Abstract: Power Factor (PF) is one of the most important parameters in the electrical systems, especially in the water pumping station. The low power factor value of the water pumping stations causes penalty for the electrical bill. There are many methods use for power factor improvement. Each one of them uses a capacitor on the electrical power network. The position of the capacitors is varied depends on many factors such as; voltage level and capacitors rating. Adding capacitors on the motor terminals increase the supply power factor from 0.8 to more than 0.9 but these capacitors cause some problems for the electrical grid network, such as increasing the harmonic contents of the grid line voltage. In this paper the effects of using capacitors in the water pumping stations to improve the power factor value on the harmonic contents of the electrical grid network are studied. One of large water pumping stations in Kafr El-Shikh Governorate in Egypt was used, as a case study. The effect of capacitors on the line voltage harmonic contents is measured. The station uses capacitors to improve the PF values at the 1 lkv grid network. The power supply harmonics values are measured by a power quality analyzer at different loading conditions. The results showed that; the capacitors improved the power factor value of the feeder and its value increased than 0.9. But the THD values are increased by adding these capacitors. The harmonic analysis showed that; the 13th, 17th, and 19th harmonics orders are increased also by adding the capacitors.
Abstract: The work presents a development of EN338 strength classes for Strombosia pustulata, Pterygotama crocarpa, Nauclea diderrichii and Entandrophragma cyclindricum Nigerian timber species. The specimens for experimental measurements were obtained from the timber-shed at the famous Panteka market in Kaduna in the northern part of Nigeria. Laboratory experiments were conducted to determine the physical and mechanical properties of the selected timber species in accordance with EN 13183-1 and ASTM D193. The mechanical properties were determined using three point bending test. The generated properties were used to obtain the characteristic values of the material properties in accordance with EN384. The selected timber species were then classified according to EN 338. Strombosia pustulata, Pterygotama crocarpa, Nauclea diderrichii and Entandrophragma cyclindricum were assigned to strength classes D40, C14, D40 and D24 respectively. Other properties such as tensile and compressive strengths parallel and perpendicular to grains, shear strength as well as shear modulus were obtained in accordance with EN 338.
Abstract: The most influential programming paradigm today
is object oriented (OO) programming and it is widely used in
education and industry. Recognizing the importance of equipping
students with OO knowledge and skills, it is not surprising that most
Computer Science degree programs offer OO-related courses. How
do we assess whether the students have acquired the right objectoriented
skills after they have completed their OO courses? What are
object oriented skills? Currently none of the current assessment
techniques would be able to provide this answer. Traditional forms of
OO programming assessment provide a ways for assigning numerical
scores to determine letter grades. But this rarely reveals information
about how students actually understand OO concept. It appears
reasonable that a better understanding of how to define and assess
OO skills is needed by developing a criterion referenced model. It is
even critical in the context of Malaysia where there is currently a
growing concern over the level of competency of Malaysian IT
graduates in object oriented programming. This paper discussed the
approach used to develop the criterion-referenced assessment model.
The model can serve as a guideline when conducting OO
programming assessment as mentioned. The proposed model is
derived by using Goal Questions Metrics methodology, which helps
formulate the metrics of interest. It concluded with a few suggestions
for further study.
Abstract: With the explosive growth of data available on the
Internet, personalization of this information space become a
necessity. At present time with the rapid increasing popularity of the
WWW, Websites are playing a crucial role to convey knowledge and
information to the end users. Discovering hidden and meaningful
information about Web users usage patterns is critical to determine
effective marketing strategies to optimize the Web server usage for
accommodating future growth. The task of mining useful information
becomes more challenging when the Web traffic volume is enormous
and keeps on growing. In this paper, we propose a intelligent model
to discover and analyze useful knowledge from the available Web
log data.
Abstract: Presence of phytosterol compound in Durian seed
(Durio zibethinus) or known as King of fruits has been discovered
from screening work using reagent test. Further analysis work has
been carried out using mass spectrometer in order to support the
priliminary finding. Isolation and purification of the major
phytosterol has been carried out using an open column
chromatography. The separation was monitored using thin layer
chromatography (TLC). Major isolated compounds and purified
phytosterol were identified using mass spectrometer and nuclear
magnetic resonance (NMR). This novel finding could promote
utilization of durian seeds as a functional ingredient in food products
through production of standardized extract based on phytosterol
content.
