Abstract: This research is aimed to find optimal values of parameters of acacia wood chips combustion in a bubbling fluidized bed for electrification within the area of the Royal Thai Navy in Sattahip, Chonburi province, Thailand. The size of wood chips falls in the range of 25 mm in diameter. The bed temperature is set within the range of 800±10 oC with the air flow rate of 2.1-3.1 m/min corresponding to the air-fuel ratio between 0.71 to 1.03. The resulting thermal efficiency is approximately 95% with a thermal output of 474.76 kWth, which produced the electricity 0.131 kW-hr.
Abstract: In order to determine the performance and key design parameters of rocket, the erosion of nozzle throat during solid rocket motor burning have to be calculated. This study aims to predict the nozzle throat erosion in solid rocket motors according to the thrust profile of motor in operating conditions and develop a model for optimum performance of rocket. We investigate the throat radius change in the static test programs. The standard method and thrust coefficient are used for adjusting into the ideal performance for conical nozzles. Pressure and thrust data acquired from the tests are analyzed to determine the instantaneous nozzle throat diameter variation throughout the test duration. The result shows good agreement of calculated correlation comparing with measured erosion rate data showing agreement within 1.6 mm/s. Nozzle thrust coefficient loss is found approximately 24% form nozzle throat erosion during burning.
Abstract: The objective of this study is to investigate the performance of the electrocoagulation process for color and COD removal in palm oil wastewater using a 10 L batch reactor. Iron was used as electrodes and the distance between electrodes was 2 cm. The effects of operating parameters: current voltage (6, 12 and 18 volt), reaction time (5, 15, 30, 45 and 60 min) and initial pH (4 and 9) of treatment efficiency were examine. The result showed that decolorization and COD removal efficiency increased with the increase in current voltage and reaction time. The proper condition for decolorization achieved at initial pH 4 and 9 were current voltage of 12 volt, reaction time 30 min. The decolorization efficiency reached 90.4% and 88.9%, respectively. COD removal was achiveved at current voltage 12 volt, reaction time 15 min. COD removal efficiency was 89.2 % and 83.0%, respectively. From the results, to show electrocoagulation process can treat palm oil mill wastewater in both acidic and basic condition at high efficiency for color and COD removal. Consequently, electrocoagulation process can be used or applied as a post-treatment step to improve the quality of the final discharge in term of color and residual COD removal.
Abstract: HfOx based Resistive Random Access Memory (RRAM) is one of the most widely studied material stack due to its promising performances as an emerging memory technology. In this work, we systematically investigated the effect of metal capping layer by preparing sample devices with varying thickness of Ti cap and comparing their operating parameters with the help of an Agilent-B1500A analyzer.
Abstract: Microorganisms can be removed, inhibited or killed by physical agents, physical processes or chemical agents but they have their inherent disadvantages such as increased resistance against antibiotics etc. Since, plants have endless ability to synthesize aromatic substances which act as the master agents for plant defense mechanisms against microorganisms, insects and herbivores. Thus, secondary metabolites or phytochemicals obtained from plants can be used as agents of disease control nowadays. In the present study effect of different concentrations of acetone fraction of leaves and alcohol fraction of inflorescence of Euphorbia pulcherrima on various cytomorphological parameters i.e. cell number, mycelium width, conidial size, conidiophore size etc. of Aspergillus fumigatus has been studied. Change in mycelium/ hyphal cell width, conidium size, conidiophore size etc. was measured with the help of a previously calibrated oculometer. To study effect on morphology, fungal mycelium along with conidiophore and conidia were stained with cotton blue and mounted in lactophenol and observed microscopically. Inhibitory action of the acetone extract of Euphorbia pulcherrima leaf on growth of Aspergillus fumigatus was investigated. Control containing extract free medium supported profuse growth of the fungus. Although decrease in growth was observed even at 3.95μg/ml but significant inhibition of growth was started at7.81μg/ml concentration of the extract. Complete inhibition was observed at 15.62μg/ml and above. Microscopic examination revealed that at 3.95, 7.81 and 15.62μg/ml extract concentration hyphal cell width was found to be increased from 1.44μm in control to 3.86, 5.24 and 8.98 μm respectively giving a beaded appearance to the mycelium. Vesicle size was reduced from 24.78x20.08μm (control) to 11.34x10.06μm at 3.95μg/ml concentration. At 7.81 and 15.62μg/ml concentration no phialides and sterigmata were observed. Inhibitory action of the alcohol extract of inflorescence on the growth of Aspergillus fumigatus was also studied. Control containing extract free medium supported profuse growth of the fungus. Although decrease in growth was observed even at 3.95μg/ml but complete inhibition was observed at 62.5μg/ml and above. Microscopic examination revealed that hyphal cell width of Aspergillus fumigatus was found to be increased from 1.67μm in control to 5.84μm at MIC i.e. at 62.5μg/ml. Vesicle size was reduced from 44.76x 24.22μm (control) to 11.36x 6.80μm at 15.62μg/ml concentrations. At 31.25 μg/ml and 62.5μg/ml concentration no phialides and sterigmata was found. Spore germination was completely found to be inhibited at 3.95μg/ml concentration. Similarly 92.87% reduction in vesicle size was observed at 15.62μg/ml concentration. It is evident from the results that plant extracts inhibit fungal growth and this inhibition is concentration dependent.
