Abstract: This paper presents the doping profile measurement
and characterization technique for the pocket implanted nano scale
n-MOSFET. Scanning capacitance microscopy and atomic force
microscopy have been used to image the extent of lateral dopant
diffusion in MOS structures. The data are capacitance vs. voltage
measurements made on a nano scale device. The technique is nondestructive
when imaging uncleaved samples. Experimental data from
the published literature are presented here on actual, cleaved device
structures which clearly indicate the two-dimensional dopant profile
in terms of a spatially varying modulated capacitance signal. Firstorder
deconvolution indicates the technique has much promise for
the quantitative characterization of lateral dopant profiles. The pocket
profile is modeled assuming the linear pocket profiles at the source
and drain edges. From the model, the effective doping concentration
is found to use in modeling and simulation results of the various
parameters of the pocket implanted nano scale n-MOSFET. The
potential of the technique to characterize important device related
phenomena on a local scale is also discussed.
Abstract: Reinforced concrete crash barriers used in road traffic
must meet a number of criteria. Crash barriers are laid lengthwise,
one behind another, and joined using specially designed steel locks.
While developing BSV reinforced concrete crash barriers (type
ŽPSV), experiments and calculations aimed to optimize the shape of
a newly designed lock and the reinforcement quantity and
distribution in a crash barrier were carried out. The tension carrying
capacity of two parallelly joined locks was solved experimentally.
Based on the performed experiments, adjustments of nonlinear
properties of steel were performed in the calculations. The obtained
results served as a basis to optimize the lock design using a
computational model that takes into account the plastic behaviour of
steel and the influence of the surrounding concrete [6]. The response
to the vehicle impact has been analyzed using a specially elaborated
complex computational model, comprising both the nonlinear model
of the damping wall or crash barrier and the detailed model of the
vehicle [7].
Abstract: A different concept for designing and detailing of
reinforced concrete precast frame structures is analyzed in this paper.
The new detailing of the joints derives from the special hybrid
moment frame joints. The special reinforcements of this alternative
detailing, named modified special hybrid joint, are bondless with
respect to both column and beams. Full scale tests were performed on
a plan model, which represents a part of 5 story structure, cropped in
the middle of the beams and columns spans. Theoretical approach
was developed, based on testing results on twice repaired model,
subjected to lateral seismic type loading. Discussion regarding the
modified special hybrid joint behavior and further on widening
research needed concludes the presentation.
Abstract: The objective of this paper is twofold: (1) discuss and
analyze the successful case studies worldwide, and (2) identify the
similarities and differences of case studies worldwide. Design
methodology/approach: The nature of this research is mainly method
qualitative (multi-case studies, literature review). This investigation
uses ten case studies, and the data was mainly collected and
organizational documents from the international countries. Finding:
The finding of this research can help incubator manager, policy
maker and government parties for successful implementation.
Originality/value: This paper contributes to the current literate review
on the best practices worldwide. Additionally, it presents future
perspective for academicians and practitioners.
Abstract: The Maximum Weighted Independent Set (MWIS)
problem is a classic graph optimization NP-hard problem. Given an
undirected graph G = (V, E) and weighting function defined on the
vertex set, the MWIS problem is to find a vertex set S V whose total
weight is maximum subject to no two vertices in S are adjacent. This
paper presents a novel approach to approximate the MWIS of a graph
using minimum weighted vertex cover of the graph. Computational
experiments are designed and conducted to study the performance
of our proposed algorithm. Extensive simulation results show that
the proposed algorithm can yield better solutions than other existing
algorithms found in the literature for solving the MWIS.
Abstract: The problem of delay-range-dependent exponential synchronization is investigated for Lur-e master-slave systems with delay feedback control and Markovian switching. Using Lyapunov- Krasovskii functional and nonsingular M-matrix method, novel delayrange- dependent exponential synchronization in mean square criterions are established. The systems discussed in this paper is advanced system, and takes all the features of interval systems, Itˆo equations, Markovian switching, time-varying delay, as well as the environmental noise, into account. Finally, an example is given to show the validity of the main result.
Abstract: The rotation of starting pitchers is a strategic issue
which has a significant impact on the performance of a professional
team. Choosing an optimal starting pitcher from among many
alternatives is a multi-criteria decision-making (MCDM) problem. In
this study, a model using the Analytic Hierarchy Process (AHP) and
Technique for Order Performance by Similarity to the Ideal Solution
(TOPSIS) is proposed with which to arrange the starting pitcher
rotation for teams of the Chinese Professional Baseball League. The
AHP is used to analyze the structure of the starting pitcher selection
problem and to determine the weights of the criteria, while the
TOPSIS method is used to make the final ranking. An empirical
analysis is conducted to illustrate the utilization of the model for the
starting pitcher rotation problem. The results demonstrate the
effectiveness and feasibility of the proposed model.