Abstract: Intelligent systems are required in order to quickly and accurately analyze enormous quantities of data in the Internet environment. In intelligent systems, information extracting processes can be divided into supervised learning and unsupervised learning. This paper investigates intelligent clustering by unsupervised learning. Intelligent clustering is the clustering system which determines the clustering model for data analysis and evaluates results by itself. This system can make a clustering model more rapidly, objectively and accurately than an analyzer. The methodology for the automatic clustering intelligent system is a multi-agent system that comprises a clustering agent and a cluster performance evaluation agent. An agent exchanges information about clusters with another agent and the system determines the optimal cluster number through this information. Experiments using data sets in the UCI Machine Repository are performed in order to prove the validity of the system.
Abstract: A modified Genetic Algorithm (GA) based optimal selection of parameters for Automatic Generation Control (AGC) of multi-area electric energy systems is proposed in this paper. Simulations on multi-area reheat thermal system with and without consideration of nonlinearity like governor dead band followed by 1% step load perturbation is performed to exemplify the optimum parameter search. In this proposed method, a modified Genetic Algorithm is proposed where one point crossover with modification is employed. Positional dependency in respect of crossing site helps to maintain diversity of search point as well as exploitation of already known optimum value. This makes a trade-off between exploration and exploitation of search space to find global optimum in less number of generations. The proposed GA along with decomposition technique as developed has been used to obtain the optimum megawatt frequency control of multi-area electric energy systems. Time-domain simulations are conducted with trapezoidal integration along with decomposition technique. The superiority of the proposed method over existing one is verified from simulations and comparisons.
Abstract: Segmentation of Magnetic Resonance Imaging (MRI) images is the most challenging problems in medical imaging. This paper compares the performances of Seed-Based Region Growing (SBRG), Adaptive Network-Based Fuzzy Inference System (ANFIS) and Fuzzy c-Means (FCM) in brain abnormalities segmentation. Controlled experimental data is used, which designed in such a way that prior knowledge of the size of the abnormalities are known. This is done by cutting various sizes of abnormalities and pasting it onto normal brain tissues. The normal tissues or the background are divided into three different categories. The segmentation is done with fifty seven data of each category. The knowledge of the size of the abnormalities by the number of pixels are then compared with segmentation results of three techniques proposed. It was proven that the ANFIS returns the best segmentation performances in light abnormalities, whereas the SBRG on the other hand performed well in dark abnormalities segmentation.
Abstract: The main purpose of this research aimed to create tactile texture designed media for the blind used for extra learning outside classrooms in order to enhance imagination of the blind about Himmapan creatures, furthermore, the main objective of the research focused on improving the visual disabled perception to be equal to normal people. The target group of the research is blinded students studying in The Bangkok school for the blind between grade 4-6 in the second semester of 2011 who are able to read the braille language. The research methodology consisted of the field study and the documentary study related to the blind, tactile texture designed media and Himmapan creatures. 10 pictures of tactile texture designed media were created in the designing process which began after the analysis had conducted based the primary and secondary data. The works had presented to experts in the visual disabled field who evaluated the works. After approval, the works used as prototype to teach the blind. KeywordsBlind, Himmapan Creatures, Tactile Texture.
Abstract: In this paper a new cost function for blind equalization
is proposed. The proposed cost function, referred to as the modified
maximum normalized cumulant criterion (MMNC), is an extension
of the previously proposed maximum normalized cumulant criterion
(MNC). While the MNC requires a separate phase recovery system
after blind equalization, the MMNC performs joint blind equalization
and phase recovery. To achieve this, the proposed algorithm
maximizes a cost function that considers both amplitude and phase of
the equalizer output. The simulation results show that the proposed
algorithm has an improved channel equalization effect than the MNC
algorithm and simultaneously can correct the phase error that the
MNC algorithm is unable to do. The simulation results also show that
the MMNC algorithm has lower complexity than the MNC algorithm.
Moreover, the MMNC algorithm outperforms the MNC algorithm
particularly when the symbols block size is small.
