Abstract: Control of diesel engine’s air path has drawn a lot of attention due to its multi input-multi output, closed coupled, non-linear relation. Today, precise control of amount of air to be combusted is a must in order to meet with tight emission limits and performance targets. In this study, passenger car size diesel engine is modeled by AVL Boost RT, and then simulated with standard, industry level PID controllers. Finally, linear model predictive control is designed and simulated. This study shows the importance of modeling and control of diesel engines with flexible algorithm development in computer based systems.
Abstract: Application of nanoscience in biomedical field has come across as a new era. This study involves the synthesis of nano drug carrier with antibiotic loading. Based on the founding that polydopamine (PDA) nanoparticles could be formed via self-polymerization of dopamine at alkaline pH, one-step synthesis of rifampicin coupled polydopamine (PDA-R) nanoparticles was achieved by adding rifampicin into the dopamine solution. The successful yield of PDA nanoparticles with or without the presence of rifampicin during the polymerization process was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy. Drug loading was monitored by UV-vis spectroscopy and the loading efficiency of rifampicin was calculated to be 76%. Such highly capacious nano-reservoir was found very stable with little drug leakage at pH 3.
Abstract: Measurement of the ultrasonic pulse velocity (UPV) is an important tool in diagnostic examination of concrete. In this method piezoelectric transducers are normally held in direct contact with the concrete surface. The current study aims to test the hypothesis that a preferential coupling effect might exist i.e. that the speed of sound measured depends on the couplant used. In this study, different coupling media of varying acoustic impedance were placed between the transducers and concrete samples made with constant aggregate content but with different compressive strengths. The preliminary results show that using coupling materials (both solid and a range of liquid substances) has an effect on the pulse velocity measured in a given concrete. The effect varies depending on the material used. The UPV measurements with solid coupling were higher than these from the liquid coupling at all strength levels. The tests using couplants generally recorded lower UPV values than the conventional test, except when carbon fiber composite was used, which retuned higher values. Analysis of variances (ANOVA) was performed to confirm that there are statistically significant differences between the measurements recorded using a conventional system and a coupled system.
Abstract: Reinforced concrete (RC) shear wall system of residential buildings is popular in South Korea. RC walls are subjected to axial forces in common and the effect of axial forces on the strength loss of the fire damaged walls has not been investigated. This paper aims at investigating temperature distribution on fire damaged concrete walls having different axial loads. In the experiments, a variable of specimens is axial force ratio. RC walls are fabricated with 150mm of wall thicknesses, 750mm of lengths and 1,300mm of heights having concrete strength of 24MPa. After curing, specimens are heated on one surface with ISO-834 standard time-temperature curve for 2 hours and temperature distributions during the test are measured using thermocouples inside the walls. The experimental results show that the temperature of the RC walls exposed to fire increases as axial force ratio increases. To verify the experiments, finite element (FE) models are generated for coupled temperature-structure analyses. The analytical results of thermal behaviors are in good agreement with the experimental results. The predicted displacement of the walls decreases when the axial force increases.
Abstract: To focus on the vibration mode of a cone loudspeaker,
which acts as an electroacoustic transducer, excitation experiments
were performed using two types of loudspeaker units: one employing
an impulse hammer and the other a sweep signal. The on-axis sound
pressure frequency properties of the loudspeaker were evaluated, and
the characteristic properties of the loudspeakers were successfully
determined in both excitation experiments. Moreover, under
conditions identical to the experiment conditions, a coupled analysis of
the vibration-acoustics of the cone loudspeaker was performed using
an acoustic analysis software program that considers the impact of
damping caused by air viscosity. The result of sound pressure
frequency properties with the numerical analysis are the most closely
match that measured in the excitation experiments over a wide range
of frequency bands.
Abstract: Copreneurship is a term used to describe the business
pattern of operations run by married couples who share commitment,
goals, and responsibilities in handling a business. Research conducted
overseas showed that copreneurship business activities grew quickly
and played a role in elevating families’ and nations’ socio-economic
standards. In Malaysia, copreneurship has long been cultivated by
spouses. Thus, this study aimed to explore the factors that motivate
married partners to start a copreneurship business, and who is the
dominant partner in the management of this business. The study
participants are four entrepreneurial couples who are SME business
operators selected through purposive sampling. In-depth interviews
and direct observation were used as methods of measurement for
triangulation of qualitative data in this study. The findings of the
interviews were administered using NVivo 8.0 software. The result
shows that freedom is a key factor that drives entrepreneurs to set up
copreneurship businesses, and that the husband dominates the
management aspects of the business. The study gives an overview of
the parties involved in entrepreneurship to provide understanding of
the copreneurship concept as it is practiced. This study provides
academic value by creating understanding of the importance of a
harmonious family institution specifically for forming entrepreneurs
in the familial environment in Malaysia.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: Torrefaction of biomass pellets is considered as a
useful pretreatment technology in order to convert them into a high
quality solid biofuel that is more suitable for pyrolysis, gasification,
combustion, and co-firing applications. In the course of torrefaction,
the temperature varies across the pellet, and therefore chemical
reactions proceed unevenly within the pellet. However, the
uniformity of the thermal distribution along the pellet is generally
assumed. The torrefaction process of a single cylindrical pellet is
modeled here, accounting for heat transfer coupled with chemical
kinetics. The drying sub-model was also introduced. The nonstationary
process of wood pellet decomposition is described by the
system of non-linear partial differential equations over the
temperature and mass. The model captures well the main features of
the experimental data.
