Abstract: This study is concerned with the investigation of the
suitability of several empirical and semi-empirical drying models
available in the literature to define drying behavior of viscose yarn
bobbins. For this purpose, firstly, experimental drying behaviour of
viscose bobbins was determined on an experimental dryer setup
which was designed and manufactured based on hot-air bobbin
dryers used in textile industry. Afterwards, drying models considered
were fitted to the experimentally obtained moisture ratios. Drying
parameters were drying temperature and bobbin diameter. The fit
was performed by selecting the values for constants in the models in
such a way that these values make the sum of the squared differences
between the experimental and the model results for moisture ratio
minimum. Suitability of fitting was specified as comparing the
correlation coefficient, standard error and mean square deviation.
The results show that the most appropriate model in describing the
drying curves of viscose bobbins is the Page model.
Abstract: As in today's semiconductor industries test costs can make up to 50 percent of the total production costs, an efficient test error detection becomes more and more important. In this paper, we present a new machine learning approach to test error detection that should provide a faster recognition of test system faults as well as an improved test error recall. The key idea is to learn a classifier ensemble, detecting typical test error patterns in wafer test results immediately after finishing these tests. Since test error detection has not yet been discussed in the machine learning community, we define central problem-relevant terms and provide an analysis of important domain properties. Finally, we present comparative studies reflecting the failure detection performance of three individual classifiers and three ensemble methods based upon them. As base classifiers we chose a decision tree learner, a support vector machine and a Bayesian network, while the compared ensemble methods were simple and weighted majority vote as well as stacking. For the evaluation, we used cross validation and a specially designed practical simulation. By implementing our approach in a semiconductor test department for the observation of two products, we proofed its practical applicability.
Abstract: Testing is an activity that is required both in the
development and maintenance of the software development life cycle
in which Integration Testing is an important activity. Integration
testing is based on the specification and functionality of the software
and thus could be called black-box testing technique. The purpose of
integration testing is testing integration between software
components. In function or system testing, the concern is with overall
behavior and whether the software meets its functional specifications
or performance characteristics or how well the software and
hardware work together. This explains the importance and necessity
of IT for which the emphasis is on interactions between modules and
their interfaces. Software errors should be discovered early during
IT to reduce the costs of correction. This paper introduces a new type
of integration error, presenting an overview of Integration Testing
techniques with comparison of each technique and also identifying
which technique detects what type of error.
Abstract: Recently, a model multi-agent e-commerce system based on mobile buyer agents and transfer of strategy modules was proposed. In this paper a different approach to code mobility is introduced, where agent mobility is replaced by local agent creation supplemented by similar code mobility as in the original proposal. UML diagrams of agents involved in the new approach to mobility and the augmented system activity diagram are presented and discussed.
Abstract: In this paper we discuss the problems of the long-term management policy of Lake Peipsi and the roles of natural and anthropogenic factors in the ecological state of the lake. The reduction of the pollution during the last 15 years could not give significant changes of the chemical composition of the water, what implicates the essential role that natural factors have on the ecological state of lake. One of the most important factors having impact on the hydrochemical cycles and ecological state is the hydrological regime which is clearly expressed in L. Peipsi. The absence on clear interrelations of climate cycles and nutrients suggest that complex abiotic and biotic interactions, which take place in the lake ecosystem, plays a significant role in the matter circulation mechanism within lake.
Abstract: Inter-organizational Workflow (IOW) is commonly
used to support the collaboration between heterogeneous and
distributed business processes of different autonomous organizations
in order to achieve a common goal. E-government is considered as an
application field of IOW. The coordination of the different
organizations is the fundamental problem in IOW and remains the
major cause of failure in e-government projects. In this paper, we
introduce a new coordination model for IOW that improves the
collaboration between government administrations and that respects
IOW requirements applied to e-government. For this purpose, we
adopt a Multi-Agent approach, which deals more easily with interorganizational
digital government characteristics: distribution,
heterogeneity and autonomy. Our model integrates also different
technologies to deal with the semantic and technologic
interoperability. Moreover, it conserves the existing systems of
government administrations by offering a distributed coordination
based on interfaces communication. This is especially applied in
developing countries, where administrations are not necessary
equipped with workflow systems. The use of our coordination
techniques allows an easier migration for an e-government solution
and with a lower cost. To illustrate the applicability of the proposed
model, we present a case study of an identity card creation in Tunisia.
Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: Large scale systems such as computational Grid is
a distributed computing infrastructure that can provide globally
available network resources. The evolution of information processing
systems in Data Grid is characterized by a strong decentralization of
data in several fields whose objective is to ensure the availability and
the reliability of the data in the reason to provide a fault tolerance
and scalability, which cannot be possible only with the use of the
techniques of replication. Unfortunately the use of these techniques
has a height cost, because it is necessary to maintain consistency
between the distributed data. Nevertheless, to agree to live with
certain imperfections can improve the performance of the system by
improving competition. In this paper, we propose a multi-layer protocol
combining the pessimistic and optimistic approaches conceived
for the data consistency maintenance in large scale systems. Our
approach is based on a hierarchical representation model with tree
layers, whose objective is with double vocation, because it initially
makes it possible to reduce response times compared to completely
pessimistic approach and it the second time to improve the quality
of service compared to an optimistic approach.
Abstract: The building sector is the largest energy consumer and
CO2 emitter in the European Union (EU) and therefore the active
reduction of energy consumption and elimination of energy wastage
are among the main goals in it. Healthy housing and energy
efficiency are affected by many factors which set challenges to
monitoring, control and research of indoor air quality (IAQ) and
energy consumption, especially in old buildings. These challenges
include measurement and equipment costs, for example.
Additionally, the measurement results are difficult to interpret and
their usage in the ventilation control is also limited when taking into
account the energy efficiency of housing at the same time. The main
goal of this study is to develop a cost-effective building monitoring
and control system especially for old buildings. The starting point or
keyword of the development process is a wireless system; otherwise
the installation costs become too high. As the main result, this paper
describes an idea of a wireless building monitoring and control
system. The first prototype of the system has been installed in 10
residential buildings and in 10 school buildings located in the City of
Kuopio, Finland.
Abstract: Nowadays, butyl acetate, a pineapple flavor has been applied widely in food, beverage, cosmetic and pharmaceutical industries. In this study, Butyl acetate, a flavor ester was successfully synthesized via green synthesis of enzymatic reaction route. Commercial immobilized lipase from Rhizomucor miehei (Lipozyme RMIM) was used as biocatalyst in the esterification reaction between acetic acid and butanol. Various reaction parameters such as reaction time (RT), temperature (T) and amount of enzyme (E) were chosen to optimize the reaction synthesis in solvent-free system. The optimum condition to produce butyl acetate was at reaction time (RT), 18 hours; temperature (T), 37°C and amount of enzyme, 25 % (w/w of total substrate). Analysis of yield showed that at optimum condition, >78 % of butyl acetate was produced. The product was confirmed as butyl acetate from FTIR analysis whereby the presence of an ester group was observed at wavenumber of 1742 cm-1.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: Detection of squirrel cage induction motor (SCIM) broken bars has long been an important but difficult job in the detection area of motor faults. Early detection of this abnormality in the motor would help to avoid costly breakdowns. A new detection method based on particle swarm optimization (PSO) is presented in this paper. Stator current in an induction motor will be measured and characteristic frequency components of faylted rotor will be detected by minimizing a fitness function using pso. Supply frequency and side band frequencies and their amplitudes can be estimated by the proposed method. The proposed method is applied to a faulty motor with one and two broken bars in different loading condition. Experimental results prove that the proposed method is effective and applicable.
Abstract: This research investigates the suitability of fuel oil in
improving gypseous soil. A detailed laboratory tests were carried-out
on two soils (soil I with 51.6% gypsum content, and soil II with
26.55%), where the two soils were obtained from Al-Therthar site
(Al-Anbar Province-Iraq).
This study examines the improvement of soil properties using the
gypsum material which is locally available with low cost to minimize
the effect of moisture on these soils by using the fuel oil. This study
was conducted on two models of the soil gypsum, from the Tharthar
area. The first model was sandy soil with Gypsum content of (51.6%)
and the second is clayey soil and the content of Gypsum is (26.55%).
The program included tests measuring the permeability and
compressibility of the soil and their collapse properties. The shear
strength of the soil and the amounts of weight loss of fuel oil due to
drying had been found. These tests have been conducted on the
treated and untreated soils to observe the effect of soil treatment on
the engineering properties when mixed with varying degrees of fuel
oil with the equivalent of the water content.
The results showed that fuel oil is a good material to modify the
basic properties of the gypseous soil of collapsibility and
permeability, which are the main problems of this soil and retained
the soil by an appropriate amount of the cohesion suitable for
carrying the loads from the structure.
Abstract: This paper provides a framework in order to
incorporate reliability issue as a sign of disruption in distribution
systems and partial covering theory as a response to limitation in
coverage radios and economical preferences, simultaneously into the
traditional literatures of capacitated facility location problems. As a
result we develop a bi-objective model based on the discrete
scenarios for expected cost minimization and demands coverage
maximization through a three echelon supply chain network by
facilitating multi-capacity levels for provider side layers and
imposing gradual coverage function for distribution centers (DCs).
Additionally, in spite of objectives aggregation for solving the model
through LINGO software, a branch of LP-Metric method called Min-
Max approach is proposed and different aspects of corresponds
model will be explored.
