Abstract: This paper proposes a Wavelength Division
Multiplexing (WDM) technology based Storage Area Network
(SAN) for all type of Disaster recovery operation. It considers
recovery when all paths failure in the network as well as the main
SAN site failure also the all backup sites failure by the effect of
natural disasters such as earthquakes, fires and floods, power outage,
and terrorist attacks, as initially SAN were designed to work within
distance limited environments[2]. Paper also presents a NEW PATH
algorithm when path failure occurs. The simulation result and
analysis is presented for the proposed architecture with performance
consideration.
Abstract: The optimal operation of proton exchange membrane fuel cell (PEMFC) requires good water management which is presented under two forms vapor and liquid. Moreover, fuel cells have to reach higher output require integration of some accessories which need electrical power. In order to analyze fuel cells operation and different species transport phenomena a biphasic mathematical model is presented by governing equations set. The numerical solution of these conservation equations is calculated by Matlab program. A multi-criteria optimization with weighting between two opposite objectives is used to determine the compromise solutions between maximum output and minimal stack size. The obtained results are in good agreement with available literature data.
Abstract: According to the mobility of the satellite network nodes and the characteristic of management domain dynamic partition in the satellite network, the login and logout mechanism of the satellite network dynamic management domain partition was proposed in the paper. In the mechanism, a ground branch-station sends the packets of login broadcasting to satellites in view. After received the packets, the SNMP agents on the satellites adopt link-delay test to respond. According to the mechanism, the SNMP primitives were extended, and the new added primitives were as follows: broadcasting, login, login confirmation,delay_testing, test responses, and logout. The definition of primitives, which followed RFC1157 criterion, could be encoded by the BER coding. The policy of the dynamic management domain partition on the basis of the login and logout mechanism, which was supported by the SNMP protocol, was realized by the design of the extended primitives.
Abstract: Nowadays due to globalization of economy and
competition environment, innovation and technology plays key role
at creation of wealth and economic growth of countries. In fact
prompt growth of practical and technologic knowledge may results in
social benefits for countries when changes into effective innovation.
Considering the importance of innovation for the development of
countries, this study addresses the radical technological innovation
introduced by nanopapers at different stages of producing paper
including stock preparation, using authorized additives, fillers and
pigments, using retention, calender, stages of producing conductive
paper, porous nanopaper and Layer by layer self-assembly. Research
results show that in coming years the jungle related products will lose
considerable portion of their market share, unless embracing radical
innovation. Although incremental innovations can make this industry
still competitive in mid-term, but to have economic growth and
competitive advantage in long term, radical innovations are
necessary. Radical innovations can lead to new products and
materials which their applications in packaging industry can produce
value added. However application of nanotechnology in this industry
can be costly, it can be done in cooperation with other industries to
make the maximum use of nanotechnology possible. Therefore this
technology can be used in all the production process resulting in the
mass production of simple and flexible papers with low cost and
special properties such as facility at shape, form, easy transportation,
light weight, recovery and recycle marketing abilities, and sealing.
Improving the resistance of the packaging materials without reducing
the performance of packaging materials enhances the quality and the
value added of packaging. Improving the cellulose at nano scale can
have considerable electron optical and magnetic effects leading to
improvement in packaging and value added. Comparing to the
specifications of thermoplastic products and ordinary papers,
nanopapers show much better performance in terms of effective
mechanical indexes such as the modulus of elasticity, tensile strength,
and strain-stress. In densities lower than 640 kgm -3, due to the
network structure of nanofibers and the balanced and randomized
distribution of NFC in flat space, these specifications will even
improve more. For nanopapers, strains are 1,4Gpa, 84Mpa and 17%,
13,3 Gpa, 214Mpa and 10% respectively. In layer by layer self
assembly method (LbL) the tensile strength of nanopaper with Tio3
particles and Sio2 and halloysite clay nanotube are 30,4 ±7.6Nm/g
and 13,6 ±0.8Nm/g and 14±0.3,3Nm/g respectively that fall within
acceptable range of similar samples with virgin fiber. The usage of
improved brightness and porosity index in nanopapers can create
more competitive advantages at packaging industry.
