Abstract: A large number of chemical, bio-chemical and pollution-control processes use heterogeneous fixed-bed reactors. The use of finite hollow cylindrical catalyst pellets can enhance conversion levels in such reactors. The absence of the pellet core can significantly lower the diffusional resistance associated with the solid phase. This leads to a better utilization of the catalytic material, which is reflected in the higher values for the effectiveness factor, leading ultimately to an enhanced conversion level in the reactor. It is however important to develop a rigorous heterogeneous model for the reactor incorporating the two-dimensional feature of the solid phase owing to the presence of the finite hollow cylindrical catalyst pellet. Presently, heterogeneous models reported in the literature invariably employ one-dimension solid phase models meant for spherical catalyst pellets. The objective of the paper is to present a rigorous model of the fixed-bed reactors containing finite hollow cylindrical catalyst pellets. The reaction kinetics considered here is the widely used Michaelis–Menten kinetics for the liquid-phase bio-chemical reactions. The reaction parameters used here are for the enzymatic degradation of urea. Results indicate that increasing the height to diameter ratio helps to improve the conversion level. On the other hand, decreasing the thickness is apparently not as effective. This could however be explained in terms of the higher void fraction of the bed that causes a smaller amount of the solid phase to be packed in the fixed-bed bio-chemical reactor.
Abstract: Nowadays it is a trend for electronic circuit designers to
integrate all system components on a single-chip. This paper proposed
the design of a single-chip proportional to absolute temperature
(PTAT) sensor including a voltage reference circuit using CEDEC
0.18m CMOS Technology. It is a challenge to design asingle-chip
wide range linear response temperature sensor for many applications.
The channel widths between the compensation transistor and the
reference transistor are critical to design the PTAT temperature sensor
circuit. The designed temperature sensor shows excellent linearity
between -100°C to 200° and the sensitivity is about 0.05mV/°C.
The chip is designed to operate with a single voltage source of 1.6V.
Abstract: The trial in the city, located 170 kilometers from the
Iranian city of Ahvaz was Omidiyeh. The main factor in this project
includes 4 levels in control (without hormones), use of hormones in
the seed, vegetative and flowering stage respectively. And sub-plots
included 3 varieties of vetch in three levels, with local names, was the
jewel in the study of light and Auxin in the vegetative and
reproductive different times in different varieties of vetch was
investigated. This test has been taken in the plots in a randomized
complete block with four replications. In order to study the effects of
the hormone Auxin in the growth stages (seed, vegetative and
flowering) to control (no hormone Auxin) on three local varieties of
vetch, the essence of light and plant height, number of pods per plant,
seed number The pods, seeds per plant, grain weight, grain yield,
plant dry weight and protein content were measured. Among the
vetch varieties for plant height, number of pods per plant, a seed per
plant, grain weight, grain yield, and plant dry weight and protein
levels of 1 percent of plant and seed number per pod per plant at 5%
level of There was no significant difference. Interactions for grain
yield per plant, grain yield and protein levels of 1 percent and the
number of seeds per pod and seed weight are significant differences
in levels 5 and plant height and plant dry weight of the interaction
were INFLUENCE There was no significant difference in them.
Abstract: We propose the use of magneto-optic Kerr effect (MOKE) to realize single-qubit quantum gates. We consider longitudinal and polar MOKE in reflection geometry in which the magnetic field is parallel to both the plane of incidence and surface of the film. MOKE couples incident TE and TM polarized photons and the Hamiltonian that represents this interaction is isomorphic to that of a canonical two-level quantum system. By varying the phase and amplitude of the magnetic field, we can realize Hadamard, NOT, and arbitrary phase-shift single-qubit quantum gates. The principal advantage is operation with magnetically non-transparent materials.
Abstract: IVE toolkit has been created for facilitating research,education and development in the field of virtual storytelling and computer games. Primarily, the toolkit is intended for modelling action selection mechanisms of virtual humans, investigating level-of-detail AI techniques for large virtual environments, and for exploring joint behaviour and role-passing technique (Sec. V). Additionally, the toolkit can be used as an AI middleware without any changes. The main facility of IVE is that it serves for prototyping both the AI and virtual worlds themselves. The purpose of this paper is to describe IVE's features in general and to present our current work - including an educational game - on this platform.
