Abstract: The abundance and availability of rice husk, an agricultural waste, make them as a good source for precursor of activated carbon. In this work, rice husk-based activated carbons were prepared via base treated chemical activation process prior the carbonization process. The effect of carbonization temperatures (400, 600 and 800oC) on their pore structure was evaluated through morphology analysis using scanning electron microscope (SEM). Sample carbonized at 800oC showed better evolution and development of pores as compared to those carbonized at 400 and 600oC. The potential of rice husk-based activated carbon as an alternative adsorbent was investigated for the removal of Ni(II), Zn(II) and Pb(II) from single metal aqueous solution. The adsorption studies using rice husk-based activated carbon as an adsorbent were carried out as a function of contact time at room temperature and the metal ions were analyzed using atomic absorption spectrophotometer (AAS). The ability to remove metal ion from single metal aqueous solution was found to be improved with the increasing of carbonization temperature. Among the three metal ions tested, Pb(II) ion gave the highest adsorption on rice husk-based activated carbon. The results obtained indicate the potential to utilize rice husk as a promising precursor for the preparation of activated carbon for removal of heavy metals.
Abstract: Feature selection is an important step in many pattern
classification problems. It is applied to select a subset of features,
from a much larger set, such that the selected subset is sufficient to
perform the classification task. Due to its importance, the problem of
feature selection has been investigated by many researchers. In this
paper, a novel feature subset search procedure that utilizes the Ant
Colony Optimization (ACO) is presented. The ACO is a
metaheuristic inspired by the behavior of real ants in their search for
the shortest paths to food sources. It looks for optimal solutions by
considering both local heuristics and previous knowledge. When
applied to two different classification problems, the proposed
algorithm achieved very promising results.
Abstract: In this paper, the use of beam search and look-ahead strategies for solving the strip packing problem (SPP) is investigated. Given a strip of fixed width W, unlimited length L, and a set of n circular pieces of known radii, the objective is to determine the minimum length of the initial strip that packs all the pieces. An augmented algorithm which combines beam search and a look-ahead strategies is proposed. The look-ahead is used in order to evaluate the nodes at each level of the tree search. The best nodes are then retained for branching. The computational investigation showed that the proposed augmented algorithm is able to improve the best known solutions of the literature on most instances used.
Abstract: In this paper, some common gearboxes vibration analysis methods and condition monitoring systems are explained. In addition, an experimental gearbox vibration analysis is discussed through a critical case history for a mixer gearbox related to Iran oil industry. The case history also consists of gear manufacturing (machining) recommendations, lubrication condition of gearbox and machinery maintenance activities that caused reduction in noise and vibration of the gearbox. Besides some of the recent patents and innovations in gearboxes, lubrication and vibration monitoring systems explained. Finally micro pitting and surface fatigue in pinion and bevel of mentioned horizontal to vertical gearbox discussed in details.
Abstract: The mobile users with Laptops need to have an
efficient access to i.e. their home personal data or to the Internet from
any place in the world, regardless of their location or point of
attachment, especially while roaming outside the home subnet. An
efficient interpretation of packet losses problem that is encountered
from this roaming is to the centric of all aspects in this work, to be
over-highlighted. The main previous works, such as BER-systems,
Amigos, and ns-2 implementation that are considered to be in
conjunction with that problem under study are reviewed and
discussed. Their drawbacks and limitations, of stopping only at
monitoring, and not to provide an actual solution for eliminating or
even restricting these losses, are mentioned. Besides that, the
framework around which we built a Triple-R sequence as a costeffective
solution to eliminate the packet losses and bridge the gap
between subnets, an area that until now has been largely neglected, is
presented. The results show that, in addition to the high bit error rate
of wireless mobile networks, mainly the low efficiency of mobile-IP
registration procedure is a direct cause of these packet losses.
Furthermore, the output of packet losses interpretation resulted an
illustrated triangle of the registration process. This triangle should be
further researched and analyzed in our future work.
Abstract: Tourism industries are rapidly increased for the last
few years especially in Malaysia. In order to attract more tourists,
Malaysian Governance encourages any effort to increase Malaysian
tourism industry. One of the efforts in attracting more tourists in
Malacca, Malaysia is a duck tour. Duck tour is an amphibious
sightseeing tour that works in two types of engines, hence, it required
a huge cost to operate and maintain the vehicle. To other country, it is
not so new but in Malaysia, it is just introduced, thus it does not have
any systematic routing yet. Therefore, this paper proposed an
optimization technique to formulate and schedule this tour to
minimize the operating costs by considering it into Travelling
Salesman Problem (TSP). The problem is then can be solved by one
of the optimization technique especially meta-heuristics approach
such as Tabu Search (TS) and Reactive Tabu Search (RTS).
