Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: Categorical data based on description of the
agricultural landscape imposed some mathematical and analytical
limitations. This problem however can be overcome by data
transformation through coding scheme and the use of non-parametric
multivariate approach. The present study describes data
transformation from qualitative to numerical descriptors. In a
collection of 103 random soil samples over a 60 hectare field,
categorical data were obtained from the following variables: levels of
nitrogen, phosphorus, potassium, pH, hue, chroma, value and data on
topography, vegetation type, and the presence of rocks. Categorical
data were coded, and Spearman-s rho correlation was then calculated
using PAST software ver. 1.78 in which Principal Component
Analysis was based. Results revealed successful data transformation,
generating 1030 quantitative descriptors. Visualization based on the
new set of descriptors showed clear differences among sites, and
amount of variation was successfully measured. Possible applications
of data transformation are discussed.
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Transient Stability is an important issue in power systems planning, operation and extension. The objective of transient stability analysis problem is not satisfied with mere transient instability detection or evaluation and it is most important to complement it by defining fast and efficient control measures in order to ensure system security. This paper presents a new Fuzzy Support Vector Machines (FSVM) to investigate the stability status of power systems and a modified generation rescheduling scheme to bring back the identified unstable cases to a more economical and stable operating point. FSVM improves the traditional SVM (Support Vector Machines) by adding fuzzy membership to each training sample to indicate the degree of membership of this sample to different classes. The preventive control based on economic generator rescheduling avoids the instability of the power systems with minimum change in operating cost under disturbed conditions. Numerical results on the New England 39 bus test system show the effectiveness of the proposed method.
Abstract: In intensity modulated radiation therapy (IMRT)
treatment planning, beam angles are usually preselected on the basis of
experience and intuition. Therefore, getting an appropriate beam
configuration needs a very long time. Based on the present situation,
the paper puts forward beam orientation optimization using ant colony
optimization (ACO). We use ant colony optimization to select the
beam configurations, after getting the beam configuration using
Conjugate Gradient (CG) algorithm to optimize the intensity profiles.
Combining with the information of the effect of pencil beam, we can
get the global optimal solution accelerating. In order to verify the
feasibility of the presented method, a simulated and clinical case was
tested, compared with dose-volume histogram and isodose line
between target area and organ at risk. The results showed that the
effect was improved after optimizing beam configurations. The
optimization approach could make treatment planning meet clinical
requirements more efficiently, so it had extensive application
perspective.
Abstract: International literature emphasizes on the concern regarding the phenomenon of aggression in hospital. This paper focuses on the reality of aggressive interactions reigning within an emergency triage involving three chaps of protagonists: the professionals, the patients and their carers. The data collection was made from a grid of observation, in which the various variables exposed in the literature were integrated. They observations took place around the clock, for three weeks, at the rate of one week a month. In this research 331 aggressive interactions have been listed and analyzed by means of the software SPSS. This research is one of the very few continuous observation surveys in the literature. It shows the various human factors at play in the emergence of aggressive interaction. The data may be used both for taking steps in primary prevention, thanks to the analysis of interaction modes, and in secondary prevention by integrating the useful results in situational prevention.
Abstract: The choice of finite element to use in order to predict
nonlinear static or dynamic response of complex structures becomes
an important factor. Then, the main goal of this research work is to
focus a study on the effect of the in-plane rotational degrees of
freedom in linear and geometrically non linear static and dynamic
analysis of thin shell structures by flat shell finite elements. In this
purpose: First, simple triangular and quadrilateral flat shell finite
elements are implemented in an incremental formulation based on the
updated lagrangian corotational description for geometrically
nonlinear analysis. The triangular element is a combination of DKT
and CST elements, while the quadrilateral is a combination of DKQ
and the bilinear quadrilateral membrane element. In both elements,
the sixth degree of freedom is handled via introducing fictitious
stiffness. Secondly, in the same code, the sixth degrees of freedom in
these elements is handled differently where the in-plane rotational
d.o.f is considered as an effective d.o.f in the in-plane filed
interpolation. Our goal is to compare resulting shell elements. Third,
the analysis is enlarged to dynamic linear analysis by direct
integration using Newmark-s implicit method. Finally, the linear
dynamic analysis is extended to geometrically nonlinear dynamic
analysis where Newmark-s method is used to integrate equations of
motion and the Newton-Raphson method is employed for iterating
within each time step increment until equilibrium is achieved. The
obtained results demonstrate the effectiveness and robustness of the
interpolation of the in-plane rotational d.o.f. and present deficiencies
of using fictitious stiffness in dynamic linear and nonlinear analysis.
