Abstract: Modularized design approach can facilitate the
modeling of complex systems and support behavior analysis and
simulation in an iterative and thus complex engineering process, by
using encapsulated submodels of components and of their interfaces.
Therefore it can improve the design efficiency and simplify the
solving complicated problem. Multi-drivers off-road vehicle is
comparatively complicated. Driving-line is an important core part to a
vehicle; it has a significant contribution to the performance of a
vehicle. Multi-driver off-road vehicles have complex driving-line, so
its performance is heavily dependent on the driving-line. A typical
off-road vehicle-s driving-line system consists of torque converter,
transmission, transfer case and driving-axles, which transfer the
power, generated by the engine and distribute it effectively to the
driving wheels according to the road condition. According to its main
function, this paper puts forward a modularized approach for
designing and evaluation of vehicle-s driving-line. It can be used to
effectively estimate the performance of driving-line during concept
design stage. Through appropriate analysis and assessment method, an
optimal design can be reached. This method has been applied to the
practical vehicle design, it can improve the design efficiency and is
convenient to assess and validate the performance of a vehicle,
especially of multi-drivers off-road vehicle.
Abstract: The aim of this paper is to investigate the
performance of the developed two point block method designed for
two processors for solving directly non stiff large systems of higher
order ordinary differential equations (ODEs). The method calculates
the numerical solution at two points simultaneously and produces
two new equally spaced solution values within a block and it is
possible to assign the computational tasks at each time step to a
single processor. The algorithm of the method was developed in C
language and the parallel computation was done on a parallel shared
memory environment. Numerical results are given to compare the
efficiency of the developed method to the sequential timing. For
large problems, the parallel implementation produced 1.95 speed-up
and 98% efficiency for the two processors.
Abstract: Iran is one of the greatest producers of date in the
world. However due to lack of information about its viscoelastic
properties, much of the production downgraded during harvesting
and postharvesting processes. In this study the effect of temperature
and moisture content of product were investigated on stress
relaxation characteristics. Therefore, the freshly harvested date
(kabkab) at tamar stage were put in controlled environment chamber
to obtain different temperature levels (25, 35, 45, and 55 0C) and
moisture contents (8.5, 8.7, 9.2, 15.3, 20, 32.2 %d.b.). A texture
analyzer TAXT2 (Stable Microsystems, UK) was used to apply
uniaxial compression tests. A chamber capable to control temperature
was designed and fabricated around the plunger of texture analyzer to
control the temperature during the experiment. As a new approach a
CCD camera (A4tech, 30 fps) was mounted on a cylindrical glass
probe to scan and record contact area between date and disk.
Afterwards, pictures were analyzed using image processing toolbox
of Matlab software. Individual date fruit was uniaxially compressed
at speed of 1 mm/s. The constant strain of 30% of thickness of date
was applied to the horizontally oriented fruit. To select a suitable
model for describing stress relaxation of date, experimental data were
fitted with three famous stress relaxation models including the
generalized Maxwell, Nussinovitch, and Pelege. The constant in
mentioned model were determined and correlated with temperature
and moisture content of product using non-linear regression analysis.
It was found that Generalized Maxwell and Nussinovitch models
appropriately describe viscoelastic characteristics of date fruits as
compared to Peleg mode.
Abstract: Open Agent System platform based on High Level
Architecture is firstly proposed to support the application involving
heterogeneous agents. The basic idea is to develop different wrappers
for different agent systems, which are wrapped as federates to join a
federation. The platform is based on High Level Architecture and the
advantages for this open standard are naturally inherited, such as
system interoperability and reuse. Especially, the federal architecture
allows different federates to be heterogeneous so as to support the
integration of different agent systems. Furthermore, both implicit
communication and explicit communication between agents can be
supported. Then, as the wrapper RTI_JADE an example, the
components are discussed. Finally, the performance of RTI_JADE is
analyzed. The results show that RTI_JADE works very efficiently.
Abstract: In this paper, we investigate a blind channel estimation method for Multi-carrier CDMA systems that use a subspace decomposition technique. This technique exploits the orthogonality property between the noise subspace and the received user codes to obtain channel of each user. In the past we used Singular Value Decomposition (SVD) technique but SVD have most computational complexity so in this paper use a new algorithm called URV Decomposition, which serve as an intermediary between the QR decomposition and SVD, replaced in SVD technique to track the noise space of the received data. Because of the URV decomposition has almost the same estimation performance as the SVD, but has less computational complexity.
Abstract: In this paper we address a multi-objective scheduling problem for unrelated parallel machines. In unrelated parallel systems, the processing cost/time of a given job on different machines may vary. The objective of scheduling is to simultaneously determine the job-machine assignment and job sequencing on each machine. In such a way the total cost of the schedule is minimized. The cost function consists of three components, namely; machining cost, earliness/tardiness penalties and makespan related cost. Such scheduling problem is combinatorial in nature. Therefore, a Simulated Annealing approach is employed to provide good solutions within reasonable computational times. Computational results show that the proposed approach can efficiently solve such complicated problems.