Abstract: The customer satisfaction for textile sector carries
great importance like the customer satisfaction for other sectors
carry. Especially, if it is considered that gaining new customers
create four times more costs than protecting existing customers from
leaving, it can be seen that the customer satisfaction plays a great
role for the firms. In this study the affecting independent variables of
customer satisfaction are chosen as brand image, perceived service
quality and perceived product quality. By these independent
variables, it is investigated that if any differences exist in perception
of customer satisfaction according to the Turkish textile consumers in
the view of gender. In data analysis of this research the SPSS
program is used.
Abstract: This paper explains how mobile learning assures sustainable e-education for multicultural group of students. This paper reports the impact of mobile learning on distance education in multicultural environment. The emergence of learning technologies through CD, internet, and mobile is increasingly adopted by distance institutes for quick delivery and cost-effective purposes. Their sustainability is conditioned by the structure of learners as well as the teaching community. The experimental study was conducted among the distant learners of Vinayaka Missions University located at Salem in India. Students were drawn from multicultural environment based on different languages, religions, class and communities. During the mobile learning sessions, the students, who are divided on language, religion, class and community, were dominated by play impulse rather than study anxiety or cultural inhibitions. This study confirmed that mobile learning improved the performance of the students despite their division based on region, language or culture. In other words, technology was able to transcend the relative deprivation in the multicultural groups. It also confirms sustainable e-education through mobile learning and cost-effective system of instruction. Mobile learning appropriates the self-motivation and play impulse of the young learners in providing sustainable e-education to multicultural social groups of students.
Abstract: In this article, we present a web server based solution
for implementing a system for intelligent navigation. In this solution
we use real time collected data and traffic history to establish the best
route for navigation. This is a low cost solution that is easily to
implement and extend. There is no need any infrastructure at road
network level except only a device that collect data about traffic in
key road crossing. The presented solution creates a strong base for
traffic pursuit and offers an infrastructure for navigation applications.
Abstract: Electronics Products that achieve high levels of integrated communications, computing and entertainment, multimedia features in small, stylish and robust new form factors are winning in the market place. Due to the high costs that an industry may undergo and how a high yield is directly proportional to high profits, IC (Integrated Circuit) manufacturers struggle to maximize yield, but today-s customers demand miniaturization, low costs, high performance and excellent reliability making the yield maximization a never ending research of an enhanced assembly process. With factors such as minimum tolerances, tighter parameter variations a systematic approach is needed in order to predict the assembly process. In order to evaluate the quality of upcoming circuits, yield models are used which not only predict manufacturing costs but also provide vital information in order to ease the process of correction when the yields fall below expectations. For an IC manufacturer to obtain higher assembly yields all factors such as boards, placement, components, the material from which the components are made of and processes must be taken into consideration. Effective placement yield depends heavily on machine accuracy and the vision of the system which needs the ability to recognize the features on the board and component to place the device accurately on the pads and bumps of the PCB. There are currently two methods for accurate positioning, using the edge of the package and using solder ball locations also called footprints. The only assumption that a yield model makes is that all boards and devices are completely functional. This paper will focus on the Monte Carlo method which consists in a class of computational algorithms (information processed algorithms) which depends on repeated random samplings in order to compute the results. This method utilized in order to recreate the simulation of placement and assembly processes within a production line.
Abstract: Microwave heating process has been developed about sixty years while measurement system has also progressed. Because of irradiation of high frequency of microwave, researchers have been utilized many costly technical instrument measuring parameters to evaluate the performance of microwave heating system. Therefore, this paper is intended to present an easier and feasible efficiency measurement method. It can help inspecting efficiency of microwave heating system with good accuracy, while the method can also give reference to optimizing procedure for microwave heating system for various load material
Abstract: In competitive electricity markets all over the world, an adoption of suitable transmission pricing model is a problem as transmission segment still operates as a monopoly. Transmission pricing is an important tool to promote investment for various transmission services in order to provide economic, secure and reliable electricity to bulk and retail customers. The nodal pricing based on SRMC (Short Run Marginal Cost) is found extremely useful by researchers for sending correct economic signals. The marginal prices must be determined as a part of solution to optimization problem i.e. to maximize the social welfare. The need to maximize the social welfare subject to number of system operational constraints is a major challenge from computation and societal point of views. The purpose of this paper is to present a nodal transmission pricing model based on SRMC by developing new mathematical expressions of real and reactive power marginal prices using GA-Fuzzy based optimal power flow framework. The impacts of selecting different social welfare functions on power marginal prices are analyzed and verified with results reported in literature. Network revenues for two different power systems are determined using expressions derived for real and reactive power marginal prices in this paper.