Abstract: The industrial automation is dependent upon pneumatic control systems. The industrial units are now controlled with digital control systems to tackle the process variables like Temperature, Pressure, Flow rates and Composition.
This research work produces an evaluation of the response time fluctuations for proportional mode, proportional integral and proportional integral derivative modes of automated chemical process control. The controller output is measured for different values of gain with respect to time in three modes (P, PI and PID). In case of P-mode for different values of gain the controller output has negligible change. When the controller output of PI-mode is checked for constant gain, it can be seen that by decreasing the integral time the controller output has showed more fluctuations. The PID mode results have found to be more interesting in a way that when rate minute has changed, the controller output has also showed fluctuations with respect to time. The controller output for integral mode and derivative mode are observed with lesser steady state error, minimum offset and larger response time to control the process variable. The tuning parameters in case of P-mode are only steady state gain with greater errors with respect to controller output. The integral mode showed controller outputs with intermediate responses during integral gain (ki). By increasing the rate minute the derivative gain (kd) also increased which showed the controlled oscillations in case of PID mode and lesser overshoot.
Abstract: This work aims to generalize the integer order Sallen-Key filters into the fractional-order domain. The analysis in the case of two different fractional-order elements introduced where the general transfer function becomes four terms which is unusual in the conventional case. In addition, the effect of the transfer function parameters on the filter poles and hence the stability is introduced and closed forms for the filter critical frequencies are driven. Finally, different examples for the fractional order Sallen-Key filter design are presented with circuit simulations using ADS where a great matching between the numerical and simulation results is obtained.
Abstract: Learning the gradient of neuron's activity function
like the weight of links causes a new specification which is
flexibility. In flexible neural networks because of supervising and
controlling the operation of neurons, all the burden of the learning is
not dedicated to the weight of links, therefore in each period of
learning of each neuron, in fact the gradient of their activity function,
cooperate in order to achieve the goal of learning thus the number of
learning will be decreased considerably.
Furthermore, learning neurons parameters immunes them against
changing in their inputs and factors which cause such changing.
Likewise initial selecting of weights, type of activity function,
selecting the initial gradient of activity function and selecting a fixed
amount which is multiplied by gradient of error to calculate the
weight changes and gradient of activity function, has a direct affect
in convergence of network for learning.
Abstract: A new Meta heuristic approach called "Randomized gravitational emulation search algorithm (RGES)" for solving large size set covering problems has been designed. This algorithm is found upon introducing randomization concept along with the two of the four primary parameters -velocity- and -gravity- in physics. A new heuristic operator is introduced in the domain of RGES to maintain feasibility specifically for the set covering problem to yield best solutions. The performance of this algorithm has been evaluated on a large set of benchmark problems from OR-library. Computational results showed that the randomized gravitational emulation search algorithm - based heuristic is capable of producing high quality solutions. The performance of this heuristic when compared with other existing heuristic algorithms is found to be excellent in terms of solution quality.