Abstract: Benefits to the organisation are just as important as technical ability when it comes to software success. The challenge is to provide industry with professionals who understand this. In other words: How to teach computer engineering students to look beyond technology, and at the benefits of software to organizations? This paper reports on the conceptual design of a section of the computer networks module aimed to sensitize the students to the organisational context.
Checkland focuses on different worldviews represented by various role players in the organisation. He developed the Soft Systems Methodology that guides purposeful action in organisations, while incorporating different worldviews in the modeling process. If we can sensitize students to these methods, they are likely to appreciate the wider context of application of system software. This paper will provide literature on these concepts as well as detail on how the students will be guided to adopt these concepts.
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: Cantilever L-shaped walls are known to be relatively economical as retaining solution. The design starts by proportioning the wall dimensions for which the stability is checked for. A ratio between the lengths of the base and the stem, falling between 0.5 to 0.7 ensure in most case the stability requirements, however, the displacement pattern of the wall in terms of rotations and translations, and the lateral pressure profile, do not have the same figure for all wall’s proportioning, as it is usually assumed. In the present work the results of a numerical analysis are presented, different wall geometries were considered. The results show that the proportioning governs the equilibrium between the instantaneous rotation and the translation of the wall-toe, also, the lateral pressure estimation based on the average value between the at-rest and the active pressure, recommended by most design standards, is found to be not applicable for all walls.
Abstract: The study of non-equilibrium systems has attracted
increasing interest in recent years, mainly due to the lack of
theoretical frameworks, unlike their equilibrium counterparts.
Studying the steady state and/or simple systems is thus one of the
main interests. Hence in this work we have focused our attention on
the driven lattice gas model (DLG model) consisting of interacting
particles subject to an external field E. The dynamics of the system
are given by hopping of particles to nearby empty sites with rates
biased for jumps in the direction of E. Having used small two
dimensional systems of DLG model, the stochastic properties at nonequilibrium
steady state were analytically studied. To understand the
non-equilibrium phenomena, we have applied the analytic approach
via master equation to calculate probability function and analyze
violation of detailed balance in term of the fluctuation-dissipation
theorem. Monte Carlo simulations have been performed to validate
the analytic results.
Abstract: The electrokinetic flow resistance (electroviscous
effect) is predicted for steady state, pressure-driven liquid flow at
low Reynolds number in a microfluidic contraction of rectangular
cross-section. Calculations of the three dimensional flow are
performed in parallel using a finite volume numerical method. The
channel walls are assumed to carry a uniform charge density and the
liquid is taken to be a symmetric 1:1 electrolyte. Predictions are
presented for a single set of flow and electrokinetic parameters. It is
shown that the magnitude of the streaming potential gradient and the
charge density of counter-ions in the liquid is greater than that in
corresponding two-dimensional slit-like contraction geometry. The
apparent viscosity is found to be very close to the value for a
rectangular channel of uniform cross-section at the chosen Reynolds
number (Re = 0.1). It is speculated that the apparent viscosity for the
contraction geometry will increase as the Reynolds number is
reduced.
Abstract: The aim of this study was to evaluate the sensitivity
of a range of EEG indices to time-on-task effects and to a workload
manipulation (cueing), during performance of a resource-limited
vigilance task. Effects of task period and cueing on performance and
subjective state response were consistent with previous vigilance
studies and with resource theory. Two EEG indices – the Task Load
Index (TLI) and global lower frequency (LF) alpha power – showed
effects of task period and cueing similar to those seen with correct
detections. Across four successive task periods, the TLI declined and
LF alpha power increased. Cueing increased TLI and decreased LF
alpha. Other indices – the Engagement Index (EI), frontal theta and
upper frequency (UF) alpha failed to show these effects. However, EI
and frontal theta were sensitive to interactive effects of task period
and cueing, which may correspond to a stronger anxiety response to
the uncued task.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: Utilization of various sensors has made it possible to
extend capabilities of industrial robots. Among these are vision
sensors that are used for providing visual information to assist robot
controllers. This paper presents a method of integrating a vision
system and a simulation program with an industrial robot. The vision
system is employed to detect a target object and compute its location
in the robot environment. Then, the target object-s information is sent
to the robot controller via parallel communication port. The robot
controller uses the extracted object information and the simulation
program to control the robot arm for approaching, grasping and
relocating the object. This paper presents technical details of system
components and describes the methodology used for this integration.
