Abstract: The symmetric solution set Σ sym is the set of all solutions to the linear systems Ax = b, where A is symmetric and lies between some given bounds A and A, and b lies between b and b. We present a contractor for Σ sym, which is an iterative method that starts with some initial enclosure of Σ sym (by means of a cartesian product of intervals) and sequentially makes the enclosure tighter. Our contractor is based on polyhedral approximation and solving a series of linear programs. Even though it does not converge to the optimal bounds in general, it may significantly reduce the overestimation. The efficiency is discussed by a number of numerical experiments.
Abstract: RF performance of SOI CMOS device has attracted
significant amount of interest recently. In order to improve RF
parameters, Strained Si/Relaxed Si0.8Ge0.2 investigated as a
replacement for Si technology .Enhancement of carrier mobility
associated with strain engineering makes Strained Si a promising
candidate for improving RF performance of CMOS technology.
From the simulation, the cut-off frequency is estimated to be 224
GHZ, whereas in SOI at similar bias is about 188 GHZ. Therefore,
Strained Si exhibits 19% improvement in cut-off frequency over
similar Si counterpart. In this paper, Ion/Ioff ratio is studied as one of
the key parameters in logic and digital application. Strained Si/SiGe
demonstrates better Ion/Ioff characteristic than SOI, in similar channel
length of 100 nm.Another important key analog figures of merit such
as Early Voltage (VEA) ,transconductance vs drain current (gm /Ids)
are studied. They introduce the efficiency of the devices to convert
dc power into ac frequency.
Abstract: Single-pole switching scheme is widely used in the
Extra High Voltage system. However, the substantial negativesequence
current injected to the turbine-generators imposes the
electromagnetic (E/M) torque of double system- frequency
components during the dead time (between single-pole clearing and
line reclosing). This would induce supersynchronous resonance
(SPSR) torque amplifications on low pressure turbine generator
blades and even lead to fatigue damage. This paper proposes the
design of a mechanical filter (MF) with natural frequency close to
double-system frequency. From the simulation results, it is found that
such a filter not only successfully damps the resonant effect, but also
has the characteristics of feasibility and compact.
Abstract: The modern telecommunication industry demands
higher capacity networks with high data rate. Orthogonal frequency
division multiplexing (OFDM) is a promising technique for high data
rate wireless communications at reasonable complexity in wireless
channels. OFDM has been adopted for many types of wireless
systems like wireless local area networks such as IEEE 802.11a, and
digital audio/video broadcasting (DAB/DVB). The proposed research
focuses on a concatenated coding scheme that improve the
performance of OFDM based wireless communications. It uses a
Redundant Residue Number System (RRNS) code as the outer code
and a convolutional code as the inner code. Here, a direct conversion
of analog signal to residue domain is done to reduce the conversion
complexity using sigma-delta based parallel analog-to-residue
converter. The bit error rate (BER) performances of the proposed
system under different channel conditions are investigated. These
include the effect of additive white Gaussian noise (AWGN),
multipath delay spread, peak power clipping and frame start
synchronization error. The simulation results show that the proposed
RRNS-Convolutional concatenated coding (RCCC) scheme provides
significant improvement in the system performance by exploiting the
inherent properties of RRNS.
Abstract: With the implied volatility as an important factor in
financial decision-making, in particular in option pricing valuation,
and also the given fact that the pricing biases of Leland option pricing
models and the implied volatility structure for the options are related,
this study considers examining the implied adjusted volatility smile
patterns and term structures in the S&P/ASX 200 index options using
the different Leland option pricing models. The examination of the
implied adjusted volatility smiles and term structures in the
Australian index options market covers the global financial crisis in
the mid-2007. The implied adjusted volatility was found to escalate
approximately triple the rate prior the crisis.
Abstract: Selection of maize (Zea mays) hybrids with wide adaptability across diverse farming environments is important, prior to recommending them to achieve a high rate of hybrid adoption. Grain yield of 14 maize hybrids, tested in a randomized completeblock design with four replicates across 22 environments in Iran, was analyzed using site regression (SREG) stability model. The biplot technique facilitates a visual evaluation of superior genotypes, which is useful for cultivar recommendation and mega-environment identification. The objectives of this study were (i) identification of suitable hybrids with both high mean performance and high stability (ii) to determine mega-environments for maize production in Iran. Biplot analysis identifies two mega-environments in this study. The first mega-environments included KRM, KSH, MGN, DZF A, KRJ, DRB, DZF B, SHZ B, and KHM, where G10 hybrid was the best performing hybrid. The second mega-environment included ESF B, ESF A, and SHZ A, where G4 hybrid was the best hybrid. According to the ideal-hybrid biplot, G10 hybrid was better than all other hybrids, followed by the G1 and G3 hybrids. These hybrids were identified as best hybrids that have high grain yield and high yield stability. GGE biplot analysis provided a framework for identifying the target testing locations that discriminates genotypes that are high yielding and stable.
