Abstract: This article concerns the presentation of an integrated
method for detection of steganographic content embedded by new
unknown programs. The method is based on data mining and
aggregated hypothesis testing. The article contains the theoretical
basics used to deploy the proposed detection system and the
description of improvement proposed for the basic system idea.
Further main results of experiments and implementation details are
collected and described. Finally example results of the tests are
presented.
Abstract: Thermal behavior of fuel channel under loss of coolant accident (LOCA) is a major concern for nuclear reactor safety. LOCA along with failure of emergency cooling water system (ECC) may leads to mechanical deformations like sagging and ballooning. In order to understand the phenomenon an experiment has been carried out using 19 pin fuel element simulator. Main purpose of the experiment was to trace temperature profiles over the pressure tube, calandria tube and clad tubes of Indian Pressurized Heavy Water Reactor (IPHWR) under symmetrical and asymmetrical heat-up conditions. For simulating the fully voided scenario, symmetrical heating of pressure was carried out by injecting 13.2 KW (2 % of nominal power) to all the 19 pins and the temperatures of pressure tube, calandria tube and clad tubes were measured. During symmetrical heating the sagging of fuel channel was initiated at 460 °C and the highest temperature attained by PT was 650 °C . The decay heat from clad tubes was dissipated to moderator mainly by radiation and natural convection. The highest temperature of 680 °C was observed over the outer ring of clad tubes of fuel simulator. Again, to simulate partially voided condition, asymmetrical heating of pressure was carried out by supplying 8.0 kW power to upper 8 pins of fuel simulator and temperature profiles were measured. Along the circumference of pressure tube (PT) the highest temperature difference of 320 °C was observed, which highlights the magnitude of thermal stresses under partially voided conditions.
Abstract: The autonomous mobile robot was designed and implemented which was capable of navigating in the industrial environments and did a job of picking objects from variable height and delivering it to another location following a predefined trajectory. In developing country like Bangladesh industrial robotics is not very prevalent yet, due to the high installation cost. The objective of this project was to develop an autonomous mobile robot for industrial application using the available resources in the local market at lower manufacturing cost. The mechanical system of the robot was comprised of locomotion, gripping and elevation system. Grippers were designed to grip objects of a predefined shape. Cartesian elevation system was designed for vertical movement of the gripper. PIC18F452 microcontroller was the brain of the control system. The prototype autonomous robot was fabricated for relatively lower load than the industry and the performance was tested in a virtual industrial environment created within the laboratory to realize the effectiveness.
Abstract: A study on the performance of TCP Vegas versus
different TCP variants in homogeneous and heterogeneous wired
networks are performed via simulation experiment using network
simulator (ns-2). This performance evaluation prepared a comparison
medium for the performance evaluation of enhanced-TCP Vegas in
wired network and for wireless network. In homogeneous network,
the performance of TCP Tahoe, TCP Reno, TCP NewReno, TCP
Vegas and TCP SACK are analyzed. In heterogeneous network, the
performances of TCP Vegas against TCP variants are analyzed. TCP
Vegas outperforms other TCP variants in homogeneous wired
network. However, TCP Vegas achieves unfair throughput in
heterogeneous wired network.
Abstract: Simplified coupled engine block-crankshaft models
based on beam theory provide an efficient substitute to engine
simulation in the design process. These models require accurate
definition of the main bearing stiffness. In this paper, an investigation
of this stiffness is presented. The clearance effect is studied using a
smooth bearing model. It is manifested for low shaft displacement.
The hydrodynamic assessment model shows that the oil film has no
stiffness for low loads and it is infinitely rigid for important loads.
The deformation stiffness is determined using a suitable finite
elements model based on real CADs. As a result, a main bearing
behaviour law is proposed. This behaviour law takes into account the
clearance, the hydrodynamic sustention and the deformation stiffness.
It ensures properly the transition from the configuration low rigidity
to the configuration high rigidity.
Abstract: Fixed-point simulation results are used for the performance measure of inverting matrices using a reconfigurable processing element. Matrices are inverted using the Cholesky decomposition algorithm. The reconfigurable processing element is capable of all required mathematical operations. The fixed-point word length analysis is based on simulations of different condition numbers and different matrix sizes.
Abstract: Skin color is an important visual cue for computer
vision systems involving human users. In this paper we combine skin
color and optical flow for detection and tracking of skin regions. We
apply these techniques to gesture recognition with encouraging
results. We propose a novel skin similarity measure. For grouping
detected skin regions we propose a novel skin region grouping
mechanism. The proposed techniques work with any number of skin
regions making them suitable for a multiuser scenario.