Abstract: Vehicle suspension design must fulfill
some conflicting criteria. Among those is ride comfort
which is attained by minimizing the acceleration
transmitted to the sprung mass, via suspension spring
and damper. Also good handling of a vehicle is a
desirable property which requires stiff suspension and
therefore is in contrast with a vehicle with good ride.
Among the other desirable features of a suspension is
the minimization of the maximum travel of suspension.
This travel which is called suspension working space in
vehicle dynamics literature is also a design constraint
and it favors good ride. In this research a full car 8
degrees of freedom model has been developed and the
three above mentioned criteria, namely: ride, handling
and working space has been adopted as objective
functions. The Multi Objective Programming (MOP)
discipline has been used to find the Pareto Front and
some reasoning used to chose a design point between
these non dominated points of Pareto Front.
Abstract: The traditional Failure Mode and Effects Analysis
(FMEA) uses Risk Priority Number (RPN) to evaluate the risk level
of a component or process. The RPN index is determined by
calculating the product of severity, occurrence and detection indexes.
The most critically debated disadvantage of this approach is that
various sets of these three indexes may produce an identical value of
RPN. This research paper seeks to address the drawbacks in
traditional FMEA and to propose a new approach to overcome these
shortcomings. The Risk Priority Code (RPC) is used to prioritize
failure modes, when two or more failure modes have the same RPN.
A new method is proposed to prioritize failure modes, when there is a
disagreement in ranking scale for severity, occurrence and detection.
An Analysis of Variance (ANOVA) is used to compare means of
RPN values. SPSS (Statistical Package for the Social Sciences)
statistical analysis package is used to analyze the data. The results
presented are based on two case studies. It is found that the proposed
new methodology/approach resolves the limitations of traditional
FMEA approach.
Abstract: This study presents a systematic analysis of the
dynamic behaviors of a gear-bearing system with porous squeeze film
damper (PSFD) under nonlinear suspension, nonlinear oil-film force
and nonlinear gear meshing force effect. It can be found that the
system exhibits very rich forms of sub-harmonic and even the chaotic
vibrations. The bifurcation diagrams also reveal that greater values of
permeability may not only improve non-periodic motions effectively,
but also suppress dynamic amplitudes of the system. Therefore, porous
effect plays an important role to improve dynamic stability of
gear-bearing systems or other mechanical systems. The results
presented in this study provide some useful insights into the design
and development of a gear-bearing system for rotating machinery that
operates in highly rotational speed and highly nonlinear regimes.
Abstract: The chemical degradation of dieldrin in ferric
sulfide and iron powder aqueous suspension was investigated
in laboratory batch type experiments. To identify the reaction
mechanism, reduced copper was used as reductant. More than
90% of dieldrin was degraded using both reaction systems after
29 days. Initial degradation rate of the pesticide using ferric
sulfide was superior to that using iron powder. The reaction
schemes were completely dissimilar even though the ferric ion
plays an important role in both reaction systems. In the case of
metallic iron powder, dieldrin undergoes partial dechlorination.
This reaction proceeded by reductive hydrodechlorination with
the generation of H+, which arise by oxidation of ferric iron.
This reductive reaction was accelerated by reductant but
mono-dechlorination intermediates were accumulated. On the
other hand, oxidative degradation was observed in the reaction
with ferric sulfide, and the stable chemical structure of dieldrin
was decomposed into water-soluble intermediates. These
reaction intermediates have no chemical structure of drin class.
This dehalogenation reaction assumes to occur via the adsorbed
hydroxyl radial generated on the surface of ferric sulfide.