Abstract: Personnel protection devices are cardinal in safety hazard applications. They are widely used in home, office and in industry environments to reduce the risk of lethal shock to human being and equipment safety. This paper briefly reviews various personnel protection devices also describes the basic working principle of conventional ground fault circuit interrupter (GFCI) or ground fault isolator (GFI), its disadvantages and ways to overcome the disadvantages with solid-state relay (SSR) based GFI with ultrafast response up on fault implemented in printed circuit board. This solid state GFI comprises discrete MOSFET based alternating current (AC) switches, linear optical amplifier, photovoltaic isolator and sense resistor. In conventional GFI, current transformer is employed as a sensing element to detect the difference in current flow between live and neutral conductor. If there is no fault in equipment powered through GFI, due to insulation failure of internal wires and windings of motors, both live and neutral currents will be equal in magnitude and opposite in phase.
Abstract: This paper presents a comparison of metaheuristic
algorithms, Genetic Algorithm (GA) and Ant Colony Optimization
(ACO), in producing freeman chain code (FCC). The main problem
in representing characters using FCC is the length of the FCC
depends on the starting points. Isolated characters, especially the
upper-case characters, usually have branches that make the traversing
process difficult. The study in FCC construction using one
continuous route has not been widely explored. This is our
motivation to use the population-based metaheuristics. The
experimental result shows that the route length using GA is better
than ACO, however, ACO is better in computation time than GA.
Abstract: On the basis of the linearized Phillips-Herffron model of a single-machine power system, a novel method for designing unified power flow controller (UPFC) based output feedback controller is presented. The design problem of output feedback controller for UPFC is formulated as an optimization problem according to with the time domain-based objective function which is solved by iteration particle swarm optimization (IPSO) that has a strong ability to find the most optimistic results. To ensure the robustness of the proposed damping controller, the design process takes into account a wide range of operating conditions and system configurations. The simulation results prove the effectiveness and robustness of the proposed method in terms of a high performance power system. The simulation study shows that the designed controller by Iteration PSO performs better than Classical PSO in finding the solution.
Abstract: Design for cost (DFC) is a method that reduces life
cycle cost (LCC) from the angle of designers. Multiple domain
features mapping (MDFM) methodology was given in DFC. Using
MDFM, we can use design features to estimate the LCC. From the
angle of DFC, the design features of family cars were obtained, such
as all dimensions, engine power and emission volume. At the
conceptual design stage, cars- LCC were estimated using back
propagation (BP) artificial neural networks (ANN) method and
case-based reasoning (CBR). Hamming space was used to measure the
similarity among cases in CBR method. Levenberg-Marquardt (LM)
algorithm and genetic algorithm (GA) were used in ANN. The
differences of LCC estimation model between CBR and artificial
neural networks (ANN) were provided. ANN and CBR separately
each method has its shortcomings. By combining ANN and CBR
improved results accuracy was obtained. Firstly, using ANN selected
some design features that affect LCC. Then using LCC estimation
results of ANN could raise the accuracy of LCC estimation in CBR
method. Thirdly, using ANN estimate LCC errors and correct errors in
CBR-s estimation results if the accuracy is not enough accurate.
Finally, economically family cars and sport utility vehicle (SUV) was
given as LCC estimation cases using this hybrid approach combining
ANN and CBR.
Abstract: Fuzzy C-means Clustering algorithm (FCM) is a
method that is frequently used in pattern recognition. It has the
advantage of giving good modeling results in many cases, although,
it is not capable of specifying the number of clusters by itself. In
FCM algorithm most researchers fix weighting exponent (m) to a
conventional value of 2 which might not be the appropriate for all
applications. Consequently, the main objective of this paper is to use
the subtractive clustering algorithm to provide the optimal number of
clusters needed by FCM algorithm by optimizing the parameters of
the subtractive clustering algorithm by an iterative search approach
and then to find an optimal weighting exponent (m) for the FCM
algorithm. In order to get an optimal number of clusters, the iterative
search approach is used to find the optimal single-output Sugenotype
Fuzzy Inference System (FIS) model by optimizing the
parameters of the subtractive clustering algorithm that give minimum
least square error between the actual data and the Sugeno fuzzy
model. Once the number of clusters is optimized, then two
approaches are proposed to optimize the weighting exponent (m) in
the FCM algorithm, namely, the iterative search approach and the
genetic algorithms. The above mentioned approach is tested on the
generated data from the original function and optimal fuzzy models
are obtained with minimum error between the real data and the
obtained fuzzy models.
