Abstract: In Ultra high-field MRI scanners (3T and higher),
parallel RF transmission techniques using multiple RF chains with
multiple transmit elements are a promising approach to overcome
the high-field MRI challenges in terms of inhomogeneity in the RF
magnetic field and SAR. However, mutual coupling between the
transmit array elements disturbs the desirable independent control of
the RF waveforms for each element. This contribution demonstrates
a 18 dB improvement of decoupling (isolation) performance due to
the very low output impedance of our 1 kW power amplifier.
Abstract: Measurement of the ultrasonic pulse velocity (UPV) is an important tool in diagnostic examination of concrete. In this method piezoelectric transducers are normally held in direct contact with the concrete surface. The current study aims to test the hypothesis that a preferential coupling effect might exist i.e. that the speed of sound measured depends on the couplant used. In this study, different coupling media of varying acoustic impedance were placed between the transducers and concrete samples made with constant aggregate content but with different compressive strengths. The preliminary results show that using coupling materials (both solid and a range of liquid substances) has an effect on the pulse velocity measured in a given concrete. The effect varies depending on the material used. The UPV measurements with solid coupling were higher than these from the liquid coupling at all strength levels. The tests using couplants generally recorded lower UPV values than the conventional test, except when carbon fiber composite was used, which retuned higher values. Analysis of variances (ANOVA) was performed to confirm that there are statistically significant differences between the measurements recorded using a conventional system and a coupled system.
Abstract: The aim of this study is to compare abused and normal male students in Tehran guidance schools with emphasis on the co-dependency of their mothers. The method of this study is based on survey method and comparison (Ex-Post Facto). The method of sampling is also multi-stage cluster. Accordingly, we did sampling from secondary schools of education and training in Tehran, including 12 schools with levels of first, second and third. Each of the schools represents the three – high, medium and low- economic and social conditions. In the following, three classes from every school and 20 students from each class were randomly selected. By (CTQ) abused and normal students were separated that 670 children were recognized as normal and 50 children as abused. Then, 50 children were randomly selected from normal group and compared with abused group. Using Spanned-Fischer Co-dependency Scale, we compared mothers of abused and normal students. The results showed that mothers of the abused children have higher co- dependency average comparing to the mothers of the normal children.
Abstract: Feedback is a vital element for improving student
learning in a simulation-based training as it guides and refines
learning through scaffolding. A number of studies in literature have
shown that students’ learning is enhanced when feedback is provided
with personalized tutoring that offers specific guidance and adapts
feedback to the learner in a one-to-one environment. Thus, emulating
these adaptive aspects of human tutoring in simulation provides an
effective methodology to train individuals. This paper presents the results of a study that investigated the
effectiveness of automating different types of feedback techniques
such as Knowledge-of-Correct-Response (KCR) and Answer-Until-
Correct (AUC) in software simulation for learning basic information
technology concepts. For the purpose of comparison, techniques like
simulation with zero or no-feedback (NFB) and traditional hands-on
(HON) learning environments are also examined. The paper presents the summary of findings based on quantitative
analyses which reveal that the simulation based instructional
strategies are at least as effective as hands-on teaching methodologies
for the purpose of learning of IT concepts. The paper also compares
the results of the study with the earlier studies and recommends
strategies for using feedback mechanism to improve students’
learning in designing and simulation-based IT training.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: In this paper, we present the design of the
super-ellipsoidal potential function (SEPF), that can be used for
autonomous collision avoidance of an unmanned aerial vehicle (UAV)
in a 3-dimensional space. In the design of SEPF, we have the
full control over the shape and size of the potential function. In
particular, we can adjust the length, width, height, and the amount
of flattening at the tips of the potential function so that the collision
avoidance motion vector generated from the potential function can
be adjusted accordingly. Based on the idea of the SEPF, we also
propose an approach for the local autonomy of a UAV for its collision
avoidance when the UAV is teleoperated by a human operator. In
our proposed approach, a teleoperated UAV can not only avoid
collision autonomously with other surrounding objects but also track
the operator’s control input as closely as possible. As a result, an
operator can always be in control of the UAV for his/her high-level
guidance and navigation task without worrying too much about
the UAVs collision avoidance while it is being teleoperated. The
effectiveness of the proposed approach is demonstrated through a
human-in-the-loop simulation of quadrotor UAV teleoperation using
virtual robot experimentation platform (v-rep) and Matlab programs.