Abstract: Electro-osmosis in clayey soils and sediments, for
purposes of clay consolidation, dewatering, or cleanup, and electro
injection in porous media is widespread recent decades. It is
experimentally found that the chemical properties of porous media
especially PH change the characteristics of media. Electro-osmotic
conductivity is a function of soil and grout material chemistry,
altering with time. Many numerical approaches exist to simulate the
of electro kinetic flow rate considering chemical changes. This paper
presents a simplified analytical solution for constant flow rate based
on varying electro osmotic conductivity and time dependent viscosity
for injection of colloidal silica.
Abstract: This paper focuses on the mathematical modeling for
solidification of Al alloy in a cube mold cavity to study the
solidification behavior of casting process. The parametric
investigation of solidification process inside the cavity was
performed by using computational solidification/melting model
coupled with Volume of fluid (VOF) model. The implicit filling
algorithm is used in this study to understand the overall process from
the filling stage to solidification in a model metal casting process.
The model is validated with past studied at same conditions. The
solidification process is analyzed by including the effect of pouring
velocity as well as natural convection from the wall and geometry of
the cavity. These studies show the possibility of various defects
during solidification process.
Abstract: This study evaluated the acute toxicity and tissue
distribution of intravenously administered gold nanoparticles
(AuNPs) in male rabbits. Rabbits were exposed to single dose of
AuNPs (300 μg/ kg). Toxic effects were assessed via general
behavior, hematological parameters, serum biochemical parameters,
and histopathological examination of various rabbits’ organs.
Inductively coupled plasma–mass spectrometry (ICP-MS) was used
to determine gold concentrations in tissue samples collected at
predetermined time intervals. After one week, AuNPs exerted no
obvious acute toxicity in rabbits. However, inflammatory reactions
were observed in liver, lungs and kidneys accompanied with mild
absolute neutrophilia and significant monocytosis. The highest gold
levels were found in the spleen and liver followed by lungs, and
kidneys. These results indicated that AuNPs could be distributed
extensively to various tissues in the body, but primarily in the spleen
and liver.
Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: The analytical bright two soliton solution of the 3-
coupled nonlinear Schrödinger equations with variable coefficients in
birefringent optical fiber is obtained by Darboux transformation
method. To the design of ultra-speed optical devices, Soliton
interaction and control in birefringence fiber is investigated. Lax pair
is constructed for N coupled NLS system through AKNS method.
Using two-soliton solution, we demonstrate different interaction
behaviors of solitons in birefringent fiber depending on the choice of
control parameters. Our results shows that interactions of optical
solitons have some specific applications such as construction of logic
gates, optical computing, soliton switching, and soliton amplification
in wavelength division multiplexing (WDM) system.
Abstract: A Multi-dimensional computational fluid dynamics
(CFD) two-phase model was developed with the aim to simulate
the in-core coolant circuit of a pressurized heavy water reactor
(PHWR) of a commercial nuclear power plant (NPP). Due to the
fact that this PHWR is a Reactor Pressure Vessel type (RPV),
three-dimensional (3D) detailed modelling of the large reservoirs of
the RPV (the upper and lower plenums and the downcomer) were
coupled with an in-house finite volume one-dimensional (1D) code
in order to model the 451 coolant channels housing the nuclear fuel.
Regarding the 1D code, suitable empirical correlations for taking into
account the in-channel distributed (friction losses) and concentrated
(spacer grids, inlet and outlet throttles) pressure losses were used.
A local power distribution at each one of the coolant channels
was also taken into account. The heat transfer between the coolant
and the surrounding moderator was accurately calculated using a
two-dimensional theoretical model. The implementation of subcooled
boiling and condensation models in the 1D code along with the use
of functions for representing the thermal and dynamic properties of
the coolant and moderator (heavy water) allow to have estimations
of the in-core steam generation under nominal flow conditions for a
generic fission power distribution. The in-core mass flow distribution
results for steady state nominal conditions are in agreement with the
expected from design, thus getting a first assessment of the coupled
1/3D model. Results for nominal condition were compared with
those obtained with a previous 1/3D single-phase model getting more
realistic temperature patterns, also allowing visualize low values of
void fraction inside the upper plenum. It must be mentioned that the
current results were obtained by imposing prescribed fission power
functions from literature. Therefore, results are showed with the aim
of point out the potentiality of the developed model.