Abstract: Small tanks, the ancient man-made rain water storage
systems, support the pheasant life and agriculture of the dry zone of
Sri Lanka. Many small tanks were abandoned with time due to
various reasons. Such tanks, rehabilitated in the recent past, were
found to be less sustainable and most of these rehabilitation
approaches have failed. The objective of this research is to assess the
impact of the rehabilitation approaches in the management of small
tanks in the Kurunegala District of Sri Lanka with respect to eight
small tanks. A Sustainability index was developed using seven
indicators representing the ability and commitment of the villagers to
maintain these tanks. The sustainability index of the eight tanks
varied between 79.2 and 47.2 out of a total score of 100. The
conclusion is that, the approaches used for tank rehabilitation have a
significant effect on the sustainability of the management of these
small tanks.
Abstract: Crucial information barely visible to the human eye is
often embedded in a series of low resolution images taken of the
same scene. Super resolution reconstruction is the process of
combining several low resolution images into a single higher
resolution image. The ideal algorithm should be fast, and should add
sharpness and details, both at edges and in regions without adding
artifacts. In this paper we propose a super resolution blind
reconstruction technique for linearly degraded images. In our
proposed technique the algorithm is divided into three parts an image
registration, wavelets based fusion and an image restoration. In this
paper three low resolution images are considered which may sub
pixels shifted, rotated, blurred or noisy, the sub pixel shifted images
are registered using affine transformation model; A wavelet based
fusion is performed and the noise is removed using soft thresolding.
Our proposed technique reduces blocking artifacts and also
smoothens the edges and it is also able to restore high frequency
details in an image. Our technique is efficient and computationally
fast having clear perspective of real time implementation.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: In this paper we present a novel approach for human
Body configuration based on the Silhouette. We propose to address
this problem under the Bayesian framework. We use an effective
Model based MCMC (Markov Chain Monte Carlo) method to solve
the configuration problem, in which the best configuration could be
defined as MAP (maximize a posteriori probability) in Bayesian
model. This model based MCMC utilizes the human body model to
drive the MCMC sampling from the solution space. It converses the
original high dimension space into a restricted sub-space constructed
by the human model and uses a hybrid sampling algorithm. We
choose an explicit human model and carefully select the likelihood
functions to represent the best configuration solution. The
experiments show that this method could get an accurate
configuration and timesaving for different human from multi-views.
Abstract: This study was investigated on sampling and
analyzing water quality in water reservoir & water tower installed in
two kind of residential buildings and school facilities. Data of water
quality was collected for correlation analysis with frequency of
sanitization of water reservoir through questioning managers of
building about the inspection charts recorded on equipment for water
reservoir. Statistical software packages (SPSS) were applied to the
data of two groups (cleaning frequency and water quality) for
regression analysis to determine the optimal cleaning frequency of
sanitization. The correlation coefficient (R) in this paper represented
the degree of correlation, with values of R ranging from +1 to -1.After
investigating three categories of drinking water users; this study found
that the frequency of sanitization of water reservoir significantly
influenced the water quality of drinking water. A higher frequency of
sanitization (more than four times per 1 year) implied a higher quality
of drinking water. Results indicated that sanitizing water reservoir &
water tower should at least twice annually for achieving the aim of
safety of drinking water.
Abstract: Ethanol is generally used as a therapeutic reagent against Hepatocellular carcinoma (HCC or hepatoma) worldwide, as it can induce Hepatocellular carcinoma cell apoptosis at low concentration through a multifactorial process regulated by several unknown proteins. This paper provides a simple and available proteomic strategy for exploring differentially expressed proteins in the apoptotic pathway. The appropriate concentrations of ethanol required to induce HepG2 cell apoptosis were first assessed by MTT assay, Gisma and fluorescence staining. Next, the central proteins involved in the apoptosis pathway processs were determined using 2D-PAGE, SDS-PAGE, and bio-software analysis. Finally the downregulation of two proteins, AFP and survivin, were determined by immunocytochemistry and reverse transcriptase PCR (RT-PCR) technology. The simple, useful method demonstrated here provides a new approach to proteomic analysis in key bio-regulating process including proliferation, differentiation, apoptosis, immunity and metastasis.
