Abstract: Various solar energy technologies exist and they have
different application techniques in the generation of electrical power.
The widespread use of photovoltaic (PV) modules in such
technologies has been limited by relatively high costs and low
efficiencies. The efficiency of PV panels decreases as the operating
temperatures increase. This is due to the affect of solar intensity and
ambient temperature. In this work, Computational Fluid Dynamics
(CFD) was used to model the heat transfer from a standard PV panel
and thus determine the rate of dissipation of heat. To accurately
model the specific climatic conditions of the United Arab Emirates
(UAE), a case study of a new build green building in Dubai was
used. A finned heat pipe arrangement is proposed and analyzed to
determine the improved heat dissipation and thus improved
performance efficiency of the PV panel. A prototype of the
arrangement is built for experimental testing to validate the CFD
modeling and proof of concept.
Abstract: Arenga pinnata is an abundantly natural fiber that can be used for sound proof material. However, the scientific data of acoustics properties of Arenga pinnata was not available yet. In this study the sound absorption of pure arenga pinnata was measured. The thickness of Arenga pinnata was varied in 10 mm, 20 mm, 30mm, and 40mm. This work was carried out to investigate the potential of using Arenga pinnata fiber as raw material for sound absorbing material. Impedance Tube Method was used to measure sound absorption coefficient (α). The Measurements was done in accordance with ASTM E1050-98, that is the standard test method for impedance and absorption of acoustical materials using a tube, two microphones and a digital frequency analysis system . The results showed that sound absorption coefficients of Arenga pinnata were good from 2000 Hz to 5000 Hz within the range of 0.75 – 0.90. The optimum sound absorption coefficient was obtained from the thickness of 40 mm. These results indicated that Arenga pinnata fiber is promising to be used as raw material of sound absorbing material with low cost, light, and biodegradable.
Abstract: Tandem mass spectrometry (MS/MS) is the engine
driving high-throughput protein identification. Protein mixtures possibly
representing thousands of proteins from multiple species are
treated with proteolytic enzymes, cutting the proteins into smaller
peptides that are then analyzed generating MS/MS spectra. The
task of determining the identity of the peptide from its spectrum
is currently the weak point in the process. Current approaches to de
novo sequencing are able to compute candidate peptides efficiently.
The problem lies in the limitations of current scoring functions. In this
paper we introduce the concept of proteome signature. By examining
proteins and compiling proteome signatures (amino acid usage) it is
possible to characterize likely combinations of amino acids and better
distinguish between candidate peptides. Our results strongly support
the hypothesis that a scoring function that considers amino acid usage
patterns is better able to distinguish between candidate peptides. This
in turn leads to higher accuracy in peptide prediction.
Abstract: This study aims to investigate how much both son and
daughter trust their father and what are the underlying reasons they
trust their father. The results revealed five main reasons why
Malaysian adolescents trust their father. Those reasons are related to
the role of father, father-child relationship, father-s characteristics,
father-s nurturing nature and father-s attitude and behavior. A total of
1022 students (males = 241, females = 781) from one of public
university in Sabah, Malaysia participated in the study. The
participants completed open-ended questionnaires developed by Kim
(2008), asking how much the adolescents trust their father, and the
reasons why they trust their father. The data was analysed by using
the indigenous psychology method proposed by [1] Findings of this
study revealed the pattern of trust towards father for both Malaysian
male and female adolescents. The results contributed new
information about Malaysian adolescents- trust towards their father
form the indigenous context. The implications of finding will be
discussed.
Abstract: This paper presents a review of an 8-year study on radiation effects in commercial memory devices operating within the main on-board computer system OBC386 of the Algerian microsatellite Alsat-1. A statistical analysis of single-event upset (SEU) and multiple-bit upset (MBU) activity in these commercial memories shows that the typical SEU rate at alsat-1's orbit is 4.04 × 10-7 SEU/bit/day, where 98.6% of these SEUs cause single-bit errors, 1.22% cause double-byte errors, and the remaining SEUs result in multiple-bit and severe errors.
Abstract: Biogas, a clean renewable energy, is attracting a growing
concern of researchers and professionals in many fields. Based
on the natural and climatic conditions in semi-arid regions of northwestern
China, the present study introduces a specifically-designed
family-size biogas plant (with a digester of 10m3) with manure
and urine of animals and humanity as raw materials. The biogas
plant is applicable to areas with altitudes of more than 2000 meters
in northwestern China. In addition to the installation cost, a little
operational expenditure, structure, characteristics, benefits of this
small-scale biogas plant, this article introduces a wide range of
specific popularization methods such as training, financial support,
guided tour to the biogas plant, community-based group study and
delivery of operational manuals. The feasibility of the biogas plant is
explored on the basis of the availability of the raw materials. Simple
operations contained in the current work increase the possibility of
the wide use of this small-scale biogas plant in similar regions of the
world.
