Abstract: A method and apparatus for noninvasive measurement
of blood glucose concentration based on transilluminated laser beam
via the Index Finger has been reported in this paper. This method
depends on atomic gas (He-Ne) laser operating at 632.8nm
wavelength. During measurement, the index finger is inserted into the
glucose sensing unit, the transilluminated optical signal is converted
into an electrical signal, compared with the reference electrical
signal, and the obtained difference signal is processed by signal
processing unit which presents the results in the form of blood
glucose concentration. This method would enable the monitoring
blood glucose level of the diabetic patient continuously, safely and
noninvasively.
Abstract: The need in cognitive radio system for a simple, fast, and independent technique to sense the spectrum occupancy has led to the energy detection approach. Energy detector is known by its dependency on noise variation in the system which is one of its major drawbacks. In this paper, we are aiming to improve its performance by utilizing a weighted collaborative spectrum sensing, it is similar to the collaborative spectrum sensing methods introduced previously in the literature. These weighting methods give more improvement for collaborative spectrum sensing as compared to no weighting case. There is two method proposed in this paper: the first one depends on the channel status between each sensor and the primary user while the second depends on the value of the energy measured in each sensor.
Abstract: Candida spp. are common and aggressive pathogens.
Because of the growing resistance of Candida spp. to current
antifungals, novel targets, found in Candida spp. but not in humans
or other flora, have to be identified. The alternative oxidase (AOX)
is one such possibility. This enzyme is insensitive to cyanide, but is
sensitive to compounds such as salicylhydroxamic acid (SHAM),
disulfiram and n-alkyl gallates. The growth Candida albicans was
inhibited by SHAM (Ki = 9-15 mM) and cyanide (Ki = 2-4 mM),
albeit to differing extents. The rate of O2 uptake was inhibited by
less than 10% by 25 mM SHAM and by about 90% by 250 μM
KCN. Although SHAM substantially inhibited the growth of C.
albicans, it is unlikely that the inhibition of AOX was the cause.
Salicylhydroxamic acid is used therapeutically in the treatment of
urinary tract infections and urolithiasis, but it also has some potential
in the treatment of C. albicans infection.
Abstract: Chemical detection is still a continuous challenge when
it comes to designing single-walled carbon nanotube (SWCNT)
sensors with high selectivity, especially in complex chemical
environments. A perfect example of such an environment would be in
thermally oxidized soybean oil. At elevated temperatures, oil oxidizes
through a series of chemical reactions which results in the formation of
monoacylglycerols, diacylglycerols, oxidized triacylglycerols, dimers,
trimers, polymers, free fatty acids, ketones, aldehydes, alcohols,
esters, and other minor products. In order to detect the rancidity of
oxidized soybean oil, carbon nanotube chemiresistor sensors have
been coated with polyethylenimine (PEI) to enhance the sensitivity
and selectivity. PEI functionalized SWCNTs are known to have a high
selectivity towards strong electron withdrawing molecules. The
sensors were very responsive to different oil oxidation levels and
furthermore, displayed a rapid recovery in ambient air without the
need of heating or UV exposure.
Abstract: Traditional multivariate control charts assume that measurement from manufacturing processes follows a multivariate normal distribution. However, this assumption may not hold or may be difficult to verify because not all the measurement from manufacturing processes are normal distributed in practice. This study develops a new multivariate control chart for monitoring the processes with non-normal data. We propose a mechanism based on integrating the one-class classification method and the adaptive technique. The adaptive technique is used to improve the sensitivity to small shift on one-class classification in statistical process control. In addition, this design provides an easy way to allocate the value of type I error so it is easier to be implemented. Finally, the simulation study and the real data from industry are used to demonstrate the effectiveness of the propose control charts.
Abstract: This paper presents a new method of fault detection and isolation (FDI) for polymer electrolyte membrane (PEM) fuel cell (FC) dynamic systems under an open-loop scheme. This method uses a radial basis function (RBF) neural network to perform fault identification, classification and isolation. The novelty is that the RBF model of independent mode is used to predict the future outputs of the FC stack. One actuator fault, one component fault and three sensor faults have been introduced to the PEMFC systems experience faults between -7% to +10% of fault size in real-time operation. To validate the results, a benchmark model developed by Michigan University is used in the simulation to investigate the effect of these five faults. The developed independent RBF model is tested on MATLAB R2009a/Simulink environment. The simulation results confirm the effectiveness of the proposed method for FDI under an open-loop condition. By using this method, the RBF networks able to detect and isolate all five faults accordingly and accurately.
