Abstract: Plants are commonly known for its positive
correlation in reducing temperature. Since it can benefit buildings by
modifying the microclimate, it-s also believed capable of reducing
the internal temperature. Various experiments have been done in
Universiti Sains Malaysia, Penang to investigate the comparison in
thermal benefits between two rooms, one being a typical control
room (exposed wall) and the other a biofacade room (plant shaded
wall). The investigations were conducted during non-rainy season for
approximately a month. Climbing plant Psophocarpus
tetrogonobulus from legume species was selected as insulation for
the biofacade wall. Conclusions were made on whether the biofacade
can be used to tackle the energy efficiency, based on the parameters
taken into consideration.
Abstract: Nowadays the control of stator voltage at a constant frequency is one of the traditional and low expense methods in order to control the speed of induction motors near its nominal speed. The torque of induction motor is a nonlinear function of the firing angle, phase angle and speed. In this paper the speed control of induction motor regarding various load torque and under different conditions will be investigated based on a fuzzy controller with inverse training.
Abstract: The shortest path routing problem is a multiobjective
nonlinear optimization problem with constraints. This problem has
been addressed by considering Quality of service parameters, delay
and cost objectives separately or as a weighted sum of both
objectives. Multiobjective evolutionary algorithms can find multiple
pareto-optimal solutions in one single run and this ability makes them
attractive for solving problems with multiple and conflicting
objectives. This paper uses an elitist multiobjective evolutionary
algorithm based on the Non-dominated Sorting Genetic Algorithm
(NSGA), for solving the dynamic shortest path routing problem in
computer networks. A priority-based encoding scheme is proposed
for population initialization. Elitism ensures that the best solution
does not deteriorate in the next generations. Results for a sample test
network have been presented to demonstrate the capabilities of the
proposed approach to generate well-distributed pareto-optimal
solutions of dynamic routing problem in one single run. The results
obtained by NSGA are compared with single objective weighting
factor method for which Genetic Algorithm (GA) was applied.
Abstract: Rice seed expression (cDNA) library in the Lambda
Zap 11® phage constructed from the developing grain 10-20 days
after flowering was transformed into yeast for functional
complementation assays in three salt sensitive yeast mutants S.
cerevisiae strain CY162, G19 and Axt3K. Transformed cells of G19
and Axt3K with pYES vector with cDNA inserts showed enhance
tolerance than those with empty pYes vector. Sequencing of the
cDNA inserts revealed that they encode for the putative proteins with
the sequence homologous to rice putative protein PROLM24
(Os06g31070), a prolamin precursor. Expression of this cDNA did
not affect yeast growth in absence of salt. Axt3k and G19 strains
expressing the PROLM24 were able to grow upto 400 mM and 600
mM of NaCl respectively. Similarly, Axt3k mutant with PROLM24
expression showed comparatively higher growth rate in the medium
with excess LiCl (50 mM). The observation that expression of
PROLM24 rescued the salt sensitive phenotypes of G19 and Axt3k
indicates the existence of a regulatory system that ameliorates the
effect of salt stress in the transformed yeast mutants. However, the
exact function of the cDNA sequence, which shows partial sequence
homology to yeast UTR1 is not clear. Although UTR1 involved in
ferrous uptake and iron homeostasis in yeast cells, there is no
evidence to prove its role in Na+ homeostasis in yeast cells. Absence
of transmembrane regions in Os06g31070 protein indicates that salt
tolerance is achieved not through the direct functional
complementation of the mutant genes but through an alternative
mechanism.
Abstract: Most of the real queuing systems include special properties and constraints, which can not be analyzed directly by using the results of solved classical queuing models. Lack of Markov chains features, unexponential patterns and service constraints, are the mentioned conditions. This paper represents an applied general algorithm for analysis and optimizing the queuing systems. The algorithm stages are described through a real case study. It is consisted of an almost completed non-Markov system with limited number of customers and capacities as well as lots of common exception of real queuing networks. Simulation is used for optimizing this system. So introduced stages over the following article include primary modeling, determining queuing system kinds, index defining, statistical analysis and goodness of fit test, validation of model and optimizing methods of system with simulation.