Abstract: This paper reports work done to improve the modeling of complex processes when only small experimental data sets are available. Neural networks are used to capture the nonlinear underlying phenomena contained in the data set and to partly eliminate the burden of having to specify completely the structure of the model. Two different types of neural networks were used for the application of pulping problem. A three layer feed forward neural networks, using the Preconditioned Conjugate Gradient (PCG) methods were used in this investigation. Preconditioning is a method to improve convergence by lowering the condition number and increasing the eigenvalues clustering. The idea is to solve the modified odified problem M-1 Ax= M-1b where M is a positive-definite preconditioner that is closely related to A. We mainly focused on Preconditioned Conjugate Gradient- based training methods which originated from optimization theory, namely Preconditioned Conjugate Gradient with Fletcher-Reeves Update (PCGF), Preconditioned Conjugate Gradient with Polak-Ribiere Update (PCGP) and Preconditioned Conjugate Gradient with Powell-Beale Restarts (PCGB). The behavior of the PCG methods in the simulations proved to be robust against phenomenon such as oscillations due to large step size.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: This paper presents an advance in monitoring and
process control of surface roughness in CNC machine for the turning
and milling processes. An integration of the in-process monitoring
and process control of the surface roughness is proposed and
developed during the machining process by using the cutting force
ratio. The previously developed surface roughness models for turning
and milling processes of the author are adopted to predict the inprocess
surface roughness, which consist of the cutting speed, the
feed rate, the tool nose radius, the depth of cut, the rake angle, and
the cutting force ratio. The cutting force ratios obtained from the
turning and the milling are utilized to estimate the in-process surface
roughness. The dynamometers are installed on the tool turret of CNC
turning machine and the table of 5-axis machining center to monitor
the cutting forces. The in-process control of the surface roughness
has been developed and proposed to control the predicted surface
roughness. It has been proved by the cutting tests that the proposed
integration system of the in-process monitoring and the process
control can be used to check the surface roughness during the cutting
by utilizing the cutting force ratio.
Abstract: In this paper, a novel approach for the multidisciplinary design optimization (MDO) of complex mechatronic systems. This approach, which is a part of a global project aiming to include the MDO aspect inside an innovative design process. As a first step, the paper considers the MDO as a redesign approach which is limited to the parametric optimization. After defining and introducing the different keywords, the proposed method which is based on the V-Model which is commonly used in mechatronics.
Abstract: PCCI engines can reduce NOx and PM emissions
simultaneously without sacrificing thermal efficiency, but a low
combustion temperature resulting from early fuel injection, and
ignition occurring prior to TDC, can cause higher THC and CO
emissions and fuel consumption. In conclusion, it was found that the
PCCI combustion achieved by the 2-stage injection strategy with
optimized calibration factors (e.g. EGR rate, injection pressure, swirl
ratio, intake pressure, injection timing) can reduce NOx and PM
emissions simultaneously. This research works are expected to
provide valuable information conducive to a development of an
innovative combustion engine that can fulfill upcoming stringent
emission standards.
Abstract: One of the main advantages of the LO paradigm is to
allow the availability of good quality, shareable learning material
through the Web. The effectiveness of the retrieval process requires a
formal description of the resources (metadata) that closely fits the
user-s search criteria; in spite of the huge international efforts in this
field, educational metadata schemata often fail to fulfil this
requirement. This work aims to improve the situation, by the
definition of a metadata model capturing specific didactic features of
shareable learning resources. It classifies LOs into “teacher-oriented"
and “student-oriented" categories, in order to describe the role a LO
is to play when it is integrated into the educational process. This
article describes the model and a first experimental validation process
that has been carried out in a controlled environment.
Abstract: 3-hydroxy-3-methylglutaryl coenzyme A reductase (HMGR) catalyzes the conversion of HMG-CoA to mevalonate using NADPH and the enzyme is involved in rate-controlling step of mevalonate. Inhibition of HMGR is considered as effective way to lower cholesterol levels so it is drug target to treat hypercholesterolemia, major risk factor of cardiovascular disease. To discover novel HMGR inhibitor, we performed structure-based pharmacophore modeling combined with molecular dynamics (MD) simulation. Four HMGR inhibitors were used for MD simulation and representative structure of each simulation were selected by clustering analysis. Four structure-based pharmacophore models were generated using the representative structure. The generated models were validated used in virtual screening to find novel scaffolds for inhibiting HMGR. The screened compounds were filtered by applying drug-like properties and used in molecular docking. Finally, four hit compounds were obtained and these complexes were refined using energy minimization. These compounds might be potential leads to design novel HMGR inhibitor.
Abstract: The problem of robust stability and robust stabilization for a class of discrete-time uncertain systems with time delay is investigated. Based on Tchebychev inequality, by constructing a new augmented Lyapunov function, some improved sufficient conditions ensuring exponential stability and stabilization are established. These conditions are expressed in the forms of linear matrix inequalities (LMIs), whose feasibility can be easily checked by using Matlab LMI Toolbox. Compared with some previous results derived in the literature, the new obtained criteria have less conservatism. Two numerical examples are provided to demonstrate the improvement and effectiveness of the proposed method.