Abstract: The aim of this paper is to present current and future
procedures in castings procurement. Differences in procurement are
highlighted. The supplier selection criteria used in practice is
compared to literature findings. Different trends related to supply
chains are presented and it is described how they are reflected in
reality to castings procurement. To fulfil the aim, interviews were
conducted in nine companies using castings. It was found that largest
casting users have the most subcontractor foundries and it is more
typical that they have multiple suppliers for the same parts. Currently
only two companies out of nine purchase castings outside Europe,
but the others are also progressing in the same direction. The main
reason is the need to lower purchasing costs. Another trend is that all
companies want to buy cast components or sub-assemblies instead of
raw castings from foundries. It was found that price is a main
supplier selection criterion. All companies use competitive bidding in
supplier selection.
Abstract: A Picard-Newton iteration method is studied to accelerate the numerical solution procedure of a class of two-dimensional nonlinear coupled parabolic-hyperbolic system. The Picard-Newton iteration is designed by adding higher-order terms of small quantity to an existing Picard iteration. The discrete functional analysis and inductive hypothesis reasoning techniques are used to overcome difficulties coming from nonlinearity and coupling, and theoretical analysis is made for the convergence and approximation properties of the iteration scheme. The Picard-Newton iteration has a quadratic convergent ratio, and its solution has second order spatial approximation and first order temporal approximation to the exact solution of the original problem. Numerical tests verify the results of the theoretical analysis, and show the Picard-Newton iteration is more efficient than the Picard iteration.
Abstract: Nowadays, a passenger car suspension must has high
performance criteria with light weight, low cost, and low energy
consumption. Pilot controlled proportional valve is designed and
analyzed to get small pressure change rate after blow-off, and to get a
fast response of the damper, a reverse damping mechanism is adapted.
The reverse continuous variable damper is designed as a HS-SH
damper which offers good body control with reduced transferred input
force from the tire, compared with any other type of suspension
system. The damper structure is designed, so that rebound and
compression damping forces can be tuned independently, of which the
variable valve is placed externally. The rate of pressure change with
respect to the flow rate after blow-off becomes smooth when the fixed
orifice size increases, which means that the blow-off slope is
controllable using the fixed orifice size. Damping forces are measured
with the change of the solenoid current at the different piston
velocities to confirm the maximum hysteresis of 20 N, linearity, and
variance of damping force. The damping force variance is wide and
continuous, and is controlled by the spool opening, of which scheme is
usually adapted in proportional valves. The reverse continuous
variable damper developed in this study is expected to be utilized in
the semi-active suspension systems in passenger cars after its
performance and simplicity of the design is confirmed through a real
car test.
Abstract: In the last few years, several steps were taken in order
to improve the quality of corporate governance for Romanian listed
companies. Higher standards of corporate governance is documented
in the literature to lead to a better information environment, and,
consequently, to increase analysts forecast accuracy. Accordingly, the
purpose of this paper is to investigate the extent to which corporate
governance policies affect analysts forecasts for companies listed on
Bucharest Stock Exchange. The results showed that there is indeed a
negative correlation between a corporate governance index – used as
a proxy for the quality of corporate governance practices - and
analysts forecast errors.
Abstract: In most cases, it is considerably difficult to directly measure structural vibration with a lot of sensors because of complex
geometry, time and equipment cost. For this reason, this paper deals
with the problem of locating sensors on a plate model by four advanced sensor placement optimization (S.P.O) techniques. It also
suggests the evaluation index representing the characteristic of orthogonal between each of natural modes. The index value provides the assistance to selecting of proper S.P.O technique and optimal
positions for monitoring of dynamic systems without the experiment.
Abstract: The cellular network is one of the emerging areas of
communication, in which the mobile nodes act as member for one
base station. The cluster based communication is now an emerging
area of wireless cellular multimedia networks. The cluster renders
fast communication and also a convenient way to work with
connectivity. In our scheme we have proposed an optimization
technique for the fuzzy cluster nodes, by categorizing the group
members into three categories like long refreshable member, medium
refreshable member and short refreshable member. By considering
long refreshable nodes as static nodes, we compute the new
membership values for the other nodes in the cluster. We compare
their previous and present membership value with the threshold value
to categorize them into three different members. By which, we
optimize the nodes in the fuzzy clusters. The simulation results show
that there is reduction in the cluster computational time and
iterational time after optimization.
Abstract: This paper describes a novel method for automatic
estimation of the contours of weld defect in radiography images.