Abstract: In this paper, the existence, multiplicity and
noexistence of positive solutions for a class of semipositone
discrete boundary value problems with two parameters is
studied by applying nonsmooth critical point theory and
sub-super solutions method.
Abstract: In this paper a comprehensive algorithm is presented to alleviate the undesired simultaneous effects of target maneuvering, observed glint noise distribution, and colored noise spectrum using online colored glint noise parameter estimation. The simulation results illustrate a significant reduction in the root mean square error (RMSE) produced by the proposed algorithm compared to the algorithms that do not compensate all the above effects simultaneously.
Abstract: A gradient learning method to regulate the trajectories
of some nonlinear chaotic systems is proposed. The method is
motivated by the gradient descent learning algorithms for neural
networks. It is based on two systems: dynamic optimization system
and system for finding sensitivities. Numerical results of several
examples are presented, which convincingly illustrate the efficiency
of the method.
Abstract: Themain goal of this article is to find efficient
methods for elemental and molecular analysis of living
microorganisms (algae) under defined environmental conditions and
cultivation processes. The overall knowledge of chemical
composition is obtained utilizing laser-based techniques, Laser-
Induced Breakdown Spectroscopy (LIBS) for acquiring information
about elemental composition and Raman Spectroscopy for gaining
molecular information, respectively. Algal cells were suspended in
liquid media and characterized using their spectra. Results obtained
employing LIBS and Raman Spectroscopy techniques will help to
elucidate algae biology (nutrition dynamics depending on cultivation
conditions) and to identify algal strains, which have the potential for
applications in metal-ion absorption (bioremediation) and biofuel
industry. Moreover, bioremediation can be readily combined with
production of 3rd generation biofuels. In order to use algae for
efficient fuel production, the optimal cultivation parameters have to
be determinedleading to high production of oil in selected
cellswithout significant inhibition of the photosynthetic activity and
the culture growth rate, e.g. it is necessary to distinguish conditions
for algal strain containing high amount of higher unsaturated fatty
acids. Measurements employing LIBS and Raman Spectroscopy were
utilized in order to give information about alga Trachydiscusminutus
with emphasis on the amount of the lipid content inside the algal cell
and the ability of algae to withdraw nutrients from its environment
and bioremediation (elemental composition), respectively. This
article can serve as the reference for further efforts in describing
complete chemical composition of algal samples employing laserablation
techniques.
Abstract: This paper presents an evolutionary method for designing
electronic circuits and numerical methods associated with
monitoring systems. The instruments described here have been used
in studies of weather and climate changes due to global warming, and
also in medical patient supervision. Genetic Programming systems
have been used both for designing circuits and sensors, and also for
determining sensor parameters. The authors advance the thesis that
the software side of such a system should be written in computer
languages with a strong mathematical and logic background in order
to prevent software obsolescence, and achieve program correctness.
Abstract: The performance of the Optical Code Division Multiplexing/ Wavelength Division Multiplexing (WDM/OCDM) technique for Optical Packet Switch is investigated. The impact on the performance of the impairment due to both Multiple Access Interference and Beat noise is studied. The Packet Loss Probability due to output packet contentions is evaluated as a function of the main switch and traffic parameters when Gold coherent optical codes are adopted. The Packet Loss Probability of the OCDM/WDM switch can reach 10-9 when M=16 wavelengths, Gold code of length L=511 and only 24 wavelength converters are used in the switch.
Abstract: The benefits of eco-roofs is quite well known, however there remains very little research conducted for the implementation of eco-roofs in subtropical climates such as Australia. There are many challenges facing Australia as it moves into the future, climate change is proving to be one of the leading challenges. In order to move forward with the mitigation of climate change, the impacts of rapid urbanization need to be offset. Eco-roofs are one way to achieve this; this study presents the energy savings and environmental benefits of the implementation of eco-roofs in subtropical climates. An experimental set-up was installed at Rockhampton campus of Central Queensland University, where two shipping containers were converted into small offices, one with an eco-roof and one without. These were used for temperature, humidity and energy consumption data collection. In addition, a computational model was developed using Design Builder software (state-of-the-art building energy simulation software) for simulating energy consumption of shipping containers and environmental parameters, this was done to allow comparison between simulated and real world data. This study found that eco-roofs are very effective in subtropical climates and provide energy saving of about 13% which agrees well with simulated results.
