Abstract: In this paper, the application of the Mode Matching
(MM) method in the case of photonic crystal waveguide
discontinuities is presented. The structure under consideration is
divided into a number of cells, which supports a number of guided
and evanescent modes. These modes can be calculated numerically
by an alternative formulation of the plane wave expansion method
for each frequency. A matrix equation is then formed relating the
modal amplitudes at the beginning and at the end of the structure.
The theory is highly efficient and accurate and can be applied to
study the transmission sensitivity of photonic crystal devices due to
fabrication tolerances. The accuracy of the MM method is compared
to the Finite Difference Frequency Domain (FDFD) and the Adjoint
Variable Method (AVM) and good agreement is observed.
Abstract: Tehran, one of the heavily-populated capitals, is
severely suffering from increasing air pollution. To show a
documented trend of such pollutants during last years, plane tree
species (Platanus orientalis) were suited to be studied as indicators,
for the species have been planted throughout the city many years
ago. Two areas (Saadatabad and Narmak districts) allotting different
contents of crowed and highly-traffic routs but the same ecological
characteristics were selected. Twelve sample individuals were cored
twice perpendicularly in each area. Tree-rings of each core were
measured by a binocular microscope and separated annually for the
last 25 years. Two heavy metals including Cd and Pb accompanied
by a mineral element (Ca) were analyzed using Hatch method. Treerings
analysis of the two areas showed different groups in term of
physiologically ability as the growths were plunged during the last
10 years in Saadatabad district and showed a slight decrease in the
same period for another studying area. In direct contrast to
decreasing growth trend in Saadatabad, all three mentioned elements
increased sharply during last 25 years in the same area. When it came
to Narmak district, the trend was completely different with
Saadatabad. There were some fluctuations in absorbing trace
elements like tree-rings widths were, yet calcium showed an upward
trend all the last 25 years. The results of the study proved the
possibility of using tree species of each region to monitor its air
pollution trends of the past, hence to depict a pollution assessment of
a populated city for last years and then to make appropriate decisions
for the future as it is well-known what the trend is. On the other
hand, risen values of calcium (as the stress-indicator element)
accompanied by increased trace elements suggests non-sustainable
state of the trees.
Abstract: Based on the combined shape feature and texture
feature, a fast object detection method with rotation invariant features
is proposed in this paper. A quick template matching scheme based
online learning designed for online applications is also introduced in
this paper. The experimental results have shown that the proposed
approach has the features of lower computation complexity and
higher detection rate, while keeping almost the same performance
compared to the HOG-based method, and can be more suitable for
run time applications.
Abstract: Design of a constant chord propeller is presented in
this paper in order to reduce propeller-s design procedure-s costs. The
design process was based on Lock and Goldstein-s techniques of
propeller design and analysis. In order to calculate optimum chord of
propeller, chord of a referential element is generalized as whole
blades chord. The design outcome which named CS-X-1 is modeled
& analyzed by CFD methods using K-ε: R.N.G turbulence model.
Convergence of results of two codes proved that outcome results of
design process are reliable. Design result is a two-blade propeller
with a total diameter of 1.1 meter, radial velocity of 3000 R.P.M,
efficiency above .75 and power coefficient near 1.05.
Abstract: The main objective of this work is to compare the
quality of service of the bus companies operating in the city of Rio
Branco, located in the state of Acre with the quality of service of the
bus companies operating in the city of Campos, situated in the state
of Rio de Janeiro, both cities in Brazil. This comparison, based on the
opinion of the bus users, will determine their degree of satisfaction
with the service available in both cities. The outcome of this
evaluation shows the users unhappy with the quality of the service
provided by the bus companies operating in both cities and the need
to identify alternative solutions that may minimize the consequences
caused by the main problems detected in this work. With these
alternatives available, the bus companies will be able to better
understand the needs of their customers in terms of manpower,
service cost, time schedule, etc.
Abstract: Computational simulation of steam flow and heat transfer in power plant condensers on the basis of the threedimensional mathematical model for the flow through porous media is presented. In order to solve the mathematical model of steam flow and heat transfer in power plant condensers, the Streamline Upwind Petrov-Galerkin finite element method is applied. By comparison of the results of simulation with experimental results about an experimental condenser, it is confirmed that SUPG finite element method can be successfully applied for solving the three-dimensional mathematical model of steam flow and heat transfer in power plant condensers.