Abstract: Increase in globalization of capital markets brings the
higher requirements on financial information provided for investors
who look for a highly comparable information. Paper deals with the
advantages and limitations of applying International Financial
Reporting Standards (IFRS) in the Czech Republic and Ukraine. As a
greatest limit for full adoption of IFRS shall be acknowledged the
strong connection of continental accounting to tax system and
enormous high administrative burden for IFRS appliers.
Abstract: Cosmic showers, during the transit through space, produce
sub - products as a result of interactions with the intergalactic
or interstellar medium which after entering earth generate secondary
particles called Extensive Air Shower (EAS). Detection and analysis
of High Energy Particle Showers involve a plethora of theoretical and
experimental works with a host of constraints resulting in inaccuracies
in measurements. Therefore, there exist a necessity to develop a
readily available system based on soft-computational approaches
which can be used for EAS analysis. This is due to the fact that soft
computational tools such as Artificial Neural Network (ANN)s can be
trained as classifiers to adapt and learn the surrounding variations. But
single classifiers fail to reach optimality of decision making in many
situations for which Multiple Classifier System (MCS) are preferred
to enhance the ability of the system to make decisions adjusting
to finer variations. This work describes the formation of an MCS
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN) with data inputs
from correlation mapping Self Organizing Map (SOM) blocks and
the output optimized by another SOM. The results show that the setup
can be adopted for real time practical applications for prediction
of primary energy and location of EAS from density values captured
using detectors in a circular grid.
Abstract: The design of a pattern classifier includes an attempt
to select, among a set of possible features, a minimum subset of
weakly correlated features that better discriminate the pattern classes.
This is usually a difficult task in practice, normally requiring the
application of heuristic knowledge about the specific problem
domain. The selection and quality of the features representing each
pattern have a considerable bearing on the success of subsequent
pattern classification. Feature extraction is the process of deriving
new features from the original features in order to reduce the cost of
feature measurement, increase classifier efficiency, and allow higher
classification accuracy. Many current feature extraction techniques
involve linear transformations of the original pattern vectors to new
vectors of lower dimensionality. While this is useful for data
visualization and increasing classification efficiency, it does not
necessarily reduce the number of features that must be measured
since each new feature may be a linear combination of all of the
features in the original pattern vector. In this paper a new approach is
presented to feature extraction in which feature selection, feature
extraction, and classifier training are performed simultaneously using
a genetic algorithm. In this approach each feature value is first
normalized by a linear equation, then scaled by the associated weight
prior to training, testing, and classification. A knn classifier is used to
evaluate each set of feature weights. The genetic algorithm optimizes
a vector of feature weights, which are used to scale the individual
features in the original pattern vectors in either a linear or a nonlinear
fashion. By this approach, the number of features used in classifying
can be finely reduced.
Abstract: This work aims to investigate a potential of
microalgae for utilizing industrial wastewater as a cheap nutrient for
their growth and oil accumulation. Wastewater was collected from
the effluent ponds of agro-industrial factories (cassava and ethanol
production plants). Only 2 microalgal strains were isolated and
identified as Scenedesmus quadricauda and Chlorella sp.. However,
only S. quadricauda was selected to cultivate in various wastewater
concentrations (10%, 20%, 40%, 60%, 80% and 100%). The highest
biomass obtained at 6.6×106 and 6.27×106 cells/ml when 60%
wastewater was used in flask and photo-bioreactor. The cultures gave
the highest lipid content at 18.58 % and 42.86% in cases of S.
quadricauda and S. obliquus. In addition, under salt stress (1.0 M
NaCl), S. obliquus demonstrated the highest lipid content at 50%
which was much more than the case of no NaCl adding. However, the
concentration of NaCl does not affect on lipid accumulation in case
of S. quadricauda.
Abstract: A new approach based on the consideration that electroencephalogram (EEG) signals are chaotic signals was presented for automated diagnosis of electroencephalographic changes. This consideration was tested successfully using the nonlinear dynamics tools, like the computation of Lyapunov exponents. This paper presented the usage of statistics over the set of the Lyapunov exponents in order to reduce the dimensionality of the extracted feature vectors. Since classification is more accurate when the pattern is simplified through representation by important features, feature extraction and selection play an important role in classifying systems such as neural networks. Multilayer perceptron neural network (MLPNN) architectures were formulated and used as basis for detection of electroencephalographic changes. Three types of EEG signals (EEG signals recorded from healthy volunteers with eyes open, epilepsy patients in the epileptogenic zone during a seizure-free interval, and epilepsy patients during epileptic seizures) were classified. The selected Lyapunov exponents of the EEG signals were used as inputs of the MLPNN trained with Levenberg- Marquardt algorithm. The classification results confirmed that the proposed MLPNN has potential in detecting the electroencephalographic changes.
