduler. Using the NS2 software
the computer networks were simulated to be able to get the graphs
showing the performance of the scheduler. Different traffic sources
were introduced in the scripts, trying to establish the real scenario.
Finally the results were that depending on the data source, the traffic
can be affected in different levels, when Constant Bite Rate is
applied, the scheduler ensures a constant level of data sent and
received, but the truth is that in the real life it is impossible to ensure
a level that resists the changes in work load.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any existing
network infrastructure or centralized administration. Because of the
limited transmission range of wireless network interfaces, multiple
"hops" may be needed to exchange data across the network. In order
to facilitate communication within the network, a routing protocol is
used to discover routes between nodes. The primary goal of such an
ad hoc network routing protocol is correct and efficient route
establishment between a pair of nodes so that messages may be
delivered in a timely manner. Route construction should be done
with a minimum of overhead and bandwidth consumption. This paper
examines two routing protocols for mobile ad hoc networks– the
Destination Sequenced Distance Vector (DSDV), the table- driven
protocol and the Ad hoc On- Demand Distance Vector routing
(AODV), an On –Demand protocol and evaluates both protocols
based on packet delivery fraction, normalized routing load, average
delay and throughput while varying number of nodes, speed and
pause time.
Abstract: This paper deals with the design of a periodic output
feedback controller for a flexible beam structure modeled with
Timoshenko beam theory, Finite Element Method, State space
methods and embedded piezoelectrics concept. The first 3 modes are
considered in modeling the beam. The main objective of this work is
to control the vibrations of the beam when subjected to an external
force. Shear piezoelectric sensors and actuators are embedded into
the top and bottom layers of a flexible aluminum beam structure, thus
making it intelligent and self-adaptive. The composite beam is
divided into 5 finite elements and the control actuator is placed at
finite element position 1, whereas the sensor is varied from position 2
to 5, i.e., from the nearby fixed end to the free end. 4 state space
SISO models are thus developed. Periodic Output Feedback (POF)
Controllers are designed for the 4 SISO models of the same plant to
control the flexural vibrations. The effect of placing the sensor at
different locations on the beam is observed and the performance of
the controller is evaluated for vibration control. Conclusions are
finally drawn.