Abstract: This paper presents the strategic development plan of
winged rockets WIRES (WInged REusable Sounding rocket) aiming
at unmanned suborbital winged rocket for demonstrating future fully
reusable space transportation technologies, such as aerodynamics,
Navigation, Guidance and Control (NGC), composite structure,
propulsion system, and cryogenic tanks etc., by universities in
collaboration with government and industries, as well as the past and
current flight test results.
Abstract: This paper presents the performance characteristics of
Darrieus-type vertical axis wind turbine (VAWT) with NACA airfoil
blades. The performance of Darrieus-type VAWT can be
characterized by torque and power. There are various parameters
affecting the performance such as chord length, helical angle, pitch
angle and rotor diameter. To estimate the optimum shape of Darrieustype
wind turbine in accordance with various design parameters, we
examined aerodynamic characteristics and separated flow occurring
in the vicinity of blade, interaction between flow and blade, and
torque and power characteristics derived from it. For flow analysis,
flow variations were investigated based on the unsteady RANS
(Reynolds-averaged Navier-Stokes) equation. Sliding mesh algorithm
was employed in order to consider rotational effect of blade. To
obtain more realistic results we conducted experiment and numerical
analysis at the same time for three-dimensional shape. In addition,
several parameters (chord length, rotor diameter, pitch angle, and
helical angle) were considered to find out optimum shape design and
characteristics of interaction with ambient flow. Since the NACA
airfoil used in this study showed significant changes in magnitude of
lift and drag depending on an angle of attack, the rotor with low drag,
long cord length and short diameter shows high power coefficient in
low tip speed ratio (TSR) range. On the contrary, in high TSR range,
drag becomes high. Hence, the short-chord and long-diameter rotor
produces high power coefficient. When a pitch angle at which airfoil
directs toward inside equals to -2° and helical angle equals to 0°,
Darrieus-type VAWT generates maximum power.
Abstract: In this research, students’ scientific attitude, computer anxiety, educational use of the Internet, academic achievement, and problematic use of the Internet are analyzed based on different variables (gender, parents’ educational level and daily access to the Internet). The research group involves 361 students from two middle schools which are located in the center of Konya. The “general survey method” is adopted in the research. In accordance with the purpose of the study, percentage, mean, standard deviation, independent samples t--‐test, ANOVA (variance) are employed in the study. A total of four scales are implemented. These four scales include a total of 13 sub-dimensions. The scores from these scales and their subscales are studied in terms of various variables. In the research, students’ scientific attitude, computer anxiety, educational use of the Internet, the problematic Internet use and academic achievement (gender, parent educational level, and daily access to the Internet) are investigated based on various variables and some significant relations are found.
Abstract: Aerobic dance has becoming a popular mode of
exercise especially among women due to its fun nature. With a catchy
music background and joyful dance steps, aerobic dancers would be
able to have fun while sweating out. Depending on its level of
aggressiveness, aerobic may also improve and maintain
cardiorespiratory fitness other than being a great tool for weight loss.
This study intends to prove that aerobic dance activity can bring the
same, if not better impacts on health than other types of
cardiovascular exercise such as jogging and cycling. The objective of
this study was to evaluate and identify the effect of six weeks aerobic
dance on cardiovascular fitness and weight loss among women. This
study, which was held in Seremban Fit Challenge, used a quasiexperimental
design. The subjects selected include a total of 14
women (n = 14) with age (32.4 years old ± 9.1), weight (65.93 kg ±
11.24) and height (165.36 ± 3.46) who joined the Seremban Fit
Challenge Season 13. The subjects were asked to join an aerobic
dance class with a duration of one hour for six weeks in a row. As for
the outcome, cardiovascular fitness was measured with a 1-mile run
test while any changes on weight were measured using the weighing
scale. The result showed that there was a significant difference
between pre and post-test for cardiovascular fitness when p = 0.02
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: The out-of-band impedance environment is considered
to be of paramount importance in engineering the in-band impedance
environment. Presenting the frequency independent and constant outof-
band impedances across the wide modulation bandwidth is
extremely important for reliable device characterization for future
wireless systems. This paper presents an out-of-band impedance
optimization scheme based on simultaneous engineering of
significant baseband components IF1 (twice the modulation
frequency) and IF2 (four times the modulation frequency) and higher
baseband components such as IF3 (six times the modulation
frequency) and IF4 (eight times the modulation frequency) to
engineer the in-band impedance environment. The investigations
were carried out on a 10W GaN HEMT device driven to deliver a
peak envelope power of approximately 40.5dBm under modulated
excitation. The presentation of frequency independent baseband
impedances to all the significant baseband components whilst
maintaining the optimum termination for fundamental tones as well
as reactive termination for 2nd harmonic under class-J mode of
operation has outlined separate optimum impedances for best
intermodulation (IM) linearity.