Abstract: The protection issues in distribution systems with open and closed-loop are studied, and a generalized protection setting scheme based on the traditional over current protection theories is proposed to meet the new requirements. The setting method is expected to be easier realized using computer program, so that the on-line adaptive setting for coordination in distribution system can be implemented. An automatic setting program is created and several cases are taken into practice. The setting results are verified by the coordination curves of the protective devices which are plotted using MATLAB.
Abstract: Back-to-back static synchronous compensator (BtBSTATCOM) consists of two back-to-back voltage-source converters (VSC) with a common DC link in a substation. This configuration extends the capabilities of conventional STATCOM that bidirectional active power transfer from one bus to another is possible. In this paper, VSCs are designed in quasi multi-pulse form in which GTOs are triggered only once per cycle in PSCAD/EMTDC. The design details of VSCs as well as gate switching circuits and controllers are fully represented. Regulation modes of BtBSTATCOM are verified and tested on a multi-machine power system through different simulation cases. The results presented in the form of typical time responses show that practical PI controllers are almost robust and stable in case of start-up, set-point change, and line faults.
Abstract: Partial Discharge measurement is a very important
means of assessing the integrity of insulation systems in a High
Voltage apparatus. In compressed gas insulation systems, floating
particles can initiate partial discharge activities which adversely
affect the working of insulation. Partial Discharges below the
inception voltage also plays a crucial in damaging the integrity of
insulation over a period of time. This paper discusses the effect of
loose and fixed Copper and Nichrome wire particles on the PD
characteristics in SF6-N2 (10:90) gas mixtures at a pressure of
0.4MPa. The Partial Discharge statistical parameters and their
correlation to the observed results are discussed.
Abstract: Lean manufacturing is a production philosophy made
popular by Toyota Motor Corporation (TMC). It is globally known as
the Toyota Production System (TPS) and has the ultimate aim of
reducing cost by thoroughly eliminating wastes or muda. TPS
embraces the Just-in-time (JIT) manufacturing; achieving cost
reduction through lead time reduction. JIT manufacturing can be
achieved by implementing Pull system in the production.
Furthermore, TPS aims to improve productivity and creating
continuous flow in the production by arranging the machines and
processes in cellular configurations. This is called as Cellular
Manufacturing Systems (CMS). This paper studies on integrating the
CMS with the Pull system to establish a Big Island-Pull system
production for High Mix Low Volume (HMLV) products in an
automotive component industry. The paper will use the build-in JIT
system steps adapted from TMC to create the Pull system production
and also create a shojinka line which, according to takt time, has the
flexibility to adapt to demand changes simply by adding and taking
out manpower. This will lead to optimization in production.
Abstract: The automatic transmission (AT) is one of the most
important components of many automobile transmission systems. The
shift quality has a significant influence on the ride comfort of the
vehicle. During the AT shift process, the joint elements such as the
clutch and bands engage or disengage, linking sets of gears to create a
fixed gear ratio. Since these ratios differ between gears in a fixed gear
ratio transmission, the motion of the vehicle could change suddenly
during the shift process if the joint elements are engaged or disengaged
inappropriately, additionally impacting the entire transmission system
and increasing the temperature of connect elements.The objective was
to establish a system model for an AT powertrain using
Matlab/Simulink. This paper further analyses the effect of varying
hydraulic pressure and the associated impact on shift quality during
both engagment and disengagement of the joint elements, proving that
shift quality improvements could be achieved with appropriate
hydraulic pressure control.
Abstract: In Algeria, now, the oil pumping plants are fed with electric power by independent local sources. This type of feeding has many advantages (little climatic influence, independent operation). However it requires a qualified maintenance staff, a rather high frequency of maintenance and repair and additional fuel costs. Taking into account the increasing development of the national electric supply network (Sonelgaz), a real possibility of transfer of the local sources towards centralized sources appears.These latter cannot only be more economic but more reliable than the independent local sources as well. In order to carry out this transfer, it is necessary to work out an optimal strategy to rebuilding these networks taking in account the economic parameters and the indices of reliability.
Abstract: In this paper a novel method was presented for
evaluating the fabric pills using digital image processing techniques. This work provides a novel technique for
detecting pills and also measuring their heights, surfaces and
volumes. Surely, measuring the intensity of defects by human vision is an inaccurate method for quality control; as a result, this problem became a motivation for employing digital image processing techniques for detection of defects of fabric
surface. In the former works, the systems were just limited to measuring of the surface of defects, but in the presented
method the height and the volume of defects were also
measured, which leads to a more accurate quality control. An algorithm was developed to first, find pills and then measure their average intensity by using three criteria of height, surface
and volume. The results showed a meaningful relation
between the number of rotations and the quality of pilled fabrics.