Abstract: In two studies we tested the hypothesis that the
appropriate linguistic formulation of a deontic rule – i.e. the
formulation which clarifies the monadic nature of deontic operators
- should produce more correct responses than the conditional
formulation in Wason selection task. We tested this assumption by
presenting a prescription rule and a prohibition rule in conditional
vs. proper deontic formulation. We contrasted this hypothesis with
two other hypotheses derived from social contract theory and
relevance theory. According to the first theory, a deontic rule
expressed in terms of cost-benefit should elicit a cheater detection
module, sensible to mental states attributions and thus able to
discriminate intentional rule violations from accidental rule
violations. We tested this prevision by distinguishing the two types
of violations. According to relevance theory, performance in
selection task should improve by increasing cognitive effect and
decreasing cognitive effort. We tested this prevision by focusing
experimental instructions on the rule vs. the action covered by the
rule. In study 1, in which 480 undergraduates participated, we
tested these predictions through a 2 x 2 x 2 x 2 (type of the rule x
rule formulation x type of violation x experimental instructions)
between-subjects design. In study 2 – carried out by means of a 2 x
2 (rule formulation x type of violation) between-subjects design -
we retested the hypothesis of rule formulation vs. the cheaterdetection
hypothesis through a new version of selection task in
which intentional vs. accidental rule violations were better
discriminated. 240 undergraduates participated in this study.
Results corroborate our hypothesis and challenge the contrasting
assumptions. However, they show that the conditional formulation
of deontic rules produces a lower performance than what is
reported in literature.
Abstract: In this paper, we introduce a new method for elliptical
object identification. The proposed method adopts a hybrid scheme
which consists of Eigen values of covariance matrices, Circular
Hough transform and Bresenham-s raster scan algorithms. In this
approach we use the fact that the large Eigen values and small Eigen
values of covariance matrices are associated with the major and minor
axial lengths of the ellipse. The centre location of the ellipse can be
identified using circular Hough transform (CHT). Sparse matrix
technique is used to perform CHT. Since sparse matrices squeeze zero
elements and contain a small number of nonzero elements they
provide an advantage of matrix storage space and computational time.
Neighborhood suppression scheme is used to find the valid Hough
peaks. The accurate position of circumference pixels is identified
using raster scan algorithm which uses the geometrical symmetry
property. This method does not require the evaluation of tangents or
curvature of edge contours, which are generally very sensitive to
noise working conditions. The proposed method has the advantages of
small storage, high speed and accuracy in identifying the feature. The
new method has been tested on both synthetic and real images.
Several experiments have been conducted on various images with
considerable background noise to reveal the efficacy and robustness.
Experimental results about the accuracy of the proposed method,
comparisons with Hough transform and its variants and other
tangential based methods are reported.
Abstract: Speed sensorless systems are intensively studied during recent years; this is mainly due to their economical benefit and fragility of mechanical sensors and also the difficulty of installing this type of sensor in many applications. These systems suffer from instability problems and sensitivity to parameter mismatch at low speed operation. In this paper an analysis of adaptive observer stability with stator resistance estimation is given.
Abstract: The main mission of Ezilla is to provide a friendly
interface to access the virtual machine and quickly deploy the high
performance computing environment. Ezilla has been developed by
Pervasive Computing Team at National Center for High-performance
Computing (NCHC). Ezilla integrates the Cloud middleware,
virtualization technology, and Web-based Operating System (WebOS)
to form a virtual computer in distributed computing environment. In
order to upgrade the dataset and speedup, we proposed the sensor
observation system to deal with a huge amount of data in the
Cassandra database. The sensor observation system is based on the
Ezilla to store sensor raw data into distributed database. We adopt the
Ezilla Cloud service to create virtual machines and login into virtual
machine to deploy the sensor observation system. Integrating the
sensor observation system with Ezilla is to quickly deploy experiment
environment and access a huge amount of data with distributed
database that support the replication mechanism to protect the data
security.