Abstract: Iris pattern is an important biological feature of human body; it becomes very hot topic in both research and practical applications. In this paper, an algorithm is proposed for iris recognition and a simple, efficient and fast method is introduced to extract a set of discriminatory features using first order gradient operator applied on grayscale images. The gradient based features are robust, up to certain extents, against the variations may occur in contrast or brightness of iris image samples; the variations are mostly occur due lightening differences and camera changes. At first, the iris region is located, after that it is remapped to a rectangular area of size 360x60 pixels. Also, a new method is proposed for detecting eyelash and eyelid points; it depends on making image statistical analysis, to mark the eyelash and eyelid as a noise points. In order to cover the features localization (variation), the rectangular iris image is partitioned into N overlapped sub-images (blocks); then from each block a set of different average directional gradient densities values is calculated to be used as texture features vector. The applied gradient operators are taken along the horizontal, vertical and diagonal directions. The low order norms of gradient components were used to establish the feature vector. Euclidean distance based classifier was used as a matching metric for determining the degree of similarity between the features vector extracted from the tested iris image and template features vectors stored in the database. Experimental tests were performed using 2639 iris images from CASIA V4-Interival database, the attained recognition accuracy has reached up to 99.92%.
Abstract: Based on the one-bit-matching principle and by turning the de-mixing matrix into an orthogonal matrix via certain normalization, Ma et al proposed a one-bit-matching learning algorithm on the Stiefel manifold for independent component analysis [8]. But this algorithm is not adaptive. In this paper, an algorithm which can extract kurtosis and its sign of each independent source component directly from observation data is firstly introduced.With the algorithm , the one-bit-matching learning algorithm is revised, so that it can make the blind separation on the Stiefel manifold implemented completely in the adaptive mode in the framework of natural gradient.
Abstract: Recently, genetic algorithms (GA) and particle swarm optimization (PSO) technique have attracted considerable attention among various modern heuristic optimization techniques. Since the two approaches are supposed to find a solution to a given objective function but employ different strategies and computational effort, it is appropriate to compare their performance. This paper presents the application and performance comparison of PSO and GA optimization techniques, for Thyristor Controlled Series Compensator (TCSC)-based controller design. The design objective is to enhance the power system stability. The design problem of the FACTS-based controller is formulated as an optimization problem and both the PSO and GA optimization techniques are employed to search for optimal controller parameters. The performance of both optimization techniques in terms of computational time and convergence rate is compared. Further, the optimized controllers are tested on a weakly connected power system subjected to different disturbances, and their performance is compared with the conventional power system stabilizer (CPSS). The eigenvalue analysis and non-linear simulation results are presented and compared to show the effectiveness of both the techniques in designing a TCSC-based controller, to enhance power system stability.
Abstract: Reduced switching loss favours Pulse Skipping
Modulation mode of switching dc-to-dc converters at light loads.
Under certain conditions the converter operates in discontinuous
conduction mode (DCM). Inductor current starts from zero in each
switching cycle as the switching frequency is constant and not
adequately high. A DC-to-DC buck converter is modelled and
simulated in this paper under DCM. Effect of ESR of the filter
capacitor in input current frequency components is studied. The
converter is studied for its operation under input voltage and load
variation. The operating frequency is selected to be close to and
above audio range.
Abstract: This article proposes a current-mode square-rooting
circuit using current follower transconductance amplifier (CTFA).
The amplitude of the output current can be electronically controlled
via input bias current with wide input dynamic range. The proposed
circuit consists of only single CFTA. Without any matching
conditions and external passive elements, the circuit is then
appropriate for an IC architecture. The magnitude of the output signal
is temperature-insensitive. The PSpice simulation results are
depicted, and the given results agree well with the theoretical
anticipation. The power consumption is approximately 1.96mW at
±1.5V supply voltages.
Abstract: Extensive wind tunnel tests have been conducted to
investigate the unsteady flow field over and behind a 2D model of a
660 kW wind turbine blade section in pitching motion. The surface
pressure and wake dynamic pressure variation at a distance of 1.5
chord length from trailing edge were measured by pressure
transducers during several oscillating cycles at 3 reduced frequencies
and oscillating amplitudes. Moreover, form drag and linear
momentum deficit are extracted and compared at various conditions.
The results show that the wake velocity field and surface pressure of
the model have similar behavior before and after the airfoil beyond
the static stall angle of attack. In addition, the effects of reduced
frequency and oscillation amplitudes are discussed.
Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: Pretreatment is an essential step in the conversion of
lignocellulosic biomass to fermentable sugar that used for biobutanol
production. Among pretreatment processes, microwave is considered
to improve pretreatment efficiency due to its high heating efficiency,
easy operation, and easily to combine with chemical reaction. The
main objectives of this work are to investigate the feasibility of
microwave pretreatment to enhance enzymatic hydrolysis of
corncobs and to determine the optimal conditions using response
surface methodology. Corncobs were pretreated via two-stage
pretreatment in dilute sodium hydroxide (2 %) followed by dilute
sulfuric acid 1 %. Pretreated corncobs were subjected to enzymatic
hydrolysis to produce reducing sugar. Statistical experimental design
was used to optimize pretreatment parameters including temperature,
residence time and solid-to-liquid ratio to achieve the highest amount
of glucose. The results revealed that solid-to-liquid ratio and
temperature had a significant effect on the amount of glucose.