Abstract: In this study, a nickel film with nano-crystalline grains,
high hardness and smooth surface was electrodeposited using a post
supercritical carbon dioxide (CO2) mixed Watts electrolyte. Although
the hardness was not as high as its Sc-CO2 counterpart, the thin coating
contained significantly less number of nano-sized pinholes. By
measuring the escape concentration of the dissolved CO2 in post
Sc-CO2 mixed electrolyte with the elapsed time, it was believed that
the residue of dissolved CO2 bubbles should closely relate to the
improvement in hardness and surface roughness over its conventional
plating counterpart. Therefore, shortening the duration of
electroplating with the raise of current density up to 0.5 A/cm2 could
effectively retain more post Sc-CO2 mixing effect. This study not only
confirms the roles of dissolved CO2 bubbles in electrolyte but also
provides a potential process to overcome most issues associated with
the cost in building high-pressure chamber for large size products and
continuous plating using supercritical method.
Abstract: The demand for higher performance graphics
continues to grow because of the incessant desire towards realism.
And, rapid advances in fabrication technology have enabled us to
build several processor cores on a single die. Hence, it is important to
develop single chip parallel architectures for such data-intensive
applications. In this paper, we propose an efficient PIM architectures
tailored for computer graphics which requires a large number of
memory accesses. We then address the two important tasks necessary
for maximally exploiting the parallelism provided by the architecture,
namely, partitioning and placement of graphic data, which affect
respectively load balances and communication costs. Under the
constraints of uniform partitioning, we develop approaches for optimal
partitioning and placement, which significantly reduce search space.
We also present heuristics for identifying near-optimal placement,
since the search space for placement is impractically large despite our
optimization. We then demonstrate the effectiveness of our partitioning
and placement approaches via analysis of example scenes; simulation
results show considerable search space reductions, and our heuristics
for placement performs close to optimal – the average ratio of
communication overheads between our heuristics and the optimal was
1.05. Our uniform partitioning showed average load-balance ratio of
1.47 for geometry processing and 1.44 for rasterization, which is
reasonable.
Abstract: The intention of this paper is, to help the user of evolutionary algorithms to adapt them easier to their problem at hand. For a lot of problems in the technical field it is not necessary to reach an optimum solution, but to reach a good solution in time. In many cases the solution is undetermined or there doesn-t exist a method to determine the solution. For these cases an evolutionary algorithm can be useful. This paper intents to give the user rules of thumb with which it is easier to decide if the problem is suitable for an evolutionary algorithm and how to design them.
Abstract: Programmable logic controllers are the main controllers in the today's industries; they are used for several applications in industrial control systems and there are lots of examples exist from the PLC applications in industries especially in big companies and plants such as refineries, power plants, petrochemical companies, steel companies, and food and production companies. In the PLCs there are some functions in the function library in software that can be used in PLC programs as basic program elements. The aim of this project are introducing and implementing a new function block of a neural network to the function library of PLC. This block can be applied for some control applications or nonlinear functions calculations after it has been trained for these applications. The implemented neural network is a Perceptron neural network with three layers, three input nodes and one output node. The block can be used in manual or automatic mode. In this paper the structure of the implemented function block, the parameters and the training method of the network are presented by considering the especial method of PLC programming and its complexities. Finally the application of the new block is compared with a classic simulated block and the results are presented.
Abstract: A road pricing game is a game where various stakeholders and/or regions with different (and usually conflicting) objectives compete for toll setting in a given transportation network to satisfy their individual objectives. We investigate some classical game theoretical solution concepts for the road pricing game. We establish results for the road pricing game so that stakeholders and/or regions playing such a game will beforehand know what is obtainable. This will save time and argument, and above all, get rid of the feelings of unfairness among the competing actors and road users. Among the classical solution concepts we investigate is Nash equilibrium. In particular, we show that no pure Nash equilibrium exists among the actors, and further illustrate that even “mixed Nash equilibrium" may not be achievable in the road pricing game. The paper also demonstrates the type of coalitions that are not only reachable, but also stable and profitable for the actors involved.