Abstract: This paper proposes a method for speckle reduction in
medical ultrasound imaging while preserving the edges with the
added advantages of adaptive noise filtering and speed. A nonlinear
image diffusion method that incorporates local image parameter,
namely, scatterer density in addition to gradient, to weight the
nonlinear diffusion process, is proposed. The method was tested for
the isotropic case with a contrast detail phantom and varieties of
clinical ultrasound images, and then compared to linear and some
other diffusion enhancement methods. Different diffusion parameters
were tested and tuned to best reduce speckle noise and preserve
edges. The method showed superior performance measured both
quantitatively and qualitatively when incorporating scatterer density
into the diffusivity function. The proposed filter can be used as a
preprocessing step for ultrasound image enhancement before
applying automatic segmentation, automatic volumetric calculations,
or 3D ultrasound volume rendering.
Abstract: A prototype model of an emulsion separator was
designed and manufactured. Generally, it is a cylinder filled with
different fractal modules. The emulsion was fed into the reactor by a
peristaltic pump through an inlet placed at the boundary between the
two phases. For hydrodynamic design and sizing of the reactor the
assumptions of the theory of filtration were used and methods to
describe the separation process were developed. Based on this
methodology and using numerical methods and software of Autodesk
the process is simulated in different operating modes. The basic
hydrodynamic characteristics - speed and performance for different
types of fractal systems and decisions to optimize the design of the
reactor were also defined.
Abstract: Robots- visual perception is a field that is gaining
increasing attention from researchers. This is partly due to emerging
trends in the commercial availability of 3D scanning systems or
devices that produce a high information accuracy level for a variety of
applications. In the history of mining, the mortality rate of mine workers
has been alarming and robots exhibit a great deal of potentials to
tackle safety issues in mines. However, an effective vision system
is crucial to safe autonomous navigation in underground terrains.
This work investigates robots- perception in underground terrains
(mines and tunnels) using statistical region merging (SRM) model.
SRM reconstructs the main structural components of an imagery
by a simple but effective statistical analysis. An investigation is
conducted on different regions of the mine, such as the shaft, stope
and gallery, using publicly available mine frames, with a stream of
locally captured mine images. An investigation is also conducted on a
stream of underground tunnel image frames, using the XBOX Kinect
3D sensors. The Kinect sensors produce streams of red, green and
blue (RGB) and depth images of 640 x 480 resolution at 30 frames per
second. Integrating the depth information to drivability gives a strong
cue to the analysis, which detects 3D results augmenting drivable and
non-drivable regions in 2D. The results of the 2D and 3D experiment
with different terrains, mines and tunnels, together with the qualitative
and quantitative evaluation, reveal that a good drivable region can be
detected in dynamic underground terrains.
Abstract: The aim of this article is to assess the existing
business models used by the banks operating in the CEE countries in
the time period from 2006 till 2011.
In order to obtain research results, the authors performed
qualitative analysis of the scientific literature on bank business
models, which have been grouped into clusters that consist of such
components as: 1) capital and reserves; 2) assets; 3) deposits, and 4)
loans.
In their turn, bank business models have been developed based on
the types of core activities of the banks, and have been divided into
four groups: Wholesale, Investment, Retail and Universal Banks.
Descriptive statistics have been used to analyse the models,
determining mean, minimal and maximal values of constituent
cluster components, as well as standard deviation. The analysis of
the data is based on such bank variable indices as Return on Assets
(ROA) and Return on Equity (ROE).
Abstract: Uranium mining and processing in Brazil occur in a
northeastern area near to Caetité-BA. Several Non-Governmental
Organizations claim that uranium mining in this region is a pollutant
causing health risks to the local population,but those in charge of the
complex extraction and production of“yellow cake" for generating
fuel to the nuclear power plants reject these allegations. This study
aimed at identifying potential problems caused by mining to the
population of Caetité. In this, work,the concentrations of 238U, 232Th
and 40K radioisotopes in the teeth of the Caetité population were
determined by ICP-MS. Teeth are used as bioindicators of
incorporated radionuclides. Cumulative radiation doses in the
skeleton were also determined. The concentration values were below
0.008 ppm, and annual effective dose due to radioisotopes are below
to the reference values. Therefore, it is not possible to state that the
mining process in Caetité increases pollution or radiation exposure in
a meaningful way.
