Abstract: Environmental performance of the U.S. States is investigated for the period of 1990 – 2007 using Stochastic Frontier Analysis (SFA). The SFA accounts for both efficiency measure and stochastic noise affecting a frontier. The frontier is formed using indicators of GDP, energy consumption, population, and CO2 emissions. For comparability, all indicators are expressed as ratios to total. Statistical information of the Energy Information Agency of the United States is used. Obtained results reveal the bell - shaped dynamics of environmental efficiency scores. The average efficiency scores rise from 97.6% in 1990 to 99.6% in 1999, and then fall to 98.4% in 2007. The main factor is insufficient decrease in the rate of growth of CO2 emissions with regards to the growth of GDP, population and energy consumption. Data for 2008 following the research period allow for an assumption that the environmental performance of the U.S. States has improved in the last years.
Abstract: In this paper, an analysis is presented, which
demonstrates the effect pre-logic factoring could have on an
automated combinational logic synthesis process succeeding it. The
impact of pre-logic factoring for some arbitrary combinatorial
circuits synthesized within a FPGA based logic design environment
has been analyzed previously. This paper explores a similar effect,
but with the non-regenerative logic synthesized using elements of a
commercial standard cell library. On an overall basis, the results
obtained pertaining to the analysis on a variety of MCNC/IWLS
combinational logic benchmark circuits indicate that pre-logic
factoring has the potential to facilitate simultaneous power, delay and
area optimized synthesis solutions in many cases.
Abstract: This study reports the preparation of soft magnetic ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213 mm and, with a thickness of approximately 22 μm 2 μm. The microstructure and magnetic properties of the ribbons were characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide ribbon, the magnetic responses are not uniformly distributed. To understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: One of the main and responsible units of Sulzer
projectile loom is picking mechanism. It is specifically designed to
accelerate projectile to speed of 25 m / s. Initial speed projectile of
Sulzer projectile loom is independent of speed loom and determined
the potential energy torsion rod. This paper investigates the dynamics
picking mechanism of Sulzer projectile loom during its discharge. A
result of calculation model, we obtain the law of motion lever of
picking mechanism during its discharge. Construction of dynamic
model the picking mechanism of Sulzer projectile loom on software
complex SimulationX can make calculations for different thickness
of torsion rods taking into account the backlashes in the connections,
the dissipative forces and resistance forces
Abstract: Energy intensity(energy consumption intensity) is a
global index which computes the required energy for producing a
specific value of goods and services in each country. It is computed
in terms of initial energy supply or final energy consumption. In this
study (research) Divisia method is used to decompose energy
consumption and energy intensity. This method decomposes
consumption and energy intensity to production effects, structural
and net intensity and could be done as time series or two-periodical.
This study analytically investigates consumption changes and energy
intensity on economical sectors of Iran and more specific on road
transportation(rail road and road).Our results show that the
contribution of structural effect (change in economical activities
combination) is very low and the effect of net energy consumption
has the higher contribution in consumption changes and energy
intensity. In other words, the high consumption of energy is due to
Intensity of energy consumption and is not to structural effect of
transportation sector.
Abstract: Segmentation is an important step in medical image
analysis and classification for radiological evaluation or computer
aided diagnosis. The CAD (Computer Aided Diagnosis ) of lung CT
generally first segment the area of interest (lung) and then analyze
the separately obtained area for nodule detection in order to
diagnosis the disease. For normal lung, segmentation can be
performed by making use of excellent contrast between air and
surrounding tissues. However this approach fails when lung is
affected by high density pathology. Dense pathologies are present in
approximately a fifth of clinical scans, and for computer analysis
such as detection and quantification of abnormal areas it is vital that
the entire and perfectly lung part of the image is provided and no
part, as present in the original image be eradicated. In this paper we
have proposed a lung segmentation technique which accurately
segment the lung parenchyma from lung CT Scan images. The
algorithm was tested against the 25 datasets of different patients
received from Ackron Univeristy, USA and AGA Khan Medical
University, Karachi, Pakistan.
Abstract: This paper examines the issues, the dangers and the
saving graces of life in a transparent global community where there is
truly “no place to hide". In recent years, social networks and online
groups have transformed issues of privacy and the ways in which we
perceive and interact with others. The idea of reputation is critical to
this dynamic. The discussion begins with a brief etymological history
of the concept of reputation and moves to an exploration of how and
why online communication changes our basic nature, our various
selves and the Bakhtin idea of the polyphonic nature of truth. The
discussion considers the damaging effects of bullying and gossip,
both of which constitute an assault on reputation and the latter of
which is not limited to the lifetime of the person. It concludes with
guidelines and specific recommendations.
