Abstract: The dynamics of Min proteins plays a center role in
accurate cell division. Although the nucleoids may presumably play
an important role in prokaryotic cell division, there is a lack of
models to account for its participation. In this work, we apply the
lattice Boltzmann method to investigate protein oscillation based on a
mesoscopic model that takes into account the nucleoid-s role. We
found that our numerical results are in reasonably good agreement
with the previous experimental results On comparing with the other
computational models without the presence of nucleoids, the
highlight of our finding is that the local densities of MinD and MinE
on the cytoplasmic membrane increases, especially along the cell
width, when the size of the obstacle increases, leading to a more
distinct cap-like structure at the poles. This feature indicated the
realistic pattern and reflected the combination of Min protein
dynamics and nucleoid-s role.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: Isobaric vapor-liquid equilibrium measurements are
reported for binary mixture of 2-Methyltetrahydrofuran and Cumene
at 97.3 kPa. The data were obtained using a vapor recirculating type
(modified Othmer's) equilibrium still. The mixture shows slight
negative deviation from ideality. The system does not form an
azeotrope. The experimental data obtained in this study are
thermodynamically consistent according to the Herington test. The
activity coefficients have been satisfactorily correlated by means of
the Margules, and NRTL equations. Excess Gibbs free energy has
been calculated from the experimental data. The values of activity
coefficients have also been obtained by the UNIFAC group
contribution method.
Abstract: Water is the main component of biological processes.
Water management is important to obtain higher productivity. In this
study, some of the yield components were investigated together with
different drought levels. Four chickpea genotypes (CDC Frontier,
CDC Luna, Sawyer and Sierra) were grown in pots with 3 different
irrigation levels (a dose of 17.5 ml, 35 ml and 70 ml for each pot per
day) after three weeks from sowing. In the research, flowering, pod
set, pod per plant, fertile pod, double seed/pod, stem diameter, plant
weight, seed per plant, 1000 seed weight, seed diameter, vegetation
length and weekly plant height were measured. Consequently,
significant differences were observed on all the investigated
characteristics owing to genotypes (except double seed/pod and stem
diameter), water levels (except first pod, seed weight and height on
3rd week) and genotype x water level interaction (except first pod,
double seed/pod, seed weight and height).
Abstract: This paper presents the possibilities of using Weibull statistical distribution in modeling the distribution of defects in ERP systems. There follows a case study, which examines helpdesk records of defects that were reported as the result of one ERP subsystem upgrade. The result of the applied modeling is in modeling the reliability of the ERP system from a user perspective with estimated parameters like expected maximum number of defects in one day or predicted minimum of defects between two upgrades. Applied measurement-based analysis framework is proved to be suitable in predicting future states of the reliability of the observed ERP subsystems.
Abstract: In this paper a novel method for multiple one dimensional real valued sinusoidal signal frequency estimation in the presence of additive Gaussian noise is postulated. A computationally simple frequency estimation method with efficient statistical performance is attractive in many array signal processing applications. The prime focus of this paper is to combine the subspace-based technique and a simple peak search approach. This paper presents a variant of the Propagator Method (PM), where a collaborative approach of SUMWE and Propagator method is applied in order to estimate the multiple real valued sine wave frequencies. A new data model is proposed, which gives the dimension of the signal subspace is equal to the number of frequencies present in the observation. But, the signal subspace dimension is twice the number of frequencies in the conventional MUSIC method for estimating frequencies of real-valued sinusoidal signal. The statistical analysis of the proposed method is studied, and the explicit expression of asymptotic (large-sample) mean-squared-error (MSE) or variance of the estimation error is derived. The performance of the method is demonstrated, and the theoretical analysis is substantiated through numerical examples. The proposed method can achieve sustainable high estimation accuracy and frequency resolution at a lower SNR, which is verified by simulation by comparing with conventional MUSIC, ESPRIT and Propagator Method.
Abstract: Properties of cement pastes with fine-ground ceramics
used as an alternative binder replacing Portland cement up to 20% of
its mass are investigated. At first, the particle size distribution of
cement and fine-ground ceramics is measured using laser analyser.
