Abstract: In the present work, the effect of load and sliding
distance on the performance tribology of commercially used
aluminium-silicon engine block and piston was evaluated at ambient
conditions with humidity of 80% under dry sliding conditions using a
pin-on-disc with two different loads of 5N and 20N yielding applied
pressure of 0.30MPa and 1.4MPa, respectively, at sliding velocity of
0.29ms-1 and with varying sliding distance ranging from 260m-
4200m. Factors and conditions that had significant effect were
identified. The results showed that the load and the sliding distance
affect the wear rate of the alloys and the wear rate increased with
increasing load for both the alloys. Wear rate also increases almost
linearly at low loads and increase to a maximum then attain a plateau
with increasing sliding distance. For both applied loads the piston
alloy showed the better performance due to higher Ni and Mg
content. The worn surface and wear debris was characterized by
optical microscope, SEM and EDX analyzer. The worn surface was
characterized by surface with shallow grooves at loads while the
groove width and depth increased as the loads increases. Oxidative
wear was found to be the predominant mechanisms in the dry sliding
of Al-Si alloys at low loads.
Abstract: In order to investigate the effect of Plant Growth
Promoting Rhizobacteria (PGPR) and rhizobium bacteria on grain
yield and some agronomic traits of mungbean (Vigna radiate L.), an
experiment was carried out based on randomized complete block
design with three replications in Malekshahi, Ilam province, Iran
during 2012-2013 cropping season. Experimental treatments
consisted of control treatment, inoculation with rhizobium bacteria,
rhizobium bacteria and Azotobacter, rhizobium bacteria and
Azospirillum, rhizobium bacteria and Pseudomonas, rhizobium
bacteria, Azotobacter and Azospirillum, rhizobium bacteria,
Azotobacter and Pseudomonas, rhizobium bacteria, Azospirillum and
Pseudomonas and rhizobium bacteria, Azotobacter, Azospirillum and
Pseudomonas. The results showed that the effect of PGPR and
rhizobium bacteria were significant affect on grain and its
components in mungbean plant. Grain yield significantly increased
by PGPR and rhizobium bacteria, so that the maximum grain yield
was obtained from rhizobium bacteria + Azospirillum +
Pseudomonas with the amount of 2287 kg.ha-1 as compared to
control treatment. Excessive application of chemical fertilizers causes
environmental and economic problems. That is, the overfertilization
of P and N leads to pollution due to soil erosion and runoff water, so
the use of PGPR and rhizobium bacteria can be justified due to
reduce input costs, increase in grain yield and environmental friendly.
Abstract: In this paper, we have proposed a numerical method
for solving fuzzy Fredholm integral equation of the second kind. In
this method a combination of orthonormal Bernstein and Block-Pulse
functions are used. In most cases, the proposed method leads to
the exact solution. The advantages of this method are shown by an
example and calculate the error analysis.
Abstract: The system is designed to show images which are
related to the query image. Extracting color, texture, and shape
features from an image plays a vital role in content-based image
retrieval (CBIR). Initially RGB image is converted into HSV color
space due to its perceptual uniformity. From the HSV image, Color
features are extracted using block color histogram, texture features
using Haar transform and shape feature using Fuzzy C-means
Algorithm. Then, the characteristics of the global and local color
histogram, texture features through co-occurrence matrix and Haar
wavelet transform and shape are compared and analyzed for CBIR.
Finally, the best method of each feature is fused during similarity
measure to improve image retrieval effectiveness and accuracy.
Abstract: Color Histogram is considered as the oldest method
used by CBIR systems for indexing images. In turn, the global
histograms do not include the spatial information; this is why the
other techniques coming later have attempted to encounter this
limitation by involving the segmentation task as a preprocessing step.