Abstract: This paper highlights the importance of integrating social and technical approach (which is so called a “hybrid socio-technical approach") as one innovative and strategic program to support the social development in geodisaster prone area in Indonesia. Such program mainly based on public education and community participation as a partnership program by the University, local government and may also with the private company and/ or local NGO. The indigenous, simple and low cost technology has also been introduced and developed as a part of the hybrid sociotechnical system, in order to ensure the life and environmental protection, with respect to the sustainable human and social development.
Abstract: The empirical mode decomposition (EMD) represents any time series into a finite set of basis functions. The bases are termed as intrinsic mode functions (IMFs) which are mutually orthogonal containing minimum amount of cross-information. The EMD successively extracts the IMFs with the highest local frequencies in a recursive way, which yields effectively a set low-pass filters based entirely on the properties exhibited by the data. In this paper, EMD is applied to explore the properties of the multi-year air temperature and to observe its effects on climate change under global warming. This method decomposes the original time-series into intrinsic time scale. It is capable of analyzing nonlinear, non-stationary climatic time series that cause problems to many linear statistical methods and their users. The analysis results show that the mode of EMD presents seasonal variability. The most of the IMFs have normal distribution and the energy density distribution of the IMFs satisfies Chi-square distribution. The IMFs are more effective in isolating physical processes of various time-scales and also statistically significant. The analysis results also show that the EMD method provides a good job to find many characteristics on inter annual climate. The results suggest that climate fluctuations of every single element such as temperature are the results of variations in the global atmospheric circulation.
Abstract: This is an applied research to propose the method for
price quotation for a contract electronics manufacturer. It has had a
precise price quoting method but such method could not quickly
provide a result as the customer required. This reduces the ability of
company to compete in this kind of business. In this case, the cause
of long time quotation process was analyzed. A lot of product
features have been demanded by customer. By checking routine
processes, it was found that high fraction of quoting time was used
for production time estimating which has effected to the
manufacturing or production cost. Then the historical data of
products including types, number of components, assembling
method, and their assembling time were used to analyze the key
components affecting to production time. The price quoting model
then was proposed. The implementation of proposed model was able
to remarkably reduce quoting time with an acceptable required
precision.
Abstract: In this work, we incorporated a quartic bond potential
into a coarse-grained bead-spring model to study lubricant adsorption
on a solid surface as well as depletion instability. The surface tension
density and the number density profiles were examined to verify the
solid-liquid and liquid-vapor interfaces during heat treatment. It was
found that both the liquid-vapor interfacial thickness and the
solid-vapor separation increase with the temperatureT* when T*is
below the phase transition temperature Tc
*. At high temperatures
(T*>Tc
*), the solid-vapor separation decreases gradually as the
temperature increases. In addition, we evaluated the lubricant weight
and bond loss profiles at different temperatures. It was observed that
the lubricant desorption is favored over decomposition and is the main
cause of the lubricant failure at the head disk interface in our
simulations.
Abstract: The purpose of the study reported here was designing Information Dissemination System (IDS) based E-learning in agricultural of Iran. A questionnaire was developed to designing Information Dissemination System. The questionnaire was distributed to 96 extension agents who work for Management of Extension and Farming System of Khuzestan province of Iran. Data collected were analyzed using the Statistical Package for the Social Sciences (SPSS). Appropriate statistical procedures for description (frequencies, percent, means, and standard deviations) were used. In this study there was a significant relationship between the age , IT skill and knowledge, years of extension work, the extend of information seeking motivation, level of job satisfaction and level of education with use of information technology by extension agent. According to extension agents five factors were ranked respectively as five top essential items to designing Information Dissemination System (IDS) based E-learning in agricultural of Iran. These factors include: 1) Establish communication between farmers, coordinators (extension agents), agricultural experts, research centers, and community by information technology. 2) The communication between all should be mutual. 3) The information must be based farmers need. 4) Internet used as a facility to transfer the advanced agricultural information to the farming community. 5) Farmers can be illiterate and speak a local and they are not expected to use the system directly. Knowledge produced by the agricultural scientist must be transformed in to computer understandable presentation. To designing Information Dissemination System, electronic communication, in the agricultural society and rural areas must be developed. This communication must be mutual between all factors.
Abstract: The design of distributed systems involves dividing the system into partitions (or components) and then allocating these partitions to physical nodes. There have been several techniques proposed for both the partitioning and allocation processes. These existing techniques suffer from a number of limitations including lack of support for replication. Replication is difficult to use effectively but has the potential to greatly improve the performance of a distributed system. This paper presents a new technique technique for allocating objects in order to improve performance in a distributed system that supports replication. The performance of the proposed technique is demonstrated and tested on an example system. The performance of the new technique is compared with the performance of an existing technique in order to demonstrate both the validity and superiority of the new technique when developing a distributed system that can utilise object replication.