Abstract: The effect of nano Co3O4 addition on the
superconducting properties of (Bi, Pb)-2223 system was studied. The
samples were prepared by the acetate coprecipitation method. The
Co3O4 with different sizes (10-30 nm and 30-50 nm) from x=0.00 to
0.05 was added to Bi1.6Pb0.4Sr2Ca2Cu3Oy(Co3O4)x. Phase analysis by
XRD method, microstructural examination by SEM and dc electrical
resistivity by four point probe method were done to characterize the
samples. The X-ray diffraction patterns of all the samples indicated
the majority Bi-2223 phase along with minor Bi-2212 and Bi-2201
phases. The volume fraction was estimated from the intensities of Bi-
2223, Bi-2212 and Bi-2201 phase. The sample with x=0.01 wt% of
the added Co3O4 (10-30 nm size) showed the highest volume fraction
of Bi-2223 phase (72%) and the highest superconducting transition
temperature, Tc (~102 K). The non-added sample showed the highest
Tc(~103 K) compared to added samples with nano Co3O4 (30-50 nm
size) added samples. Both the onset critical temperature Tc(onset)
and zero electrical resistivity temperature Tc(R=0) were in the range
of 103-115 ±1K and 91-103 ±1K respectively for samples with added
Co3O4 (10-30 nm and 30-50 nm).
Abstract: Medical compression bandages are widely used in the
treatment of chronic venous disorder. In order to design effective
compression bandages, researchers have attempted to describe the
interface pressure applied by multi-layer bandages using mathematical
models. This paper reports on the work carried out to
compare and validate the mathematical models used to describe the
interface pressure applied by multi-layer bandages. Both analytical
and experimental results showed that using simple multiplication
of a number of bandage layers with the pressure applied by one
layer of bandage or ignoring the increase in the limb radius due to
former layers of bandage will result in overestimating the pressure.
Experimental results showed that the mathematical models, which
take into consideration the increase in the limb radius due to former
bandage layers, are more accurate than the one which does not.
Abstract: For scores of years now, several microfinance
organizations, non governmental organizations and other welfare
organizations have, with a view to aiding the progress of
communities rooted in poverty have been focusing on creating
microentrepreneurs, besides taking several other measures. In recent
times, business corporations have joined forces to combat poverty by
taking up microenterprise development. Hindustan Unilever Limited
(HUL), the Indian subsidiary of Unilever Limited exemplifies this
through its Project Shakti. The company through the Project creates
rural women entrepreneurs by making them direct to home sales
distributors of its products in villages that have thus far been ignored
by multinational corporations. The members participating in Project
Shakti are largely self help group members. The paper focuses on
assessing the impact made by the company on the members engaged
in Project Shakti. The analysis involves use of quantitative methods
to study the effect of Project Shakti on those self help group
members engaged in Project Shakti and those not engaged with
Project Shakti. Path analysis has been used to study the impact made
on those members engaged in Project Shakti. Significant differences
were observed on fronts of entrepreneurial development, economic
empowerment and social empowerment between members associated
with Project Shakti and those not associated with Project Shakti.
Path analysis demonstrated that involvement in Project Shakti led to
entrepreneurial development resulting in economic empowerment
that in turn led to social empowerment and that these three elements
independently induced a feeling of privilege in the women for being
associated with the Project.
Abstract: Signature represents an individual characteristic of a
person which can be used for his / her validation. For such application
proper modeling is essential. Here we propose an offline signature
recognition and verification scheme which is based on extraction of
several features including one hybrid set from the input signature
and compare them with the already trained forms. Feature points
are classified using statistical parameters like mean and variance.
The scanned signature is normalized in slant using a very simple
algorithm with an intention to make the system robust which is
found to be very helpful. The slant correction is further aided by the
use of an Artificial Neural Network (ANN). The suggested scheme
discriminates between originals and forged signatures from simple
and random forgeries. The primary objective is to reduce the two
crucial parameters-False Acceptance Rate (FAR) and False Rejection
Rate (FRR) with lesser training time with an intension to make the
system dynamic using a cluster of ANNs forming a multiple classifier
system.