Abstract: This paper deals with the design, development & implementation of a temperature sensor using zigbee. The main aim of the work undertaken in this paper is to sense the temperature and to display the result on the LCD using the zigbee technology. ZigBee operates in the industrial, scientific and medical (ISM) radio bands; 868 MHz in Europe, 915 MHz in the USA and 2.4 GHz in most jurisdictions worldwide. The technology is intended to be simpler and cheaper than other WPANs such as Bluetooth. The most capable ZigBee node type is said to require only about 10 % of the software of a typical Bluetooth or Wireless Internet node, while the simplest nodes are about 2 %. However, actual code sizes are much higher, more like 50 % of the Bluetooth code size. ZigBee chip vendors have announced 128-kilobyte devices. In this work undertaken in the design & development of the temperature sensor, it senses the temperature and after amplification is then fed to the micro controller, this is then connected to the zigbee module, which transmits the data and at the other end the zigbee reads the data and displays on to the LCD. The software developed is highly accurate and works at a very high speed. The method developed shows the effectiveness of the scheme employed.
Abstract: In wireless sensor network (WSN) the use of mobile
sink has been attracting more attention in recent times. Mobile sinks
are more effective means of balancing load, reducing hotspot
problem and elongating network lifetime. The sensor nodes in WSN
have limited power supply, computational capability and storage and
therefore for continuous data delivery reliability becomes high
priority in these networks. In this paper, we propose a Reliable
Energy-efficient Data Dissemination (REDD) scheme for WSNs with
multiple mobile sinks. In this strategy, sink first determines the
location of source and then directly communicates with the source
using geographical forwarding. Every forwarding node (FN) creates a
local zone comprising some sensor nodes that can act as
representative of FN when it fails. Analytical and simulation study
reveals significant improvement in energy conservation and reliable
data delivery in comparison to existing schemes.
Abstract: The control of commutation of switched reluctance
(SR) motor has nominally depended on a physical position detector.
The physical rotor position sensor limits robustness and increases
size and inertia of the SR drive system. The paper describes a method
to overcome these limitations by using magnetization characteristics
of the motor to indicate rotor and stator teeth overlap status. The
method is using active current probing pulses of same magnitude that
is used to simulate flux linkage in the winding being probed. A
microprocessor is used for processing magnetization data to deduce
rotor-stator teeth overlap status and hence rotor position. However,
the back-of-core saturation and mutual coupling introduces overlap
detection errors, hence that of commutation control. This paper
presents the concept of the detection scheme and the effects of backof
core saturation.
Abstract: In the project FleGSens, a wireless sensor network
(WSN) for the surveillance of critical areas and properties is currently developed which incorporates mechanisms to ensure information
security. The intended prototype consists of 200 sensor nodes for
monitoring a 500m long land strip. The system is focused on ensuring
integrity and authenticity of generated alarms and availability in the
presence of an attacker who may even compromise a limited number
of sensor nodes. In this paper, two of the main protocols developed
in the project are presented, a tracking protocol to provide secure
detection of trespasses within the monitored area and a protocol for secure detection of node failures. Simulation results of networks
containing 200 and 2000 nodes as well as the results of the first prototype comprising a network of 16 nodes are presented. The focus of the simulations and prototype are functional testing of the protocols
and particularly demonstrating the impact and cost of several attacks.
Abstract: The state of melt viscosity in injection process is significantly influenced by the setting parameters due to that the shear rate of injection process is higher than other processes. How to determine plastic melt viscosity during injection process is important to understand the influence of setting parameters on the melt viscosity. An apparatus named as pressure sensor bushing (PSB) module that is used to evaluate the melt viscosity during injection process is developed in this work. The formulations to coupling melt viscosity with fill time and injection pressure are derived and then the melt viscosity is determined. A test mold is prepared to evaluate the accuracy on viscosity calculations between the PSB module and the conventional approaches. The influence of melt viscosity on the tensile strength of molded part is proposed to study the consistency of injection quality.