Abstract: This study aimed at assessing whether and to what extent moral judgment and behaviour were: 1. situation-dependent; 2. selectively dependent on cognitive and affective components; 3. influenced by gender and age; 4. reciprocally congruent. In order to achieve these aims, four different types of moral dilemmas were construed and five types of thinking were presented for each of them – representing five possible ways to evaluate the situation. The judgment criteria included selfishness, altruism, sense of justice, and the conflict between selfishness and the two moral issues. The participants were 250 unpaid volunteers (50% male; 50% female) belonging to two age-groups: young people and adults. The study entailed a 2 (gender) x 2 (age-group) x 5 (type of thinking) x 4 (situation) mixed design: the first two variables were betweensubjects, the others were within-subjects. Results have shown that: 1. moral judgment and behaviour are at least partially affected by the type of situations and by interpersonal variables such as gender and age; 2. moral reasoning depends in a similar manner on cognitive and affective factors; 3. there is not a gender polarity between the ethic of justice and the ethic of cure/ altruism; 4. moral reasoning and behavior are perceived as reciprocally congruent even though their congruence decreases with a more objective assessment. Such results were discussed in the light of contrasting theories on morality.
Abstract: A cart-ball system is a challenging system from the
control engineering point of view. This is due to the nonlinearities,
multivariable, and non-minimum phase behavior present in this
system. This paper is concerned with the problem of modeling and
control of such system. The objective of control strategy is to place
the cart at a desired position while balancing the ball on the top of the
arc-shaped track fixed on the cart. A State-Feedback Controller
(SFC) with a pole-placement method will be designed in order to
control the system. At first, the mathematical model of a cart-ball
system in the state-space form is developed. Then, the linearization of
a model will be established in order to design a SFC. The integral
control strategy will be performed as to control the cart position of a
system. Simulation work is then performed using
MATLAB/SIMULINK software in order to study the performance of
SFC when applied to the system.
Abstract: In this paper, we propose effective system for digital music retrieval. We divided proposed system into Client and Server. Client part consists of pre-processing and Content-based feature extraction stages. In pre-processing stage, we minimized Time code Gap that is occurred among same music contents. As content-based feature, first-order differentiated MFCC were used. These presented approximately envelop of music feature sequences. Server part included Music Server and Music Matching stage. Extracted features from 1,000 digital music files were stored in Music Server. In Music Matching stage, we found retrieval result through similarity measure by DTW. In experiment, we used 450 queries. These were made by mixing different compression standards and sound qualities from 50 digital music files. Retrieval accurate indicated 97% and retrieval time was average 15ms in every single query. Out experiment proved that proposed system is effective in retrieve digital music and robust at various user environments of web.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: Saturated hydraulic conductivity is one of the soil
hydraulic properties which is widely used in environmental studies
especially subsurface ground water. Since, its direct measurement is
time consuming and therefore costly, indirect methods such as
pedotransfer functions have been developed based on multiple linear
regression equations and neural networks model in order to estimate
saturated hydraulic conductivity from readily available soil
properties e.g. sand, silt, and clay contents, bulk density, and organic
matter. The objective of this study was to develop neural networks
(NNs) model to estimate saturated hydraulic conductivity from
available parameters such as sand and clay contents, bulk density,
van Genuchten retention model parameters (i.e. r
θ , α , and n) as well
as effective porosity. We used two methods to calculate effective
porosity: : (1) eff s FC φ =θ -θ , and (2) inf φ =θ -θ eff s , in which s
θ is
saturated water content, FC θ is water content retained at -33 kPa
matric potential, and inf θ is water content at the inflection point.
Total of 311 soil samples from the UNSODA database was divided
into three groups as 187 for the training, 62 for the validation (to
avoid over training), and 62 for the test of NNs model. A commercial
neural network toolbox of MATLAB software with a multi-layer
perceptron model and back propagation algorithm were used for the
training procedure. The statistical parameters such as correlation
coefficient (R2), and mean square error (MSE) were also used to
evaluate the developed NNs model. The best number of neurons in
the middle layer of NNs model for methods (1) and (2) were
calculated 44 and 6, respectively. The R2 and MSE values of the test
phase were determined for method (1), 0.94 and 0.0016, and for
method (2), 0.98 and 0.00065, respectively, which shows that method
(2) estimates saturated hydraulic conductivity better than method (1).