Abstract: The purpose of study is to demonstrate how the characteristics of technology and the process required for development of technology affect technology transfer from public organisations to industry on the technology level. In addition, using the advantage of the analytic level and the novel means of measuring technology convergence, we examine the characteristics of converging technologies as compared to non-converging technologies in technology transfer process. In sum, our study finds that a technology from the public sector is likely to be transferred when its readiness level is closer to generation of profit, when its stage of life cycle is early and when its economic values is high. Our findings also show that converging technologies are less likely to be transferred.
Abstract: The aim of this study was to investigate the effects of
supplementing the diluent of roosters' semen with different levels of
olive oil on motility, viability, morphology and acrosome integrity of
chicken spermatozoa after in vitro storage for up to 72 h. Semen was
collected from 60 White Layer males (62 wk of age) kept in
separated floor pens and randomly divided into six treatment groups
(10 males in each group). Experimental groups were as follows: T1
:fresh semen, T2 : semen extended 1:1 with Al – Daraji 2 diluent
(AD2D) alone, T3 – T6 :semen samples extended 1:1 with AD2D
supplemented with 2 ml, 4 ml, 6 ml or 8 ml of olive oil / 100 ml of
diluent, respectively. Semen samples were then stored at 5 °C for 24
h, 48 h or 72 h. There was a clear influence of diluent
supplementation with olive oil on the spermatozoa motility profile;
olive oil groups (T3, T4, T5 and T6) recorded the highest scores of
mass activity and individual motility during all storage periods
compared to T1 and T2 groups. In addition, the inclusion of olive oil
into semen diluent (T3, T4, T5 and T6) gave significantly higher
percentages of viable spermatozoa, normal morphologically
spermatozoa and intact acrosomes irrespective of storage period.
These results clearly show that supplementation the diluent of
roosters' semen with olive oil can improve semen quality when
semen samples in vitro stored at 5 °C for up to 72 h.
Abstract: The aim of this research is to evaluate surface
roughness and develop a multiple regression model for surface roughness as a function of cutting parameters during the turning of
flame hardened medium carbon steel with TiN-Al2O3-TiCN coated inserts. An experimental plan of work and signal-to-noise ratio (S/N)
were used to relate the influence of turning parameters to the
workpiece surface finish utilizing Taguchi methodology. The effects
of turning parameters were studied by using the analysis of variance (ANOVA) method. Evaluated parameters were feed, cutting speed,
and depth of cut. It was found that the most significant interaction among the considered turning parameters was between depth of cut and feed. The average surface roughness (Ra) resulted by TiN-Al2O3-
TiCN coated inserts was about 2.44 μm and minimum value was 0.74 μm. In addition, the regression model was able to predict values for surface roughness in comparison with experimental values within
reasonable limit.
Abstract: In this paper we have developed a FDTD simulation
code which can treat wave propagation of a monopole antenna in a
metallic case which covers with PML, and performed a series of three
dimensional FDTD simulations of electromagnetic wave propagation
in this space .We also provide a measurement set up in antenna lab
and fortunately the simulations and measurements show good
agreement. According to simulation and measurement results, we
confirmed that the computer program which had been written in
FORTRAN, works correctly.
Abstract: The recent drive for use of performance-based methodologies in design and assessment of structures in seismic areas has significantly increased the demand for the development of reliable nonlinear inelastic static pushover analysis tools. As a result, the adaptive pushover methods have been developed during the last decade, which unlike their conventional pushover counterparts, feature the ability to account for the effect that higher modes of vibration and progressive stiffness degradation might have on the distribution of seismic storey forces. Even in advanced pushover methods, little attention has been paid to the Unsymmetric structures. This study evaluates the seismic demands for three dimensional Unsymmetric-Plan buildings determined by the Displacement-based Adaptive Pushover (DAP) analysis, which has been introduced by Antoniou and Pinho [2004]. The capability of DAP procedure in capturing the torsional effects due to the irregularities of the structures, is investigated by comparing its estimates to the exact results, obtained from Incremental Dynamic Analysis (IDA). Also the capability of the procedure in prediction the seismic behaviour of the structure is discussed.
Abstract: This paper presents a 24 watts SEPIC converter design
and control using microprocessor. SEPIC converter has advantages of
a wide input range and miniaturization caused by the low stress at
elements. There is also an advantage that the input and output are
isolated in MOSFET-off state. This paper presents the PID control
through the SEPIC converter transfer function using a DSP and the
protective circuit for fuel cell from the over-current and
inverse-voltage by using the characteristic of SEPIC converter. Then it
derives them through the experiments.