Generally, the contour detection is the first operation which we apply
in the visual recognition system. Our approach can be described as a
region based maximum likelihood formulation of parametric
deformable contours. This formulation provides robustness against
the poor image quality, and allows simultaneous estimation of the
contour parameters together with other parameters of the model.
Implementation is performed by a deterministic iterative algorithm
with minimal user intervention. Results testify for the very good
performance of the approach especially in synthetic weld defect
images.
Abstract: In this paper, we present the preconditioned mixed-type
splitting iterative method for solving the linear systems, Ax = b,
where A is a Z-matrix. And we give some comparison theorems
to show that the convergence rate of the preconditioned mixed-type
splitting iterative method is faster than that of the mixed-type splitting
iterative method. Finally, we give a numerical example to illustrate
our results.
Abstract: By means of Contractor Iteration Method, we solve and visualize the Lane-Emden(-Fowler) equation Δu + up = 0, in Ω, u = 0, on ∂Ω. It is shown that the present method converges quadratically as Newton’s method and the computation of Contractor Iteration Method is cheaper than the Newton’s method.
Abstract: A Decision Support System/Expert System for stock
portfolio selection presented where at first step, both technical and
fundamental data used to estimate technical and fundamental return
and risk (1st phase); Then, the estimated values are aggregated with
the investor preferences (2nd phase) to produce convenient stock
portfolio.
In the 1st phase, there are two expert systems, each of which is
responsible for technical or fundamental estimation. In the technical
expert system, for each stock, twenty seven candidates are identified
and with using rough sets-based clustering method (RC) the effective
variables have been selected. Next, for each stock two fuzzy rulebases
are developed with fuzzy C-Mean method and Takai-Sugeno-
Kang (TSK) approach; one for return estimation and the other for
risk. Thereafter, the parameters of the rule-bases are tuned with backpropagation
method. In parallel, for fundamental expert systems,
fuzzy rule-bases have been identified in the form of “IF-THEN" rules
through brainstorming with the stock market experts and the input
data have been derived from financial statements; as a result two
fuzzy rule-bases have been generated for all the stocks, one for return
and the other for risk.
In the 2nd phase, user preferences represented by four criteria and
are obtained by questionnaire. Using an expert system, four estimated
values of return and risk have been aggregated with the respective
values of user preference. At last, a fuzzy rule base having four rules,
treats these values and produce a ranking score for each stock which
will lead to a satisfactory portfolio for the user.
The stocks of six manufacturing companies and the period of
2003-2006 selected for data gathering.
Abstract: Packing problems arise in a wide variety of application
areas. The basic problem is that of determining an efficient arrangement
of different objects in a region without any overlap and
with minimal wasted gap between shapes. This paper presents a
novel population based approach for optimizing arrangement of irregular
shapes. In this approach, each shape is coded as an agent and
the agents' reproductions and grouping policies results in arrangements
of the objects in positions with least wasted area between
them. The approach is implemented in an application for cutting
sheets and test results on several problems from literature are presented.
Abstract: An accurate procedure to determine free vibrations of
beams and plates is presented.
The natural frequencies are exact solutions of governing vibration
equations witch load to a nonlinear homogeny system.
The bilinear and linear structures considered simulate a bridge.
The dynamic behavior of this one is analyzed by using the theory of
the orthotropic plate simply supported on two sides and free on the
two others. The plate can be excited by a convoy of constant or
harmonic loads. The determination of the dynamic response of the
structures considered requires knowledge of the free frequencies and
the shape modes of vibrations. Our work is in this context. Indeed,
we are interested to develop a self-consistent calculation of the Eigen
frequencies.
The formulation is based on the determination of the solution of
the differential equations of vibrations. The boundary conditions
corresponding to the shape modes permit to lead to a homogeneous
system. Determination of the noncommonplace solutions of this
system led to a nonlinear problem in Eigen frequencies.
We thus, develop a computer code for the determination of the
eigenvalues. It is based on a method of bisection with interpolation
whose precision reaches 10 -12. Moreover, to determine the
corresponding modes, the calculation algorithm that we develop uses
the method of Gauss with a partial optimization of the "pivots"
combined with an inverse power procedure. The Eigen frequencies
of a plate simply supported along two opposite sides while
considering the two other free sides are thus analyzed. The results
could be generalized with the case of a beam by regarding it as a
plate with low width.
We give, in this paper, some examples of treated cases. The
comparison with results presented in the literature is completely
satisfactory.
Abstract: This paper presents a simple and effective method for approximate indexing of instances for instance based learning. The method uses an interval tree to determine a good starting search point for the nearest neighbor. The search stops when an early stopping criterion is met. The method proved to be very effective especially when only the first nearest neighbor is required.