The weak segmentation is employed by the local histograms while
other methods as CCV (Color Coherent Vector) are based on strong
segmentation. The indexation based on local histograms consists of
splitting the image into N overlapping blocks or sub-regions, and
then the histogram of each block is computed. The dissimilarity
between two images is reduced, as consequence, to compute the
distance between the N local histograms of the both images resulting
then in N*N values; generally, the lowest value is taken into account
to rank images, that means that the lowest value is that which helps to
designate which sub-region utilized to index images of the collection
being asked. In this paper, we make under light the local histogram
indexation method in the hope to compare the results obtained against
those given by the global histogram. We address also another
noteworthy issue when Relying on local histograms namely which
value, among N*N values, to trust on when comparing images, in
other words, which sub-region among the N*N sub-regions on which
we base to index images. Based on the results achieved here, it seems
that relying on the local histograms, which needs to pose an extra
overhead on the system by involving another preprocessing step
naming segmentation, does not necessary mean that it produces better
results. In addition to that, we have proposed here some ideas to
select the local histogram on which we rely on to encode the image
rather than relying on the local histogram having lowest distance with
the query histograms.
Abstract: The relationship between eigenstructure (eigenvalues
and eigenvectors) and latent structure (latent roots and latent vectors)
is established. In control theory eigenstructure is associated with
the state space description of a dynamic multi-variable system and
a latent structure is associated with its matrix fraction description.
Beginning with block controller and block observer state space forms
and moving on to any general state space form, we develop the
identities that relate eigenvectors and latent vectors in either direction.
Numerical examples illustrate this result. A brief discussion of the
potential of these identities in linear control system design follows.
Additionally, we present a consequent result: a quick and easy
method to solve the polynomial eigenvalue problem for regular matrix
polynomials.
Abstract: The high Peak to Average Power Ratio (PAR) in Filter
Bank Multicarrier with Offset Quadrature Amplitude Modulation
(FBMC-OQAM) can significantly reduce power efficiency and
performance. In this paper, we address the problem of PAPR
reduction for FBMC-OQAM systems using Tone Reservation (TR)
technique. Due to the overlapping structure of FBMCOQAM signals,
directly applying TR schemes of OFDM systems to FBMC-OQAM
systems is not effective. We improve the tone reservation (TR)
technique by employing sliding window with Active Constellation
Extension for the PAPR reduction of FBMC-OQAM signals, called
sliding window tone reservation Active Constellation Extension
(SW-TRACE) technique. The proposed SW-TRACE technique uses
the peak reduction tones (PRTs) of several consecutive data
blocks to cancel the peaks of the FBMC-OQAM signal inside a
window, with dynamically extending outer constellation points in
active(data-carrying) channels, within margin-preserving constraints,
in order to minimize the peak magnitude. Analysis and simulation
results compared to the existing Tone Reservation (TR) technique for
FBMC/OQAM system. The proposed method SW-TRACE has better
PAPR performance and lower computational complexity.
Abstract: Amyloid aggregation of polypeptides is related to a
growing number of pathologic states known as amyloid disorders. In
recent years, blocking or reversing amyloid aggregation via the use of
small compounds are considered as two useful approaches in
hampering the development of these diseases. In this research, we
have compared the ability of several manganese-salen derivatives, as
synthetic compounds, and apigenin, as a natural flavonoid, to inhibit
of hen egg-white lysozyme (HEWL) aggregation, as an in vitro
model system.
Different spectroscopic analyses such as Thioflavin T (ThT) and
Anilinonaphthalene-8-sulfonic acid (ANS) fluorescence, Congo red
(CR) absorbance along with transmission electron microscopy were
used in this work to monitor the HEWL aggregation kinetic and
inhibition. Our results demonstrated that both type of compounds
were capable to prevent the formation of lysozyme amyloid
aggregation in vitro. In addition, our data indicated that synthetic
compounds had higher activity to inhibit of the β-sheet structures
relative to natural compound. Regarding the higher antioxidant
activities of the salen derivatives, it can be concluded that in addition
to aromatic rings of each of the compounds, the potent antioxidant
properties of salen derivatives contributes to lower lysozyme fibril
accumulation.
Abstract: Castor (Ricinus communis L.) is one of the important
non-edible oilseed crops having immense industrial and medicinal
value. Oil yield per unit area is the ultimate target in growing oilseed
plants and sowing date is one of the important factors which have a
clear role on production of active substances particularly in oilseeds.
This study was conducted to evaluate the effect of sowing date on the
seed and oil yield of castor in Central Anatolia of Turkey in 2011.