Abstract: This work presents a numerical simulation of the interaction of an incident shock wave propagates from the left to the right with a cone placed in a tube at shock. The Mathematical model is based on a non stationary, viscous and axisymmetric flow. The Discretization of the Navier-stokes equations is carried out by the finite volume method in the integral form along with the Flux Vector Splitting method of Van Leer. Here, adequate combination of time stepping parameter, CFL coefficient and mesh size level is selected to ensure numerical convergence. The numerical simulation considers a shock tube filled with air. The incident shock wave propagates to the right with a determined Mach number and crosses the cone by leaving behind it a stationary detached shock wave in front of the nose cone. This type of interaction is observed according to the time of flow.
Abstract: This paper presents a new compact analytical model of
the gate leakage current in high-k based nano scale MOSFET by
assuming a two-step inelastic trap-assisted tunneling (ITAT) process
as the conduction mechanism. This model is based on an inelastic
trap-assisted tunneling (ITAT) mechanism combined with a semiempirical
gate leakage current formulation in the BSIM 4 model. The
gate tunneling currents have been calculated as a function of gate
voltage for different gate dielectrics structures such as HfO2, Al2O3
and Si3N4 with EOT (equivalent oxide thickness) of 1.0 nm. The
proposed model is compared and contrasted with santaurus
simulation results to verify the accuracy of the model and excellent
agreement is found between the analytical and simulated data. It is
observed that proposed analytical model is suitable for different highk
gate dielectrics simply by adjusting two fitting parameters. It was
also shown that gate leakages reduced with the introduction of high-k
gate dielectric in place of SiO2.
Abstract: Nowadays, more engineering systems are using some
kind of Artificial Intelligence (AI) for the development of their
processes. Some well-known AI techniques include artificial neural
nets, fuzzy inference systems, and neuro-fuzzy inference systems
among others. Furthermore, many decision-making applications base
their intelligent processes on Fuzzy Logic; due to the Fuzzy
Inference Systems (FIS) capability to deal with problems that are
based on user knowledge and experience. Also, knowing that users
have a wide variety of distinctiveness, and generally, provide
uncertain data, this information can be used and properly processed
by a FIS. To properly consider uncertainty and inexact system input
values, FIS normally use Membership Functions (MF) that represent
a degree of user satisfaction on certain conditions and/or constraints.
In order to define the parameters of the MFs, the knowledge from
experts in the field is very important. This knowledge defines the MF
shape to process the user inputs and through fuzzy reasoning and
inference mechanisms, the FIS can provide an “appropriate" output.
However an important issue immediately arises: How can it be
assured that the obtained output is the optimum solution? How can it
be guaranteed that each MF has an optimum shape? A viable solution
to these questions is through the MFs parameter optimization. In this
Paper a novel parameter optimization process is presented. The
process for FIS parameter optimization consists of the five simple
steps that can be easily realized off-line. Here the proposed process
of FIS parameter optimization it is demonstrated by its
implementation on an Intelligent Interface section dealing with the
on-line customization / personalization of internet portals applied to
E-commerce.
Abstract: Research on the boron (B) toxicity problems had recently considerable relation, especially in the dry regions of the world. Development of resistant varieties to B toxicity is a high priority on these regions, where the soils have high levels of B. Thus, this study aimed to assessment the resistance of wheat genotypes to B toxicity using the agronomic and physiologic parameters. For this aim, a pot experiment, based on a completely randomized design with three replications, was conducted using the soil of calcareous usthochrepts. In the study, twenty different wheat genotypes of T. aestivum and T. Durum were used. Boron fertilizer at the levels of 0 (-B), 30 mg B kg-1 (+B) as H3BO3 was applied to the pots. After harvest, plant dry matter yield was recorded, and total B concentrations in tops of wheat plants were determined. The results have revealed the existence of a large genotypic variation among wheat genotypes to their physiologic and agronomic susceptibility to B toxicity.