Abstract: The wider growing Finite Element Method (FEM)
application is caused by its benefits of cost saving and environment
friendly. Also, by using FEM a deep understanding of certain
phenomenon can be achieved. This paper observed the role of
material properties and volumetric change when Solid State Phase
Transformation (SSPT) takes place in residual stress formation due to
a welding process of ferritic steels through coupled Thermo-
Metallurgy-Mechanical (TMM) analysis. The correctness of FEM residual stress prediction was validated by
experiment. From parametric study of the FEM model, it can be
concluded that the material properties change tend to over-predicts
residual stress in the weld center whilst volumetric change tend to
underestimates it. The best final result is the compromise of both by
incorporates them in the model which has a better result compared to
a model without SSPT.
Abstract: In this study, we investigated numerically heat
transfer by mixed convection coupled to radiation in a square cavity;
the upper horizontal wall is movable. The purpose of this study is to
see the influence of the emissivity ε and the varying of the
Richardson number Ri on the variation of average Nusselt number
Nu. The vertical walls of the cavity are differentially heated, the left
wall is maintained at a uniform temperature higher than the right
wall, and the two horizontal walls are adiabatic. The finite volume
method is used for solving the dimensionless Governing Equations.
Emissivity values used in this study are ranged between 0 and 1, the
Richardson number in the range 0.1 to 10. The Rayleigh number is
fixed to Ra=104 and the Prandtl number is maintained constant
Pr=0.71. Streamlines, isothermal lines and the average Nusselt
number are presented according to the surface emissivity. The results
of this study show that the Richardson number Ri and emissivity ε
affect the average Nusselt number.
Abstract: At the present work, highly transparent strip type
quasi-solid state dye-sensitized solar cells (DSSCs) were fabricated
through inkjet printing using nanocomposite TiO2 inks as raw
materials and tested under outdoor illumination conditions. The cells,
which can be considered as the structural units of large area modules,
were fully characterized electrically and electrochemically and after
the evaluation of the received results a large area DSSC module was
manufactured. The module design was a sandwich Z-interconnection
where the working electrode is deposited on one conductive glass and
the counter electrode on a second glass. Silver current collective
fingers were printed on the conductive glasses to make the internal
electrical connections and the adjacent cells were connected in series
and finally insulated using a UV curing resin to protect them from the
corrosive (I-/I3-) redox couple of the electrolyte. Finally, outdoor tests
were carried out to the fabricated dye-sensitized solar module and its
performance data were collected and assessed.
Abstract: To study the dynamic mechanics response of asphalt
pavement under the temperature load and vehicle loading, asphalt
pavement was regarded as multilayered elastic half-space system, and
theory analysis was conducted by regarding dynamic modulus of
asphalt mixture as the parameter. Firstly, based on the dynamic
modulus test of asphalt mixture, function relationship between the
dynamic modulus of representative asphalt mixture and temperature
was obtained. In addition, the analytical solution for thermal stress in
single layer was derived by using Laplace integral transformation and
Hankel integral transformation respectively by using thermal
equations of equilibrium. The analytical solution of calculation model
of thermal stress in asphalt pavement was derived by transfer matrix
of thermal stress in multilayer elastic system. Finally, the variation of
thermal stress in pavement structure was analyzed. The result shows
that there is obvious difference between the thermal stress based on
dynamic modulus and the solution based on static modulus. So the
dynamic change of parameter in asphalt mixture should be taken into
consideration when theoretical analysis is taken out.
Abstract: This article describes the results of research focused
on quality of railway freight transport services. Improvement of these
services has a crucial importance in customer considering on the
future use of railway transport. Processes filling the customer
demands and output quality assessment were defined as a part of the
research. In this contribution is introduced the map of quality
planning and the algorithm of applied methodology. It characterizes a
model which takes into account characters of transportation with
linking a perception services quality in ordinary and extraordinary
operation. Despite the fact that rail freight transport has its solid
position in the transport market, lots of carriers worldwide have been
experiencing a stagnation for a couple of years. Therefore, specific
results of the research have a significant importance and belong to
numerous initiatives aimed to develop and support railway transport
not only by creating a single railway area or reducing noise but also
by promoting railway services. This contribution is focused also on
the application of dynamic quality models which represent an
innovative method of evaluation quality services. Through this
conception, time factor, expected, and perceived quality in each
moment of the transportation process can be taken into account.
Abstract: In this numerical study, effects of using Al2O3-water
nanofluid on the rate of heat transfer have been investigated. Physical
model is a square enclosure with insulated top and bottom horizontal
walls, while the vertical walls are kept at different constant
temperatures. Two appropriate models are used to evaluate the
viscosity and thermal conductivity of nanofluid. The governing
stream-vorticity equations are solved using a second order central
finite difference scheme, coupled to the conservation of mass and
energy. The study has been carried out for the nanoparticle diameter
30, 60 and 90 nm and the solid volume fraction 0 to 0.04. Results are
presented by average Nusselt number and normalized Nusselt number
in different range of φ and D for mixed convection dominated
regime. It is found that different heat transfer rate is predicted when
the effect of nanoparticle diameter is taken into account.