The field experiment was set up in a completely randomized block
design with three replications. Black Diamond-2 castor cultivar was
used as plant material. The treatment was four sowing dates of May
10, May 25, June 10, June 25. In this research; seed yield, oil content
and oil yield were investigated. Results showed that the effect of
different sowing dates were significant on all of characteristics. In
general; delayed sowing dates, resulted in decreased seed yield, oil
content and oil yield. The highest value of seed yield, oil content and
oil yield (respectively, 2523.7 kg ha-1, 51.18% and 1292.2 kg ha-1)
were obtained from the first sowing date (May 10) while the lowest
seed yield, oil content and oil yield (respectively, 1550 kg ha-1,
43.67%, 677.3 kg ha-1) were recorded from the latest sowing date
(June 25). Therefore, it can be concluded that early May could be
recommended as an appropriate sowing date in the studied location
and similar climates for achieved high oil yield of castor.
Abstract: Effect of blockage ratio on heat transfer from non-circular tube is studied experimentally. For doing this experiment a suction type low speed wind tunnel with test section dimension of 14×14×40 and velocity in rage of 7-20 m/s was designed. The blockage ratios varied between 1.5 to 7 and Reynolds number based on equivalent diameter varies in range of 7.5×103 to 17.5×103. The results show that by increasing blockage ratio from 1.5 to 7, drag coefficient of the cam shaped tube decreased about 55 percent. By increasing Reynolds number, Nusselt number of the cam shaped tube increases about 40 to 48 percent in all ranges of blockage ratios.
Abstract: In this paper, a fifth order propagator operators are proposed for estimating the Angles Of Arrival (AOA) of narrowband electromagnetic waves impinging on antenna array when its number of sensors is larger than the number of radiating sources.
The array response matrix is partitioned into five linearly dependent phases to construct the noise projector using five different propagators from non diagonal blocks of the spectral matrice of the received data; hence, five different estimators are proposed to estimate the angles of the sources. The simulation results proved the performance of the proposed estimators in the presence of white noise comparatively to high resolution eigen based spectra.
Abstract: This paper increases directivity and gain of Small Planar Dipole Antenna (SPDA) by using Symmetrical Pyramidal Block (SPB) which operates in X band at 11 GHz. The SPB consists four sides; each of which is metamaterial with Epsilon Negative Medium (ENG) and Epsilon Near-Zero (ENZ). The results simulated using the High Frequency Structure Simulator (HFSS) show that the SPB is capable of enhancing directivity and gain for the SPDA with maximum gain of 2.46 dB. The reflection coefficient is -13.7037 dB with narrow beam width.
Abstract: A hydroponic trial was carried out to investigate the effect of molybdenum (Mo) on uptake of phosphorus (P) in different rice cultivars. The experiment was conducted using a randomized complete-block design, with a split-plot arrangement of treatments and three replications. Four rates of Mo (0, 0.01, 0.1 and 1 mg L−1) and five cultivars (MR219, HASHEMI, MR232, FAJRE and MR253) provided the main and sub-plots, respectively. Interaction of molybdenum×variety was significant on shoot phosphorus uptake (p≤0.01). Highest and lowest shoot phosphorus uptake were seen in Mo3V3 (0.6% plant-1) and Mo0V3 (0.14% plant-1) treatments, respectively. Molybdenum did not have a significant effect on root phosphorus content. According to results, application of molybdenum has a synergistic effect on uptake of phosphorus by rice plants.
Abstract: The commercial sandcrete block makers in Nigeria use the same cement-sand mix ratio for sandcrete blocks production irrespective of the cement grade. Investigation revealed that the compressive strengths of hollow sandcrete blocks produced with Portland-limestone cement grade 42.5 are higher than the sandcrete blocks produced with cement grade 32.5. The use of stronger sandcrete blocks produced with cement grade 42.5 will ensure the construction of stronger buildings and other sandcrete blocks-based infrastructures and reduce the incessant failure of building and other sandcrete blocks-based infrastructures in Nigeria at no additional cost as both cement grades cost the same amount in Nigeria. It is recommended that the Standards Organisation of Nigeria should create grassroots awareness on the different cement grades in Nigeria and specify that Portland-limestone cement grade 42.5 be used for sandcrete blocks production.