Abstract: the elastic scattering of protons, deuterons and 3He on 6Li at different incident energies have been analyzed in the framework of the optical model using ECIS88 as well as SPI GENOA codes. The potential parameters were extracted in the phenomenological treatment of measured by us angular distributions and literature data. A good agreement between theoretical and experimental differential cross sections was obtained in whole angular range. Parameters for real part of potential have been also calculated microscopically with singleand double-folding model for the p and d, 3He scattering, respectively, using DFPOT code. For best agreement with experiment the normalization factor N for the potential depth is obtained in the range of 0.7-0.9.
Abstract: Segmentation of a color image composed of different
kinds of regions can be a hard problem, namely to compute for an
exact texture fields. The decision of the optimum number of
segmentation areas in an image when it contains similar and/or un
stationary texture fields. A novel neighborhood-based segmentation
approach is proposed. A genetic algorithm is used in the proposed
segment-pass optimization process. In this pass, an energy function,
which is defined based on Markov Random Fields, is minimized. In
this paper we use an adaptive threshold estimation method for image
thresholding in the wavelet domain based on the generalized
Gaussian distribution (GGD) modeling of sub band coefficients. This
method called Normal Shrink is computationally more efficient and
adaptive because the parameters required for estimating the threshold
depend on sub band data energy that used in the pre-stage of
segmentation. A quad tree is employed to implement the multi
resolution framework, which enables the use of different strategies at
different resolution levels, and hence, the computation can be
accelerated. The experimental results using the proposed
segmentation approach are very encouraging.
Abstract: Extensive research has been devoted to economic
production quantity (EPQ) problem. However, no attention has been
paid to problems where production period length is constrained. In
this paper, we address the problem of deciding the optimal
production quantity and the number of minor setups within each
cycle, in which, production period length is constrained but a minor
setup is possible for pass the constraint. A mathematical model is
developed and Iterated Local Search (ILS) is proposed to solve this
problem. Finally, solution procedure illustrated with a numerical
example and results are analyzed.
Abstract: This paper addresses the problem of recognizing and
interpreting the behavior of human workers in industrial
environments for the purpose of integrating humans in software
controlled manufacturing environments. In this work we propose a
generic concept in order to derive solutions for task-related manual
production applications. Thus, we are able to use a versatile concept
providing flexible components and being less restricted to a specific
problem or application. We instantiate our concept in a spot welding
scenario in which the behavior of a human worker is interpreted
when performing a welding task with a hand welding gun. We
acquire signals from inertial sensors, video cameras and triggers and
recognize atomic actions by using pose data from a marker based
video tracking system and movement data from inertial sensors.
Recognized atomic actions are analyzed on a higher evaluation level
by a finite state machine.
Abstract: The objective of this paper is to develop a neural
network-based residual generator to detect the fault in the actuators
for a specific communication satellite in its attitude control system
(ACS). First, a dynamic multilayer perceptron network with dynamic
neurons is used, those neurons correspond a second order linear
Infinite Impulse Response (IIR) filter and a nonlinear activation
function with adjustable parameters. Second, the parameters from the
network are adjusted to minimize a performance index specified by
the output estimated error, with the given input-output data collected
from the specific ACS. Then, the proposed dynamic neural network
is trained and applied for detecting the faults injected to the wheel,
which is the main actuator in the normal mode for the communication
satellite. Then the performance and capabilities of the proposed
network were tested and compared with a conventional model-based
observer residual, showing the differences between these two
methods, and indicating the benefit of the proposed algorithm to
know the real status of the momentum wheel. Finally, the application
of the methods in a satellite ground station is discussed.
Abstract: Fiber optic sensor technology offers the possibility of
sensing different parameters like strain, temperature, pressure in
harsh environment and remote locations. these kinds of sensors
modulates some features of the light wave in an optical fiber such an
intensity and phase or use optical fiber as a medium for transmitting
the measurement information.
The advantages of fiber optic sensors in contrast to conventional
electrical ones make them popular in different applications and now a
day they consider as a key component in improving industrial
processes, quality control systems, medical diagnostics, and
preventing and controlling general process abnormalities.
This paper is an introduction to fiber optic sensor technology and
some of the applications that make this branch of optic technology,
which is still in its early infancy, an interesting field.