Abstract: Scheduling for the flexible job shop is very important
in both fields of production management and combinatorial
optimization. However, it quit difficult to achieve an optimal solution
to this problem with traditional optimization approaches owing to the
high computational complexity. The combining of several
optimization criteria induces additional complexity and new
problems. In this paper, a Pareto approach to solve the multi
objective flexible job shop scheduling problems is proposed. The
objectives considered are to minimize the overall completion time
(makespan) and total weighted tardiness (TWT). An effective
simulated annealing algorithm based on the proposed approach is
presented to solve multi objective flexible job shop scheduling
problem. An external memory of non-dominated solutions is
considered to save and update the non-dominated solutions during
the solution process. Numerical examples are used to evaluate and
study the performance of the proposed algorithm. The proposed
algorithm can be applied easily in real factory conditions and for
large size problems. It should thus be useful to both practitioners and
researchers.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: In this paper, an image adaptive, invisible digital
watermarking algorithm with Orthogonal Polynomials based
Transformation (OPT) is proposed, for copyright protection of digital
images. The proposed algorithm utilizes a visual model to determine
the watermarking strength necessary to invisibly embed the
watermark in the mid frequency AC coefficients of the cover image,
chosen with a secret key. The visual model is designed to generate a
Just Noticeable Distortion mask (JND) by analyzing the low level
image characteristics such as textures, edges and luminance of the
cover image in the orthogonal polynomials based transformation
domain. Since the secret key is required for both embedding and
extraction of watermark, it is not possible for an unauthorized user to
extract the embedded watermark. The proposed scheme is robust to
common image processing distortions like filtering, JPEG
compression and additive noise. Experimental results show that the
quality of OPT domain watermarked images is better than its DCT
counterpart.
Abstract: The focus of this research is in the area of the soviet period and the mission of the Russian Orthodox Church in Kazakhstan in the XIX century. There was close connection of national customs and traditions with religious practices, outlooks and attitudes. In particular, such an approach has alleged estimation by Kazakh historians of the process of Christianization of the local population. Some of them are inclined to consider the small number of Christening Kazakhs as evidence that the Russian Orthodox Church didn’t achieve its mission. The number of historians who think that the church didn’t achieve its mission has thousand over the last centuries, however our calculations of the number of Kazakhs who became Orthodox Christian is much more than other historians think. Such Christians can be divided into 3 groups: Some remained Christian until their deaths, others had two faiths and the third hid their true religions, having returned to their former belief. Therefore, to define the exact amount of Christening Kazakhs represented a challenge. Some data does not create a clear picture of the level of Christianization, constant and accurate was not collected. The data appearing in reports of spiritual attendants and civil authorities is not always authentic. Article purpose is illumination and the analysis missionary activity of Russian Orthodox Church in Kazakhstan.
Abstract: The innovative fuzzy estimator is used to estimate the
ground motion acceleration of the retaining structure in this study. The
Kalman filter without the input term and the fuzzy weighting recursive
least square estimator are two main portions of this method. The
innovation vector can be produced by the Kalman filter, and be
applied to the fuzzy weighting recursive least square estimator to
estimate the acceleration input over time. The excellent performance
of this estimator is demonstrated by comparing it with the use of
difference weighting function, the distinct levels of the measurement
noise covariance and the initial process noise covariance. The
availability and the precision of the proposed method proposed in this
study can be verified by comparing the actual value and the one
obtained by numerical simulation.
Abstract: In this paper, RSA encryption algorithm and its hardware
implementation in Xilinx-s Virtex Field Programmable Gate
Arrays (FPGA) is analyzed. The issues of scalability, flexible performance,
and silicon efficiency for the hardware acceleration of
public key crypto systems are being explored in the present work.
Using techniques based on the interleaved math for exponentiation,
the proposed RSA calculation architecture is compared to existing
FPGA-based solutions for speed, FPGA utilization, and scalability.
The paper covers the RSA encryption algorithm, interleaved multiplication,
Miller Rabin algorithm for primality test, extended Euclidean
math, basic FPGA technology, and the implementation details of
the proposed RSA calculation architecture. Performance of several
alternative hardware architectures is discussed and compared. Finally,
conclusion is drawn, highlighting the advantages of a fully flexible
& parameterized design.
Abstract: In this paper, we are presenting a new type of pointing interface for computers which provides mouse functionalities with near surface haptic feedback. Further, it can be configured as a haptic display where users may feel the basic geometrical shapes in the GUI by moving the finger on top of the device surface. These functionalities are achieved by tracking three dimensional positions of the neodymium magnet using Hall Effect sensors grid and generating like polarity haptic feedback using an electromagnet array. This interface brings the haptic sensations to the 3D space where previously it is felt only on top of the buttons of the haptic mouse implementations.