Abstract: The weighting exponent m is called the fuzzifier that
can have influence on the clustering performance of fuzzy c-means
(FCM) and mÎ[1.5,2.5] is suggested by Pal and Bezdek [13]. In this
paper, we will discuss the robust properties of FCM and show that the
parameter m will have influence on the robustness of FCM. According
to our analysis, we find that a large m value will make FCM more
robust to noise and outliers. However, if m is larger than the theoretical
upper bound proposed by Yu et al. [14], the sample mean will become
the unique optimizer. Here, we suggest to implement the FCM
algorithm with mÎ[1.5,4] under the restriction when m is smaller
than the theoretical upper bound.
Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: The myoelectric signal (MES) is one of the Biosignals
utilized in helping humans to control equipments. Recent approaches
in MES classification to control prosthetic devices employing pattern
recognition techniques revealed two problems, first, the classification
performance of the system starts degrading when the number of
motion classes to be classified increases, second, in order to solve the
first problem, additional complicated methods were utilized which
increase the computational cost of a multifunction myoelectric
control system. In an effort to solve these problems and to achieve a
feasible design for real time implementation with high overall
accuracy, this paper presents a new method for feature extraction in
MES recognition systems. The method works by extracting features
using Wavelet Packet Transform (WPT) applied on the MES from
multiple channels, and then employs Fuzzy c-means (FCM)
algorithm to generate a measure that judges on features suitability for
classification. Finally, Principle Component Analysis (PCA) is
utilized to reduce the size of the data before computing the
classification accuracy with a multilayer perceptron neural network.
The proposed system produces powerful classification results (99%
accuracy) by using only a small portion of the original feature set.
Abstract: K-Means (KM) is considered one of the major
algorithms widely used in clustering. However, it still has some
problems, and one of them is in its initialization step where it is
normally done randomly. Another problem for KM is that it
converges to local minima. Genetic algorithms are one of the
evolutionary algorithms inspired from nature and utilized in the field
of clustering. In this paper, we propose two algorithms to solve the
initialization problem, Genetic Algorithm Initializes KM (GAIK) and
KM Initializes Genetic Algorithm (KIGA). To show the effectiveness
and efficiency of our algorithms, a comparative study was done
among GAIK, KIGA, Genetic-based Clustering Algorithm (GCA),
and FCM [19].
Abstract: Bead-on-plate welds were carried out on AISI 316L
(N) austenitic stainless steel (ASS) using flux cored arc welding
(FCAW) process. The bead on plates weld was conducted as per L25
orthogonal array. In this paper, the weld bead geometry such as depth
of penetration (DOP), bead width (BW) and weld reinforcement (R)
of AISI 316L (N) ASS are investigated. Taguchi approach is used as
statistical design of experiment (DOE) technique for optimizing the
selected welding input parameters. Grey relational analysis and
desirability approach are applied to optimize the input parameters
considering multiple output variables simultaneously. Confirmation
experiment has also been conducted to validate the optimized
parameters.
Abstract: The present work deals with optimization of cascade refrigeration system using eco friendly refrigerants pair R507A and R23. R507A is azeotropic mixture composed of HFC refrigerants R125/R143a (50%/50% by wt.). R23 is a single component HFC refrigerant used as replacement to CFC refrigerant R13 in low temperature applications. These refrigerants have zero ozone depletion potential and are non-flammable. Optimization of R507AR23 cascade refrigeration system performance parameters such as minimum work required, refrigeration effect, coefficient of performance and exergetic efficiency was carried out in terms of eight operating parameters- combinations using Genetic Algorithm tool. The eight operating parameters include (1) low side evaporator temperature (2) high side condenser temperature (3) temperature difference in the cascade heat exchanger (4) low side condenser temperature (5) low side degree of subcooling (6) high side degree of subcooling (7) low side degree of superheating (8) high side degree of superheating. Results show that for minimum work system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and low degree of subcooling and superheating in both side. For maximum refrigeration effect system should operate at high temperature in low side evaporator, high temperature in high side condenser, high temperature difference in cascade condenser, low temperature in low side condenser and higher degree of subcooling in LT and HT side. For maximum coefficient of performance and exergetic efficiency, system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and higher degree of subcooling and superheating in low side of the system.