Abstract: This study evaluated the microbiological quality
and the sensory characteristics of carp fillets processed by the
sousvide method when stored at 2 and 10 °C. Four different
combinations of sauced–storage were studied then stored at 2 or 10
°C was evaluate periodically sensory, microbiological and
chemical quality. Batches stored at 2 °C had lower growth rates of
mesophiles and psychrotrophs. Moreover, these counts decreased
by increasing the heating temperature and time. Staphylococcus
aureus, Bacillus cereus, Clostridium perfringens and Listeria
monocytogenes were not found in any of the samples. The heat
treatment of 90 °C for 15 min and sauced was the most effective to
ensure the safety and extend the shelf-life of sousvide carp
preserving its sensory characteristics. This study establishes the
microbiological quality of sous vide carp and emphasizes the
relevance of the raw materials, heat treatment and storage
temperature to ensure the safety of the product.
Abstract: Lateral expansion is a factor defining the level of
confinement in reinforced concrete columns. Therefore, predicting
the lateral strain relationship with axial strain becomes an important
issue. Measuring lateral strains in experiments is difficult and only
few report experimental lateral strains. Among the existing analytical
formulations, two recent models are compared with available test
results in this paper with shortcomings highlighted. A new analytical
model is proposed here for lateral strain axial strain relationship and
is based on the supposition that the concrete behaves linear elastic in
the early stages of loading and then nonlinear hardening up to the
peak stress and then volumetric expansion. The proposal for the
lateral strain axial strain relationship after the peak stress is mainly
based on the hypothesis that the plastic lateral strain varies linearly
with the plastic axial strain and it is shown that this is related to the
lateral confinement level.
Abstract: This paper presents a perturbation based search method
to solve the unconstrained binary quadratic programming problem.
The proposed algorithm was tested with some of the standard test
problems and the results are reported for 10 instances of 50, 100, 250,
& 500 variable problems. A comparison of the performance of the
proposed algorithm with other heuristics and optimization software is
made. Based on the results, it was found that the proposed algorithm
is computationally inexpensive and the solutions obtained match the
best known solutions for smaller sized problems. For larger instances,
the algorithm is capable of finding a solution within 0.11% of the
best known solution. Apart from being used as a stand-alone method,
this algorithm could also be incorporated with other heuristics to find
better solutions.
Abstract: The chatter is one of the major limitations of the productivity in the ball end milling process. It affects the surface roughness, the dimensional accuracy and the tool life. The aim of this research is to propose the new system to detect the chatter during the ball end milling process by using the wavelet transform. The proposed method is implemented on the 5-axis CNC machining center and the new three parameters are introduced from three dynamic cutting forces, which are calculated by taking the ratio of the average variances of dynamic cutting forces to the absolute variances of themselves. It had been proved that the chatter can be easier to detect during the in-process cutting by using the new parameters which are proposed in this research. The experimentally obtained results showed that the wavelet transform can provide the reliable results to detect the chatter under various cutting conditions.
Abstract: In this paper, enhanced ground proximity warning simulation and validation system is designed and implemented. First, based on square grid and sub-grid structure, the global digital terrain database is designed and constructed. Terrain data searching is implemented through querying the latitude and longitude bands and separated zones of global terrain database with the current aircraft position. A combination of dynamic scheduling and hierarchical scheduling is adopted to schedule the terrain data, and the terrain data can be read and delete dynamically in the memory. Secondly, according to the scope, distance, approach speed information etc. to the dangerous terrain in front, and using security profiles calculating method, collision threat detection is executed in real-time, and provides caution and warning alarm. According to this scheme, the implementation of the enhanced ground proximity warning simulation system is realized. Simulations are carried out to verify a good real-time in terrain display and alarm trigger, and the results show simulation system is realized correctly, reasonably and stable.
Abstract: In this article, we synthesize a novel chitosan -based
superabsorbent hydrogel via graft copolymerization of mixtures
acrylic acid (AA) and N-vinyl pyrollidon onto chitosan backbones.
The polymerization reaction was carried out in an aqueous medium
and in the presence of ammonium persulfate (APS) as an initiator and
N,N'-methylene bisacrylamide (MBA) as a crosslinker.The hydrogel
structures were confirmed by FTIR spectroscopy. The swelling
behavior of these absorbent polymers was also investigated in
various salt solutions. Results indicated that the swelling capacity
decreased with an increase in the ionic strength of the swelling
medium. Furthermore, the swelling of superabsorbing hydrogels was
examined in solutions with pH values ranging between 1.0 and 13.0.
It showed a reversible pH-responsive behavior at pHs 2.0 and 8.0.
This on-off switching behavior makes the synthesized hydrogels as
an excellent candidate for controlled delivery of bioactive agents.