Abstract: Ni-based catalysts with different amounts of Na as
promoter from 2 to 6 wt % were prepared by solution combustion
method. The catalytic activity was investigated in syngas methanation
reaction. Carbon oxides conversion and methane selectivity are greatly
influenced by sodium loading. Adding 2 wt% Na remarkably improves
catalytic activity and long-term stability, attributed to its smaller mean
NiO particle size, better distribution, and milder metal-support
interaction. However, excess addition of Na results in deactivation
distinctly due to the blockage of active sites.
Abstract: Imperial competitive algorithm (ICA) simulates a multi-agent algorithm. Each agent is like a kingdom has its country, and the strongest country in each agent is called imperialist, others are colony. Countries are competitive with imperialist which in the same kingdom by evolving. So this country will move in the search space to find better solutions with higher fitness to be a new imperialist. The main idea in this paper is using the peculiarity of ICA to explore the search space to solve the kinds of combinational problems. Otherwise, we also study to use the greed search to increase the local search ability. To verify the proposed algorithm in this paper, the experimental results of traveling salesman problem (TSP) is according to the traveling salesman problem library (TSPLIB). The results show that the proposed algorithm has higher performance than the other known methods.
Abstract: The stress-strain relationship of concrete under flexure is one of the essential parameters in assessing ultimate flexural strength capacity of RC beams. Currently, the concrete stress-strain curve in flexure is obtained by incorporating a constant scale-down factor of 0.85 in the uniaxial stress-strain curve. However, it was revealed that strain gradient would improve the maximum concrete stress under flexure and concrete stress-strain curve is strain gradient dependent. Based on the strain-gradient-dependent concrete stress-strain curve, the investigation of the combined effects of strain gradient and concrete strength on flexural strength of RC beams was extended to high strength concrete up to 100 MPa by theoretical analysis. As an extension and application of the authors’ previous study, a new flexural strength design method incorporating the combined effects of strain gradient and concrete strength is developed. A set of equivalent rectangular concrete stress block parameters is proposed and applied to produce a series of design charts showing that the flexural strength of RC beams are improved with strain gradient effect considered.
Abstract: Diesel vehicle should be equipped with emission after-treatment devices as NOx reduction catalyst and particulate filtersin order to meet more stringer diesel emission standard. Urea-SCR is being developed as the most efficient method of reducing NOx emissions in the after-treatment devices of diesel engines, and recent studies have begun to mount the Urea-SCR device for diesel passenger cars and light duty vehicles. In the present study, the effects of the mixer on the efficiency of urea-SCR System (i.e., NH3uni- formityindex (NH3 UI) is investigated by predicting the transport phenomena in the urea-SCR system. The three dimensional Eulerian-Lagrangian CFD simulationfor internal flow and spray characteristics in front of SCR is carried out by using STAR-CCM+ 7.06 code. In addition, the paper proposes a method to minimize the wall-wetting around the urea injector in order to prevent injector blocks caused by solid urea loading.
Abstract: In this paper, a multi-focus image fusion method using Spatial Frequency Measurements (SFM) and Wavelet Packet was proposed. The proposed fusion approach, firstly, the two fused images were transformed and decomposed into sixteen subbands using Wavelet packet. Next, each subband was partitioned into sub-blocks and each block was identified the clearer regions by using the Spatial Frequency Measurement (SFM). Finally, the recovered fused image was reconstructed by performing the Inverse Wavelet Transform. From the experimental results, it was found that the proposed method outperformed the traditional SFM based methods in terms of objective and subjective assessments.
Abstract: The main idea in this paper is using sequential pattern mining to find the information which is helpful for finding high performance solutions. By combining this information, it is defined as blocks. Using the blocks to generate artificial chromosomes (ACs) could improve the structure of solutions. Estimation of Distribution Algorithms (EDAs) is adapted to solve the combinatorial problems. Nevertheless many of these approaches are advantageous for this application, but only some of them are used to enhance the efficiency of application. Generating ACs uses patterns and EDAs could increase the diversity. According to the experimental result, the algorithm which we proposed has a better performance to solve the permutation flow-shop problems.