It also provides a case study to prove the validity of the methodology
developed.
Abstract: This paper features the proposed modeling and design
of a Robust Decentralized Periodic Output Feedback (RDPOF)
control technique for the active vibration control of smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminum beam, thus giving rise to
a multimodel of the smart structure system. Using model order
reduction technique, the reduced order model of the higher order
system is obtained based on dominant eigen value retention and the
method of Davison. RDPOF controllers are designed for the above 5
multivariable-multimodel plant. The closed loop responses with the
RDPOF feedback gain and the magnitudes of the control input are
observed and the performance of the proposed multimodel smart
structure system with the controller is evaluated for vibration control.
Abstract: Case-Based Reasoning (CBR) is one of machine
learning algorithms for problem solving and learning that caught a lot
of attention over the last few years. In general, CBR is composed of
four main phases: retrieve the most similar case or cases, reuse the
case to solve the problem, revise or adapt the proposed solution, and
retain the learned cases before returning them to the case base for
learning purpose. Unfortunately, in many cases, this retain process
causes the uncontrolled case base growth. The problem affects
competence and performance of CBR systems. This paper proposes
competence-based maintenance method based on deletion policy
strategy for CBR. There are three main steps in this method. Step 1,
formulate problems. Step 2, determine coverage and reachability set
based on coverage value. Step 3, reduce case base size. The results
obtained show that this proposed method performs better than the
existing methods currently discussed in literature.
Abstract: The objective of this research was to study influence
parameters affecting to mechanical property of austenitic stainless
steel grade 304 (AISI 304) with Gas Metal Arc Welding (GMAW).
The research was applying factorial design experiment, which have
following interested parameters: welding current at 80, 90, and 100
Amps, welding speeds at 250, 300, and 350 mm/min, and shield gas
of 75% Ar + 25% CO2, 70% Ar + 25% CO2 + 5% O2 and 69.5% Ar +
25% CO2 + 5% O2 + 0.5% He gas. The study was done in following
aspects: ultimate tensile strength and elongation. A research study of
ultimate tensile strength found that main factor effect, which had the
highest strength to AISI 304 welding was shield gas of 70% Ar +
25% CO2 + 5% O2 at average of 954.81 N/mm2. Result of the highest
elongation was showed significantly different at interaction effect
between shield gas of 69.5%Ar+25%CO2+5%O2+.5%He and
welding speed at 250 mm/min at 47.94%.
Abstract: Due to some reasons, observed images are degraded which are mainly caused by noise. Recently image denoising using the wavelet transform has been attracting much attention. Waveletbased approach provides a particularly useful method for image denoising when the preservation of edges in the scene is of importance because the local adaptivity is based explicitly on the values of the wavelet detail coefficients. In this paper, we propose several methods of noise removal from degraded images with Gaussian noise by using adaptive wavelet threshold (Bayes Shrink, Modified Bayes Shrink and Normal Shrink). The proposed thresholds are simple and adaptive to each subband because the parameters required for estimating the threshold depend on subband data. Experimental results show that the proposed thresholds remove noise significantly and preserve the edges in the scene.
Abstract: Quantitative methods of economic decision-making as
the methodological base of the so called operational research
represent an important set of tools for managing complex economic
systems,both at the microeconomic level and on the macroeconomic
scale. Mathematical models of controlled and controlling processes
allow, by means of artificial experiments, obtaining information
foroptimalor optimum approaching managerial decision-making.The
quantitative methods of economic decision-making usually include a
methodology known as structural analysis -an analysisof
interdisciplinary production-consumption relations.
Abstract: Web services are pieces of software that can be invoked via a standardized protocol. They can be combined via formalized taskflow languages. The Open Knowledge system is a fully distributed system using P2P technology, that allows users to publish the setaskflows, and programmers to register their web services or publish implementations of them, for the roles described in these workflows.Besides this, the system offers the functionality to select a peer that could coordinate such an interaction model and inform web services when it is their 'turn'. In this paper we describe the architecture and implementation of the Open Knowledge Kernel which provides the core functionality of the Open Knowledge system.