Abstract: Majority of pepper farmers in Malaysia are using the
open-sun method for drying the pepper berries. This method is time
consuming and exposed the berries to rain and contamination. A
maintenance-friendly and properly enclosed dryer is therefore
desired. A dryer design with a solar collector and a chimney was
studied and adapted to suit the needs of small-scale pepper farmers in
Malaysia. The dryer will provide an environment with an optimum
operating temperature meant for drying pepper berries. The dryer
model was evaluated by using commercially available computational
fluid dynamic (CFD) software in order to understand the heat and
mass transfer inside the dryer. Natural convection was the only mode
of heat transportation considered in this study as in accordance to the
idea of having a simple and maintenance-friendly design. To
accommodate the effect of low buoyancy found in natural convection
driers, a biomass burner was integrated into the solar dryer design.
Abstract: This paper seeks to develop simple yet practical and
efficient control scheme that enables cooperating arms to handle a
flexible beam. Specifically the problem studied herein is that of two
arms rigidly grasping a flexible beam and such capable of generating
forces/moments in such away as to move a flexible beam along a
predefined trajectory. The paper develops a sliding mode control law
that provides robustness against model imperfection and uncertainty.
It also provides an implicit stability proof. Simulation results for two
three joint arms moving a flexible beam, are presented to validate the
theoretical results.
Abstract: In this work, the surgical theater of a local hospital in
KSA was analyzed using simulation. The focus was on attempting to
answer questions related to how many Operating Rooms (ORs) to
open and to analyze the performance of the surgical theater in
general and mainly the Post Anesthesia Care Unit (PACU) to assist
making decisions regarding PACU staffing. The surgical theater
consists of ten operating rooms and the PACU unit which has a
maximum capacity of fifteen beds. Different sequencing rules to
sequence the surgical cases were tested and the Longest Case First
(LCF) were superior to others. The results of the different
alternatives developed and tested can be used by the manager as a
tool to plan and manage the OR and PACU
Abstract: Accurate loss minimization is the critical component
for efficient electrical distribution power flow .The contribution of
this work presents loss minimization in power distribution system
through feeder restructuring, incorporating DG and placement of
capacitor. The study of this work was conducted on IEEE
distribution network and India Electricity Board benchmark
distribution system. The executed experimental result of Indian
system is recommended to board and implement practically for
regulated stable output.
Abstract: Due to the environmental and price issues of current
energy crisis, scientists and technologists around the globe are
intensively searching for new environmentally less-impact form of
clean energy that will reduce the high dependency on fossil fuel.
Particularly hydrogen can be produced from biomass via thermochemical
processes including pyrolysis and gasification due to the
economic advantage and can be further enhanced through in-situ
carbon dioxide removal using calcium oxide. This work focuses on
the synthesis and development of the flowsheet for the enhanced
biomass gasification process in PETRONAS-s iCON process
simulation software. This hydrogen prediction model is conducted at
operating temperature between 600 to 1000oC at atmospheric
pressure. Effects of temperature, steam-to-biomass ratio and
adsorbent-to-biomass ratio were studied and 0.85 mol fraction of
hydrogen is predicted in the product gas. Comparisons of the results
are also made with experimental data from literature. The
preliminary economic potential of developed system is RM 12.57 x
106 which equivalent to USD 3.77 x 106 annually shows economic
viability of this process.
Abstract: Due to the deregulation of the Electric Supply
Industry and the resulting emergence of electricity market, the
volumes of power purchases are on the rise all over the world. In a
bid to meet the customer-s demand in a reliable and yet economic
manner, utilities purchase power from the energy market over and
above its own production. This paper aims at developing an optimal
power purchase model with two objectives viz economy and
environment ,taking various functional operating constraints such as
branch flow limits, load bus voltage magnitudes limits, unit capacity
constraints and security constraints into consideration.The price of
purchased power being an uncertain variable is modeled using fuzzy
logic. DEMO (Differential Evolution For Multi-objective
Optimization) is used to obtain the pareto-optimal solution set of the
multi-objective problem formulated. Fuzzy set theory has been
employed to extract the best compromise non-dominated solution.
The results obtained on IEEE 30 bus system are presented and
compared with that of NSGAII.
Abstract: This work concerns the topological optimization
problem for determining the optimal petroleum refinery
configuration. We are interested in further investigating and
hopefully advancing the existing optimization approaches and
strategies employing logic propositions to conceptual process
synthesis problems. In particular, we seek to contribute to this
increasingly exciting area of chemical process modeling by
addressing the following potentially important issues: (a) how the
formulation of design specifications in a mixed-logical-and-integer
optimization model can be employed in a synthesis problem to enrich
the problem representation by incorporating past design experience,
engineering knowledge, and heuristics; and (b) how structural
specifications on the interconnectivity relationships by space (states)
and by function (tasks) in a superstructure should be properly
formulated within a mixed-integer linear programming (MILP)
model. The proposed modeling technique is illustrated on a case
study involving the alternative processing routes of naphtha, in which
significant improvement in the solution quality is obtained.