Then, the material properties are studied in the early hardening
period up to 28 days. The hydration process of studied materials is
monitored by electrical conductivity measurement using TDR
sensors. The changes of materials- structures within the hardening are
observed using pore size distribution measurement. The compressive
strength measurements are done as well. Experimental results show
that the replacement of Portland cement by fine-ground ceramics in
the amount of up to 20% by mass is acceptable solution from the
mechanical point of view. One can also assume similar physical
properties of designed materials to the reference material with only
Portland cement as binder.
Abstract: This paper presents the speed regulation scheme of a small brushless dc motor (BLDC motor) with trapezoidal back-emf consideration. The proposed control strategy uses the proportional controller in which the proportional gain, kp, is appropriately adjusted by using genetic algorithms. As a result, the proportional control can perform well in order to compensate the BLDC motor with load disturbance. This confirms that the proposed speed regulation scheme gives satisfactory results.
Abstract: A water surface slope limiting scheme is tested and
compared with the water depth slope limiter for the solution of one
dimensional shallow water equations with bottom slope source term.
Numerical schemes based on the total variation diminishing Runge-
Kutta discontinuous Galerkin finite element method with slope
limiter schemes based on water surface slope and water depth are
used to solve one-dimensional shallow water equations. For each
slope limiter, three different Riemann solvers based on HLL, LF, and
Roe flux functions are used. The proposed water surface based slope
limiter scheme is easy to implement and shows better conservation
property compared to the slope limiter based on water depth. Of the
three flux functions, the Roe approximation provides the best results
while the LF function proves to be least suitable when used with
either slope limiter scheme.
Abstract: Renewable water resources are crucial production
variables in arid and semi-arid regions where intensive agriculture is
practiced to meet ever-increasing demand for food and fiber. This is
crucial for the Dez and Moghan command areas where water delivery
problems and adverse environmental issues are widespread. This
paper aims to identify major problems areas using on-farm surveys of
200 farmers, agricultural extensionists and water suppliers which was
complemented by secondary data and field observations during 2010-
2011 cultivating season. The SPSS package was used to analyze and
synthesis data. Results indicated inappropriate canal operations in
both schemes, though there was no unanimity about the underlying
causes. Inequitable and inflexible distribution was found to be rooted
in deficient hydraulic structures particularly in the main and
secondary canals. The inadequacy and inflexibility of water
scheduling regime was the underlying causes of recurring pest and
disease spread which often led to the decline of crop yield and
quality, although these were not disputed, the water suppliers were
not prepared to link with the deficiencies in the operation of the main
and secondary canals. They rather attributed these to the prevailing
salinity; alkalinity, water table fluctuations and leaching of the
valuable agro-chemical inputs from the plants- route zone with farreaching
consequences. Examples of these include the pollution of
ground and surface resources due to over-irrigation at the farm level
which falls under the growers- own responsibility. Poor irrigation
efficiency and adverse environmental problems were attributed to
deficient and outdated farming practices that were in turn rooted in
poor extension programs and irrational water charges.
Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: Since DVB-RCS has been successively implemented, the mobile communication on the multi-beam satellite communication is attractive attention. And the DVB-RCS standard sets up to support mobility of a RCST. In the case of the spot-beam satellite system, the received signal strength does not differ largely between the center and the boundary of the beam. Thus, the RSS based handoff detection algorithm is not benefit to the satellite system as a terrestrial system. Therefore we propose an Adaptive handoff detection algorithm based on RCST mobility information. Our handoff detection algorithm not only can be used as centralized handoff detection algorithm but also removes uncertainties of handoff due to the variation of RSS. Performances were compared with RSS based handoff algorithm. Simulation results show that the proposed handoff detection algorithm not only achieved better handoff and link degradation rate, but also achieved better forward link spectral efficiency.
Abstract: ICT and supply chain management (SCM) are two
notions, which have attracted much attention among both
academicians and practitioners during the last decade. However, the
discussion of the relationship between the two notions has been
limited and fragmented. In this paper, we will present a summary of
the discussion of ICT components and SCM on an extensive
literature review. Then, we will discuss the interrelation between ICT
and SCM from some major components and applications of ICT
perspective. After all, we can introduce e-SCM concept, that arisen
recently in management literature, in order to cover the whole topic.
The authors look at all of the major components of electronic supply
chain management and demonstrate that the future holds tremendous
opportunity for those firms that take advantage of all of its
possibilities.