Abstract: The recovery of metal values and safe disposal of
spent catalyst is gaining interest due to both its hazardous nature and
increased regulation associated with disposal methods. Prior to the
recovery of the valuable metals, removal of entrained deposits limit
the diffusion of lixiviate resulting in low recovery of metals must be
taken into consideration. Therefore, petroleum refinery spent catalyst
was subjected to acetone washing and roasting at 500oC. The treated
samples were investigated for metals bioleaching using
Acidithiobacillus ferrooxidans in batch reactors and the leaching
efficiencies were compared. It was found out that acetone washed
spent catalysts results in better metal recovery compare to roasted
spent. About 83% Ni, 20% Al, 50% Mo and 73% V were leached
using the acetone washed spent catalyst. In both the cases, Ni, V and
Mo was high compared to Al.
Abstract: Protective clothing limits heat transfer and hampers
task performance due to the increased weight. Militarism protective
clothing enables humans to operate in adverse environments. In the
selection and evaluation of militarism protective clothing attention
should be given to heat strain, ergonomic and fit issues next to the
actual protection it offers.
Fifty Male healthy subjects participated in the study. The subjects
were dressed in shorts, T-shirts, socks, sneakers and four deferent
kinds of militarism protective clothing such as CS, CSB, CS with
NBC protection and CS with NBC- protection added.
Ergonomically and psychological strains of every four cloths were
investigated on subjects by walking on a treadmill (7km/hour) with a
19.7 kg backpack. As a result of these tests were showed that, the
highest heart rate was found wearing the NBC-protection added
outfit, the highest temperatures were observed wearing NBCprotection
added, followed by respectively CS with NBC protection,
CSB and CS and the highest value for thermal comfort (implying
worst thermal comfort) was observed wearing NBC-protection
added.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: Bone marrow-derived stem cells have been widely
studied as an alternative source of stem cells. Mesenchymal stem
cells (MSCs) were mostly investigated and studies showed MSCs can
promote neurogenesis. Little is known about the non-mesenchymal
mononuclear cell fraction, which contains both hematopoietic and
nonhematopoietic cells, including monocytes and endothelial
progenitor cells. This study focused on unfractionated bone marrow
mononuclear cells (BMMCs), which remained 72 h after MSCs were
adhered to the culture plates. We showed that BMMC-conditioned
medium promoted morphological changes of human SH-SY5Y
neuroblastoma cells from an epithelial-like phenotype towards a
neuron-like phenotype as indicated by an increase in neurite
outgrowth, like those observed in retinoic acid (RA)-treated cells.
The result could be explained by the effects of trophic factors
released from BMMCs, as shown in the RT-PCR results that
BMMCs expressed nerve growth factor (NGF), brain-derived
neurotrophic factor (BDNF), and ciliary neurotrophic factor (CNTF).
Similar results on the cell proliferation rate were also observed
between RA-treated cells and cells cultured in BMMC-conditioned
medium, suggesting that cells creased proliferating and differentiated
into a neuronal phenotype. Using real-time RT-PCR, a significantly
increased expression of tyrosine hydroxylase (TH) mRNA in SHSY5Y
cells indicated that BMMC-conditioned medium induced
catecholaminergic identities in differentiated SH-SY5Y cells.
Abstract: The Norwegian Military Academy (Army) has
initiated a project with the main ambition to explore possible avenues
to enhancing operational effectiveness through an increased use of
simulation-based training and exercises. Within a cost/benefit
framework, we discuss opportunities and limitations of vertical and
horizontal integration of the existing tactical training system. Vertical
integration implies expanding the existing training system to span the
full range of training from tactical level (platoon, company) to
command and staff level (battalion, brigade). Horizontal integration
means including other domains than army tactics and staff
procedures in the training, such as military ethics, foreign languages,
leadership and decision making. We discuss each of the integration
options with respect to purpose and content of training, "best
practice" for organising and conducting simulation-based training,
and suggest how to evaluate training procedures and measure
learning outcomes. We conclude by giving guidelines towards further
explorative work and possible implementation.