Abstract: This research aimed to develop plasma system used in air conditioners. This developed plasma system could be installed in the air conditioners - all split type. The quality of air could be improved to be equal to present plasma system. Development processes were as follows: 1) to study the plasma system used in the air conditioners, 2) to design a plasma generator, 3) to develop the plasma generator, and 4) to test its performance in many types of the air conditioners. This plasma system was developed by AC high voltage – 14 kv with a frequency of 50 kHz. Carbon was a conductor to generate arc in air purifier system. The research was tested by installing the plasma generator in the air conditioners - wall type. Whereas, there were 3 types of installations: air flow out, air flow in, and room center. The result of the plasma generator installed in the air conditioners, split type, revealed that the air flow out installation provided the highest average of o-zone at 223 mg/h. This type of installation provided the highest efficiency of air quality improvement. Moreover, the air flow in installation and the room center installation provided the average of the o-zone at 163 mg/h and 64 mg/h, respectively.
Abstract: Von Willebrand-s disease is the most common
inherited bleeding disorder in humans, it
caused by qualitative abnormalities of the von Willebrand factor
(vWF). Our objective is to determine the prevalence of this disease at
part of the Algerian population in the East and the South by a
biological diagnosis based on specific biological tests (automated
platelet count, the bleeding time (TS), the time of cephalin + activator
(TCA), measure of the prothrombin rate (TP), vWF rate and factor
VIII rate, Molecular electrophoresis of vWF multimers in agarose gel
in the presence of SDS). Four patients of type III or severe
Willebrand-s disease were found on 200 suspect cases. All cases are
showed a deficit in vWF rate (< 5%), and factor VIII (P
Abstract: K-Modes is an extension of K-Means clustering algorithm, developed to cluster the categorical data, where the mean is replaced by the mode. The similarity measure proposed by Huang is the simple matching or mismatching measure. Weight of attribute values contribute much in clustering; thus in this paper we propose a new weighted dissimilarity measure for K-Modes, based on the ratio of frequency of attribute values in the cluster and in the data set. The new weighted measure is experimented with the data sets obtained from the UCI data repository. The results are compared with K-Modes and K-representative, which show that the new measure generates clusters with high purity.
Abstract: Nowadays for algae cell ultrasonication the
longitudinal ultrasonic piezosystems are used. In this paper a
possibility of creating unique ultrasonic piezoelectric system, which
would allow reducing energy losses and concentrating this energy to
a small closed volume are proposed. The current vibrating systems
whose ultrasonic energy is concentrated inside of hollow cylinder in
which water-algae mixture is flowing. Two, three or multiply
ultrasonic composite systems to concentrate total energy into a
hollow cylinder to creating strong algae cell ultrasonication are used.
The experiments and numerical FEM analysis results using diskshaped
transducer and the first biological test results on algae cell
disruption by ultrasonication are presented as well.
Abstract: Each new semiconductor technology node
brings smaller transistors and wires. Although this makes
transistors faster, wires get slower. In nano-scale regime, the
standard copper (Cu) interconnect will become a major hurdle
for FPGA interconnect due to their high resistivity and
electromigration. This paper presents the comprehensive
evaluation of mixed CNT bundle interconnects and
investigates their prospects as energy efficient and high speed
interconnect for future FPGA routing architecture. All
HSPICE simulations are carried out at operating frequency of
1GHz and it is found that mixed CNT bundle implemented in
FPGAs as interconnect can potentially provide a substantial
delay and energy reduction over traditional interconnects at
32nm process technology.
Abstract: With continuous rise of oil price, how to develop alternative energy source has become a hot topic around the world. This study discussed the dynamic characteristics of an island power system operating under random wind speed lower than nominal wind
speeds of wind turbines. The system primarily consists of three diesel engine power generation systems, three constant-speed variable-pitch wind turbines, a small hydraulic induction generation system, and lumped static loads. Detailed models based on Matlab/Simulink were developed to cater for the dynamic behavior of the system. The results suggested this island power system can operate stably in this operational mode. This study can serve as an important reference for planning, operation, and further expansion of island power systems.
Abstract: The focal spot of a high intensity focused ultrasound
transducer is small. To heat a large target volume, multiple treatment spots are required. If the power of each treatment spot is fixed, it could
results in insufficient heating of initial spots and over-heating of later ones, which is caused by the thermal diffusion. Hence, to produce a
uniform heated volume, the delivered energy of each treatment spot
should be properly adjusted. In this study, we proposed an iterative, extrapolation technique to adjust the required ultrasound energy of
each treatment spot. Three different scanning pathways were used to evaluate the performance of this technique. Results indicate that by using the proposed technique, uniform heating volume could be obtained.
Abstract: The paper describes the carbonate microfacies identified in the Sinjar Formation (Late Paleocene–Early Eocene) cropping out in Qara Dagh Mountain, near Sulekan Village approximately 20km south–west of Sulaimani (Iraq). One section (62m thick) has been measured in the field and closely sampled to undertake detailed microfaciesal and micropalaeontological studies to determine the formation-s age and environment of deposition. A samples were collected illustrating all the lithological changes along the section. The limestone in the studied area is hard and extremely rich in large foraminifers (soritids, rotaliids, nummulites, miliolids) and green algae (dasycladales). The investigation of the thin sections allowed us to identify the carbonate microfacies (18 types and subtypes) and the micropaleontological association (foraminifers and green algae), to determine the age of formation and to reconstruct the paleoenvironment of deposition (fore-reef, reef, back-reef). Based on the field observations and the studied thin sections, we determined three Units of a carbonate platform (I, II and III) from the base to the top of the section: Unit I with coralgal associations, Unit II is dominated by larger foraminifers and haracterized by the absence of coralgal associations, while Unit III is dominated by small foraminifers (mostly miliolids), peloids and green algae. It is partially dolomitized.