Abstract: In this presentation, we discuss the use of information technologies in the area of special education for teaching individuals with learning disabilities. Application software which was developed for this purpose is used to demonstrate the applicability of a database integrated information processing system to alleviate the burden of educators. The software allows the preparation of individualized education programs based on the predefined objectives, goals and behaviors.
Abstract: Today many countries have the ambitious purposes of long-term and continuous development: constant growth of competitiveness, maintenance of a high standard of living of the population, leadership in the world market. One of the best possible ways of achievement of these purposes is a transition of the countries to innovative economy. The paper presents the analyses of problems of forming of innovative receptivity to innovations and creation of «innovative society». Creation of an innovative culture in a society and increase of the level of prestige of innovative activity are the best ways of developing of innovative processes. The base of the analysis is a comparing of Russia and different developed countries according to the level of some indictors of innovative activity.1
Abstract: Development, calibration and validation of a threedimensional
model of the Legform impactor for pedestrian crash with
bumper are presented. Lower limb injury is becoming an increasingly
important concern in vehicle safety for both occupants and
pedestrians. In order to prevent lower extremity injuries to a
pedestrian when struck by a car, it is important to elucidate the
loadings from car front structures on the lower extremities and the
injury mechanism caused by these loadings. An impact test
procedure with a legform addressing lower limb injuries in car
pedestrian accidents has been proposed by EEVC/WG17. In this
study a modified legform impactor is introduced and validated
against EEVC/WG17 criteria. The finite element model of this
legform is developed using LS-DYNA software. Total mass of
legform impactor is 13.4 kg.Technical specifications including the
mass and location of the center of gravity and moment of inertia
about a horizontal axis through the respective centre of gravity in
femur and tibia are determined. The obtained results of legform
impactor static and dynamic tests are as specified in the
EEVC/WG17.
Abstract: In the analysis of structures, the nonlinear effects due to large displacement, large rotation and materially-nonlinear are very important and must be considered for the reliable analysis. The non-linear fmite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of fmite element code using the standard Galerkin weighted residual formulation. Two-dimensional plane stress model was carried out to present the shear wall response. Total Lagangian formulation, which is computationally more effective, is used in the formulation of stiffness matrices and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The details of the program formulation are highlighted and the results of the analyses are presented, along with a comparison of the response of the structure with Ansys software results. The presented model in this paper can be developed for nonlinear analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: this article conducts a research about the relationship between cash dividend policy and enterprise value based on the data coming from the A-share listed companies over period 2005-2009. In conclusion, the enterprise value has a negative correlation with the incremental and the degressive cash dividend per share, and has a positive correlation with the stable cash dividend per share.
Abstract: In the paper we presented the possibility of application
collagen gels with active principle-s from marine algae extract and chlorhexidine salt in dental medicine. The hydro-alcoholic extracts
from marine algae have been used as they have been obtained. The extracts from marine algae and chlorhexidine salt (digluconate) are
incorporated in type I non-denatured fibrillar collagen matrixes. In order to obtain therapeutic effects at nanostructure level, it is important to know the rheological characteristics of the relevant mixtures of collagen gels and extracts from marine algae selected for use. In this survey we have studied mixtures made of non-denatured
fibrillar collagen hydro-gels where different concentrations of marine
algae have been incorporated. Based on the data obtained for the
shearing tensions, we have traced the rheograms – the diagrams for shearing tensions depending on the shearing speed values – from
which we have calculated the apparent viscosities as ratios between shearing tension and speed values, which have been figured in
relation to the shearing speed values, with a view to levelling
dependency.
Abstract: This work presents a new algorithm based on a combination of fuzzy (FUZ), Dynamic Programming (DP), and Genetic Algorithm (GA) approach for capacitor allocation in distribution feeders. The problem formulation considers two distinct objectives related to total cost of power loss and total cost of capacitors including the purchase and installation costs. The novel formulation is a multi-objective and non-differentiable optimization problem. The proposed method of this article uses fuzzy reasoning for sitting of capacitors in radial distribution feeders, DP for sizing and finally GA for finding the optimum shape of membership functions which are used in fuzzy reasoning stage. The proposed method has been implemented in a software package and its effectiveness has been verified through a 9-bus radial distribution feeder for the sake of conclusions supports. A comparison has been done among the proposed method of this paper and similar methods in other research works that shows the effectiveness of the proposed method of this paper for solving optimum capacitor planning problem.