Abstract: Information technology has been gaining more and
more space whether in industry, commerce or even for personal use,
but the misuse of it brings harm to the environment and human health
as a result. Contribute to the sustainability of the planet is to
compensate the environment, all or part of what withdraws it. The
green computing also came to propose practical for use in IT in an
environmentally correct way in aid of strategic management and
communication. This work focuses on showing how a mobile
application can help businesses reduce costs and reduced
environmental impacts caused by its processes, through a case study
of a public company in Brazil.
Abstract: This first-attempt study revealed that decolorized
intermediates of azo dyes could act as redox mediators to assist
wastewater (WW) decolorization due to enhancement of
electron-transport phenomena. Electrochemical impedance spectra
indicated that hydroxyl and amino-substituent(s) were functional
group(s) as redox-mediator(s). As azo dyes are usually multiple
benzene-rings structured, their derived decolorized intermediates are
likely to play roles of electron shuttles due to lower barrier of energy
gap for electron shuttling. According to cyclic voltammetric profiles,
redox mediating characteristics of decolorized intermediates of azo
dyes (e.g., RBu171, RR198, RR141, RBk5) were clearly disclosed.
With supplementation of biodecolorized metabolites of RR141 and
198, decolorization performance of could be evidently augmented.
This study also suggested the optimal modes of microbial fuel cell
(MFC)-assisted WW decolorization would be plug-flow or batch
mode of operation with no mix. Single chamber-MFCs would be more
favourable than double chamber MFCs due to non-mixing contacting
reactor scheme for operation.
Abstract: In this paper, we introduce a flexible box erecting
machine (BEM) that swiftly and automatically transforms cardboard
into a three dimensional box. Recently, the parcel service and
home-shopping industries have grown rapidly, and there is an
increasing need for various box types to ship various products.
However, workers cannot fold thousands of boxes manually in a day.
As such, automatic BEMs are garnering greater attention. This study
takes equipment operation into consideration as well as mechanical
improvements in order to design a BEM that is able to outperform its
conventional counterparts. We analyzed six dispatching rules – First In
First Out (FIFO), Shortest Processing Time (SPT), Earliest Due Date
(EDD), Setup Avoidance, EDD + SPT, and EDD + Setup Avoidance –
to determine which one was most suitable for BEM operation.
Consequently, SPT and Setup Avoidance were found to be the most
critical rules, followed by EDD + Setup Avoidance, EDD + SPT,
EDD, and FIFO. This hierarchy was valid for both our conventional
BEM and our new flexible BEM from the viewpoint of processing
time. We believe that this research can contribute to flexible BEM
management, which has the potential to increase productivity and
convenience.
Abstract: A broadband wire monopole antenna loaded by inhomogeneous stack of annular dielectric ring resonators (DRRs) is proposed. The proposed antenna exhibits a broad impedance bandwidth from 3 to 30 GHz. This is achieved by adding an external step matching network at the antenna feed point. The matching network is comprised of three annular DRRs possessing different permittivity values and sharing the same axial over a finite ground plane. The antenna performance is characterized using full-wave EM simulation. Compared to previous-reported wire antennas with improved bandwidth achieved by DRRs, the proposed topology provides relatively compact realization and superior broadband performance.
Abstract: A myriad of environmental issues face the Nigerian
industrial region, resulting from; oil and gas production, mining,
manufacturing and domestic wastes. Amidst these, much effort has
been directed by stakeholders in the Nigerian oil producing regions,
because of the impacts of the region on the wider Nigerian economy.