Abstract: Sulphur dioxide is a harmful gaseous product that
needs to be minimized in the atmosphere. This research work
investigates the use of zeolite as a possible additive that can improve
the sulphur dioxide capture in wet flue gas desulphurisation
dissolution process. This work determines the effect of temperature,
solid to liquid ratio, acid concentration and stirring speed on the
leaching of zeolite using a pH stat apparatus. The atomic absorption
spectrometer was used to measure the calcium ions from the solution.
It was found that the dissolution rate of zeolite decreased with
increase in solid to liquid ratio and increases with increase in
temperature, stirring speed and acid concentration. The activation
energy for the dissolution rate of zeolite in hydrochloric acid was
found to be 9.29kJ/mol. and therefore the product layer diffusion was
the rate limiting step.
Abstract: Monitoring lightning electromagnetic pulses (sferics) and other terrestrial as well as extraterrestrial transient radiation signals is of considerable interest for practical and theoretical purposes in astro- and geophysics as well as meteorology. Managing a continuous flow of data, automation of the analysis and classification process is important. Features based on a combination of wavelet and statistical methods proved efficient for this task and serve as input into a radial basis function network that is trained to discriminate transient shapes from pulse like to wave like. We concentrate on signals in the Very Low Frequency (VLF, 3 -30 kHz) range in this paper, but the developed methods are independent of this specific choice.
Abstract: F-actin fibrils are the cytoskeleton of osteocytes. They react in a dynamic manner to mechanical loading, and strength and
reposition their efforts to reinforce the cells structure. We hypothesize that f-actin is temporarly disrupted after loading and repolymerizes
in a new orientation to oppose the applied load. In vitro studies are conducted to determine f-actin disruption after varying mechanical stimulus parameters that are known to affect bone
formation. Results indicate that the f-actin cytoskeleton is disrupted in vitro as a function of applied mechanical stimulus parameters and
that the f-actin bundles reassemble after loading induced disruption
within 3 minutes after cessation of loading. The disruption of the factin
cytoskeleton depends on the magnitude of stretch, the numbers
of loading cycles, frequency, the insertion of rest between loading
cycles and extracellular calcium. In vivo studies also demonstrate
disruption of the f-actin cytoskeleton in cells embedded in the bone
matrix immediately after mechanical loading. These studies suggest
that adaptation of the f-actin fiber bundles of the cytoskeleton in
response to applied loads occurs by disruption and subsequent repolymerization.
Abstract: A self-evolution algorithm for optimizing neural networks using a combination of PSO and JPSO is proposed. The algorithm optimizes both the network topology and parameters simultaneously with the aim of achieving desired accuracy with less complicated networks. The performance of the proposed approach is compared with conventional back-propagation networks using several synthetic functions, with better results in the case of the former. The proposed algorithm is also implemented on slope stability problem to estimate the critical factor of safety. Based on the results obtained, the proposed self evolving network produced a better estimate of critical safety factor in comparison to conventional BPN network.
Abstract: Teachers form the backbone of any educational system, hence selecting qualified candidates is very crucial. In Malaysia, the decision making in the selection process involves a few stages: Initial filtering through academic achievement, taking entry examination and going through an interview session. The last stage is the most challenging since it highly depends on human judgment. Therefore, this study sought to identify the selection criteria for teacher candidates that form the basis for an efficient multi-criteria teacher-candidate selection model for that last stage. The relevant criteria were determined from the literature and also based on expert input that is those who were involved in interviewing teacher candidates from a public university offering the formal training program. There are three main competency criteria that were identified which are content of knowledge, communication skills and personality. Further, each main criterion was divided into a few subcriteria. The Analytical Hierarchy Process (AHP) technique was employed to allocate weights for the criteria and later, integrated a Simple Weighted Average (SWA) scoring approach to develop the selection model. Subsequently, a web-based Decision Support System was developed to assist in the process of selecting the qualified teacher candidates. The Teacher-Candidate Selection (TeCaS) system is able to assist the panel of interviewers during the selection process which involves a large amount of complex qualitative judgments.
Abstract: Young people have a high prevalence of mental health
problems, yet tend not to seek help. Trusted adults in young people-s
lives, such as teachers and sports coaches, can make a major positive
contribution to the mental health of young people. Teachers and
sports coaches may be in a position to be effective in supporting
young people-s mental health through promotion, prevention and
early intervention. This study reports findings from interviews with
21 teachers and 13 sports coaches of young people aged 12 to 18 in
Canberra, Australia, regarding their perceptions of the relevance and
effectiveness of their role in supporting young people-s mental
health. Both teachers and coaches perceived having influential but
slightly different roles to play in supporting mental health. There may
be potential to elevate the influence of teachers and coaches as
sources of support for young people and their mental health care.
Abstract: The human body has a complex system of innate and adaptive mechanisms for combating infection. This article discusses the role and relative effectiveness of these mechanisms in relation to small pox and AIDS.