Abstract: Existing proceeding-models for the development of mechatronic systems provide a largely parallel action in the detailed development. This parallel approach is to take place also largely independent of one another in the various disciplines involved. An approach for a new proceeding-model provides a further development of existing models to use for the development of Adaptronic Systems. This approach is based on an intermediate integration and an abstract modeling of the adaptronic system. Based on this system-model a simulation of the global system behavior, due to external and internal factors or Forces is developed. For the intermediate integration a special data management system is used. According to the presented approach this data management system has a number of functions that are not part of the "normal" PDM functionality. Therefore a concept for a new data management system for the development of Adaptive system is presented in this paper. This concept divides the functions into six layers. In the first layer a system model is created, which divides the adaptronic system based on its components and the various technical disciplines. Moreover, the parameters and properties of the system are modeled and linked together with the requirements and the system model. The modeled parameters and properties result in a network which is analyzed in the second layer. From this analysis necessary adjustments to individual components for specific manipulation of the system behavior can be determined. The third layer contains an automatic abstract simulation of the system behavior. This simulation is a precursor for network analysis and serves as a filter. By the network analysis and simulation changes to system components are examined and necessary adjustments to other components are calculated. The other layers of the concept treat the automatic calculation of system reliability, the "normal" PDM-functionality and the integration of discipline-specific data into the system model. A prototypical implementation of an appropriate data management with the addition of an automatic system development is being implemented using the data management system ENOVIA SmarTeam V5 and the simulation system MATLAB.
Abstract: In this paper, design, fabrication and coupled
multifield analysis of hollow out-of-plane silicon microneedle array
with piezoelectrically actuated microfluidic device for transdermal
drug delivery (TDD) applications is presented. The fabrication
process of silicon microneedle array is first done by series of
combined isotropic and anisotropic etching processes using
inductively coupled plasma (ICP) etching technology. Then coupled
multifield analysis of MEMS based piezoelectrically actuated device
with integrated 2×2 silicon microneedle array is presented. To predict
the stress distribution and model fluid flow in coupled field analysis,
finite element (FE) and computational fluid dynamic (CFD) analysis
using ANSYS rather than analytical systems has been performed.
Static analysis and transient CFD analysis were performed to predict
the fluid flow through the microneedle array. The inlet pressure from
10 kPa to 150 kPa was considered for static CFD analysis. In the
lumen region fluid flow rate 3.2946 μL/min is obtained at 150 V for
2×2 microneedle array. In the present study the authors have
performed simulation of structural, piezoelectric and CFD analysis
on three dimensional model of the piezoelectrically actuated
mcirofluidic device integrated with 2×2 microneedle array.
Abstract: Our objective in this paper is to propose an approach
capable of clustering web messages. The clustering is carried out by
assigning, with a certain probability, texts written by the same web
user to the same cluster based on Stylometric features and using
fuzzy clustering algorithms. Focus in the present work is on
comparing the most popular algorithms in fuzzy clustering theory
namely, Fuzzy C-means, Possibilistic C-means and Fuzzy
Possibilistic C-Means.
Abstract: Meshing is the process of discretizing problem
domain into many sub domains before the numerical calculation can
be performed. One of the most popular meshes among many types of meshes is tetrahedral mesh, due to their flexibility to fit into almost
any domain shape. In both 2D and 3D domains, triangular and tetrahedral meshes can be generated by using Delaunay triangulation.
The quality of mesh is an important factor in performing any Computational Fluid Dynamics (CFD) simulations as the results is
highly affected by the mesh quality. Many efforts had been done in
order to improve the quality of the mesh. The paper describes a mesh
generation routine which has been developed capable of generating
high quality tetrahedral cells in arbitrary complex geometry. A few
test cases in CFD problems are used for testing the mesh generator.
The result of the mesh is compared with the one generated by a
commercial software. The results show that no sliver exists for the
meshes generated, and the overall quality is acceptable since the percentage of the bad tetrahedral is relatively small. The boundary
recovery was also successfully done where all the missing faces are
rebuilt.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: A numerical investigation of the effects of nanosecond
barrier discharge on the stability of a two-dimensional free shear layer
is performed. The computations are carried out using a compressible
Navier-Stokes algorithm coupled with a thermodynamic model of the
discharge. The results show that significant increases in the shear
layer-s momentum thickness and Reynolds stresses occur due to
actuation. Dependence on both frequency and amplitude of actuation
are considered, and a comparison is made of the computed growth
rates with those predicted by linear stability theory. Amplitude and
frequency ranges for the efficient promotion of shear-layer instabilities
are identified.