Although collaborative environmental management has been noted as
an effective approach in managing environmental issues, little
attention has been given to the roles and practices of stakeholders in
effecting a collaborative environmental management framework for
the Nigerian oil-producing region. This paper produces a framework
to expand and deepen knowledge relating to stakeholders aspects of
collaborative roles in managing environmental issues in the Nigeria
oil-producing region. The knowledge is derived from analysis of
stakeholders’ practices – studied through multiple case studies using
document analysis. Selected documents of key stakeholders –
Nigerian government agencies, multi-national oil companies and host
communities, were analyzed. Open and selective coding was
employed manually during document analysis of data collected from
the offices and websites of the stakeholders. The findings showed
that the stakeholders have a range of roles, practices, interests, drivers
and barriers regarding their collaborative roles in managing
environmental issues. While they have interests for efficient resource
use, compliance to standards, sharing of responsibilities, generating
of new solutions, and shared objectives; there is evidence of major
barriers and these include resource allocation, disjointed policy,
ineffective monitoring, diverse socio- economic interests, lack of
stakeholders’ commitment and limited knowledge sharing. However,
host communities hold deep concerns over the collaborative roles of
stakeholders for economic interests, particularly, where government
agencies and multi-national oil companies are involved. With these
barriers and concerns, a genuine stakeholders’ collaboration is found
to be limited, and as a result, optimal environmental management
practices and policies have not been successfully implemented in the
Nigeria oil-producing region. A framework is produced that describes
practices that characterize collaborative environmental management
might be employed to satisfy the stakeholders’ interests. The
framework recommends critical factors, based on the findings, which
may guide a collaborative environmental management in the oil
producing regions. The recommendations are designed to re-define
the practices of stakeholders in managing environmental issues in the
oil producing regions, not as something wholly new, but as an
approach essential for implementing a sustainable environmental
policy. This research outcome may clarify areas for future research as
well as to contribute to industry guidance in the area of collaborative
environmental management.
Abstract: This study aims to establish function point process
based on stochastic distribution. In order to demonstrate effectiveness
of the study we present a case study that it applies suggested method
on an automotive electrical and electronics system software
development based on Monte Carlo Simulation. It is expected that the
result of this paper is used as guidance for establishing function point
process in organizations and tools for helping project managers make
decisions correctly.
Abstract: Strong anthropogenic impact has uncontrolled
consequences on the nature of the soil. Hence, up-to-date sustainable
methods of soil state improvement are essential. Investigators provide
the evidence that biochar can positively effects physical, chemical,
and biological soil properties and the abundance of mycorrhizal fungi
which are in the focus of this study. The main aim of the present
investigation is to demonstrate the effect of two types of plant growth
promoting bacteria (PGPB) inoculums along with the beech wood
biochar and mineral N additives on mycorrhizal colonization.
Experiment has been set up in laboratory conditions with containers
filled with arable soil from the protection zone of the main water
source “Brezova nad Svitavou”. Lactuca sativa (lettuce) has been
selected as a model plant. Based on the obtained data, it can be
concluded that mycorrhizal colonization increased as the result of
combined influence of biochar and PGPB inoculums amendment. In
addition, correlation analyses showed that the numbers of main
groups of cultivated bacteria were dependent on the degree of
mycorrhizal colonization.
Abstract: Strong anthropogenic impact has uncontrolled
consequences on the nature of the soil. Hence, up-to-date sustainable
methods of soil state improvement are essential. Investigators provide
the evidence that biochar can positively effects physical, chemical,
and biological soil properties and the abundance of mycorrhizal fungi
which are in the focus of this study. The main aim of the present
investigation is to demonstrate the effect of two types of plant growth
promoting bacteria (PGPB) inoculums along with the beech wood
biochar and mineral N additives on mycorrhizal colonization.
Experiment has been set up in laboratory conditions with containers
filled with arable soil from the protection zone of the main water
source “Brezova nad Svitavou”. Lactuca sativa (lettuce) has been
selected as a model plant. Based on the obtained data, it can be
concluded that mycorrhizal colonization increased as the result of
combined influence of biochar and PGPB inoculums amendment. In
addition, correlation analyses showed that the numbers of main
groups of cultivated bacteria were dependent on the degree of
mycorrhizal colonization.