Abstract: This paper proposes view-point insensitive human
pose recognition system using neural network. Recognition system
consists of silhouette image capturing module, data driven database,
and neural network. The advantages of our system are first, it is
possible to capture multiple view-point silhouette images of 3D human
model automatically. This automatic capture module is helpful to
reduce time consuming task of database construction. Second, we
develop huge feature database to offer view-point insensitivity at pose
recognition. Third, we use neural network to recognize human pose
from multiple-view because every pose from each model have similar
feature patterns, even though each model has different appearance and
view-point. To construct database, we need to create 3D human model
using 3D manipulate tools. Contour shape is used to convert silhouette
image to feature vector of 12 degree. This extraction task is processed
semi-automatically, which benefits in that capturing images and
converting to silhouette images from the real capturing environment is
needless. We demonstrate the effectiveness of our approach with
experiments on virtual environment.
Abstract: We present a white LED-based optical wireless
communication systems for indoor ubiquitous sensor networks. Each
sensor node could access to the server through the PLC (Power Line
Communication)-Ethernet interface. The proposed system offers a
full-duplex wireless link by using different wavelengths to reduce the
inter-symbol interference between uplink and downlink. Through the
1-to-n optical wireless sensor network and PLC modem, the mobile
terminals send a temperature data to server. The data transmission
speed and distance are 115.2kbps and about 60cm, respectively.
Abstract: Biochemical Oxygen Demand (BOD) is a measure of
the oxygen used in bacteria mediated oxidation of organic substances
in water and wastewater. Theoretically an infinite time is required for
complete biochemical oxidation of organic matter, but the
measurement is made over 5-days at 20 0C or 3-days at 27 0C test
period with or without dilution. Researchers have worked to further
reduce the time of measurement.
The objective of this paper is to review advancement made in
BOD measurement primarily to minimize the time and negate the
measurement difficulties. Survey of literature review in four such
techniques namely BOD-BARTTM, Biosensors, Ferricyanidemediated
approach, luminous bacterial immobilized chip method.
Basic principle, method of determination, data validation and their
advantage and disadvantages have been incorporated of each of the
methods.
In the BOD-BARTTM method the time lag is calculated for the
system to change from oxidative to reductive state. BIOSENSORS
are the biological sensing element with a transducer which produces
a signal proportional to the analyte concentration. Microbial species
has its metabolic deficiencies. Co-immobilization of bacteria using
sol-gel biosensor increases the range of substrate. In ferricyanidemediated
approach, ferricyanide has been used as e-acceptor instead
of oxygen. In Luminous bacterial cells-immobilized chip method,
bacterial bioluminescence which is caused by lux genes was
observed. Physiological responses is measured and correlated to
BOD due to reduction or emission.
There is a scope to further probe into the rapid estimation of BOD.
Abstract: Electrical resistivity is a fundamental parameter of metals or electrical conductors. Since resistivity is a function of temperature, in order to completely understand the behavior of metals, a temperature dependent theoretical model is needed. A model based on physics principles has recently been developed to obtain an equation that relates electrical resistivity to temperature. This equation is dependent upon a parameter associated with the electron travel time before being scattered, and a parameter that relates the energy of the atoms and their separation distance. Analysis of the energy parameter reveals that the equation is optimized if the proportionality term in the equation is not constant but varies over the temperature range. Additional analysis reveals that the theoretical equation can be used to determine the mean free path of conduction electrons, the number of defects in the atomic lattice, and the ‘equivalent’ charge associated with the metallic bonding of the atoms. All of this analysis provides validation for the theoretical model and provides insight into the behavior of metals where performance is affected by temperatures (e.g., integrated circuits and temperature sensors).
Abstract: There are many researches to detect collision between real object and virtual object in 3D space. In general, these techniques are need to huge computing power. So, many research and study are constructed by using cloud computing, network computing, and distribute computing. As a reason of these, this paper proposed a novel fast 3D collision detection algorithm between real and virtual object using 2D intersection area. Proposed algorithm uses 4 multiple cameras and coarse-and-fine method to improve accuracy and speed performance of collision detection. In the coarse step, this system examines the intersection area between real and virtual object silhouettes from all camera views. The result of this step is the index of virtual sensors which has a possibility of collision in 3D space. To decide collision accurately, at the fine step, this system examines the collision detection in 3D space by using the visual hull algorithm. Performance of the algorithm is verified by comparing with existing algorithm. We believe proposed algorithm help many other research, study and application fields such as HCI, augmented reality, intelligent space, and so on.