Abstract: Mostly the systems are dealing with time varying
signals. The Power efficiency can be achieved by adapting the system
activity according to the input signal variations. In this context
an adaptive rate filtering technique, based on the level crossing sampling
is devised. It adapts the sampling frequency and the filter order
by following the input signal local variations. Thus, it correlates the
processing activity with the signal variations. Interpolation is required
in the proposed technique. A drastic reduction in the interpolation
error is achieved by employing the symmetry during the interpolation
process. Processing error of the proposed technique is
calculated. The computational complexity of the proposed filtering
technique is deduced and compared to the classical one. Results
promise a significant gain of the computational efficiency and hence
of the power consumption.
Abstract: Numerous experimental tests for post-installed anchor systems drilled in hardened concrete were conducted in order to estimate pull-out and shear strength accounting for uncertainties such as torque ratios, embedment depths and different diameters in demands. In this study, the strength of the systems was significantly changed by the effect of those three uncertainties during pull-out experimental tests, whereas the shear strength of the systems was not affected by torque ratios. It was also shown that concrete cone failure or damage mechanism was generally investigated during and after pull-out tests and in shear strength tests, mostly the anchor systems were failed prior to failure of primary structural system. Furthermore, 3D finite element model for the anchor systems was created by ABAQUS for the numerical analysis. The verification of finite element model was identical till the failure points to the load-displacement relationship specified by the experimental tests.
Abstract: This paper generalizes Yeh Lam-s shock model for
renewal shock arrivals and random threshold. Several interesting
statistical measures are explicitly obtained. A few special cases and
an optimal replacement problem are also discussed.
Abstract: This paper proposes a Web service and serviceoriented
architecture (SOA) for a computer-adaptive testing (CAT)
process on e-learning systems. The proposed architecture is
developed to solve an interoperability problem of the CAT process by
using Web service. The proposed SOA and Web service define all
services needed for the interactions between systems in order to
deliver items and essential data from Web service to the CAT Webbased
application. These services are implemented in a XML-based
architecture, platform independence and interoperability between the
Web service and CAT Web-based applications.
Abstract: Brain Computer Interface (BCI) has been recently
increased in research. Functional Near Infrared Spectroscope (fNIRs)
is one the latest technologies which utilize light in the near-infrared
range to determine brain activities. Because near infrared technology
allows design of safe, portable, wearable, non-invasive and wireless
qualities monitoring systems, fNIRs monitoring of brain
hemodynamics can be value in helping to understand brain tasks. In
this paper, we present results of fNIRs signal analysis indicating that
there exist distinct patterns of hemodynamic responses which
recognize brain tasks toward developing a BCI. We applied two
different mathematics tools separately, Wavelets analysis for
preprocessing as signal filters and feature extractions and Neural
networks for cognition brain tasks as a classification module. We
also discuss and compare with other methods while our proposals
perform better with an average accuracy of 99.9% for classification.
Abstract: A new fast correlation algorithm for calibrating the
wavelength of Optical Spectrum Analyzers (OSAs) was introduced
in [1]. The minima of acetylene gas spectra were measured and
correlated with saved theoretical data [2]. So it is possible to find the
correct wavelength calibration data using a noisy reference spectrum.
First tests showed good algorithmic performance for gas line spectra
with high noise. In this article extensive performance tests were made
to validate the noise resistance of this algorithm. The filter and
correlation parameters of the algorithm were optimized for improved
noise performance. With these parameters the performance of this
wavelength calibration was simulated to predict the resulting
wavelength error in real OSA systems. Long term simulations were
made to evaluate the performance of the algorithm over the lifetime
of a real OSA.
Abstract: Speckled images arise when coherent microwave,
optical, and acoustic imaging techniques are used to image an object, surface or scene. Examples of coherent imaging systems include synthetic aperture radar, laser imaging systems, imaging sonar
systems, and medical ultrasound systems. Speckle noise is a form of object or target induced noise that results when the surface of the object is Rayleigh rough compared to the wavelength of the illuminating radiation. Detection and estimation in images corrupted
by speckle noise is complicated by the nature of the noise and is not
as straightforward as detection and estimation in additive noise. In
this work, we derive stochastic models for speckle noise, with an emphasis on speckle as it arises in medical ultrasound images. The
motivation for this work is the problem of segmentation and tissue classification using ultrasound imaging. Modeling of speckle in this
context involves partially developed speckle model where an underlying Poisson point process modulates a Gram-Charlier series
of Laguerre weighted exponential functions, resulting in a doubly
stochastic filtered Poisson point process. The statistical distribution of partially developed speckle is derived in a closed canonical form.
It is observed that as the mean number of scatterers in a resolution cell is increased, the probability density function approaches an
exponential distribution. This is consistent with fully developed speckle noise as demonstrated by the Central Limit theorem.