Abstract: Resins are used in nuclear power plants for water
ultrapurification. Two approaches are considered in this work:
column experiments and simulations. A software called OPTIPUR
was developed, tested and used. The approach simulates the onedimensional
reactive transport in porous medium with convectivedispersive
transport between particles and diffusive transport within
the boundary layer around the particles. The transfer limitation in the
boundary layer is characterized by the mass transfer coefficient
(MTC). The influences on MTC were measured experimentally. The
variation of the inlet concentration does not influence the MTC; on
the contrary of the Darcy velocity which influences. This is consistent
with results obtained using the correlation of Dwivedi&Upadhyay.
With the MTC, knowing the number of exchange site and the relative
affinity, OPTIPUR can simulate the column outlet concentration
versus time. Then, the duration of use of resins can be predicted in
conditions of a binary exchange.
Abstract: In this paper, an estimation accuracy of multiple moving
talker tracking using a microphone array is improved. The tracking
can be achieved by the adaptive method in which two algorithms are integrated, namely, the PAST (Projection Approximation Subspace
Tracking) algorithm and the IPLS (Interior Point Least Square) algorithm. When either talker begins to speak again after a silent
period, an appropriate feasible region for an evaluation function of
the IPLS algorithm might not be set. Then, the tracking fails due to the incorrect updating. Therefore, if an increment of the number of
active talkers is detected, the feasible region must be reset. Then, a low cost realization is required for the high speed tracking and a high
accuracy realization is desired for the precise tracking. In this paper,
the directions roughly estimated using the delayed-sum-array method
are used for the resetting. Several results of experiments performed in
an actual room environment show the effectiveness of the proposed method.
Abstract: Historical monuments as architectural heritage are,
economically and culturally, considered one of the key aspects for
modern communities. Cultural heritage represents a country-s
national identity and pride and maintains and enriches that country-s
culture. Therefore, conservation of the monuments remained from
our ancestors requires everybody-s serious and unremitting effort.
Conservation, renewal, restoration, and technical study of cultural
and historical matters are issues which have a special status among
various forms of art and science in the present century and this is due
to two reasons: firstly, progress of humankind in this century has
created a factor called environmental pollution which not only has
caused new destructive processes of cultural/historical monuments
but also has accelerated the previous destructive processes by several
times, and secondly, the rapid advance of various sciences, especially
chemistry, has lead to the contribution of new methods and materials
to this significant issue.
Abstract: In this paper, we present a preconditioned AOR-type iterative method for solving the linear systems Ax = b, where A is a Z-matrix. And give some comparison theorems to show that the rate of convergence of the preconditioned AOR-type iterative method is faster than the rate of convergence of the AOR-type iterative method.
Abstract: This paper deals optimized model to investigate the
effects of peak current, pulse on time and pulse off time in EDM performance on material removal rate of titanium alloy utilizing copper tungsten as electrode and positive polarity of the electrode. The experiments are carried out on Ti6Al4V. Experiments were
conducted by varying the peak current, pulse on time and pulse off time. A mathematical model is developed to correlate the influences of these variables and material removal rate of workpiece. Design of
experiments (DOE) method and response surface methodology
(RSM) techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through
analysis of variance (ANOVA). The obtained results evidence that as
the material removal rate increases as peak current and pulse on time
increases. The effect of pulse off time on MRR changes with peak ampere. The optimum machining conditions in favor of material removal rate are verified and compared. The optimum machining
conditions in favor of material removal rate are estimated and verified with proposed optimized results. It is observed that the developed model is within the limits of the agreeable error (about
4%) when compared to experimental results. This result leads to desirable material removal rate and economical industrial machining to optimize the input parameters.
Abstract: The study of the geometric shape of the plunging wave enclosed vortices as a possible indicator for the breaking intensity of ocean waves has been ongoing for almost 50 years with limited success. This paper investigates the validity of using the vortex ratio and vortex angle as methods of predicting breaking intensity. Previously published works on vortex parameters, based on regular wave flume results or solitary wave theory, present contradictory results and conclusions. Through the first complete analysis of field collected irregular wave breaking vortex parameters it is illustrated that the vortex ratio and vortex angle cannot be accurately predicted using standard breaking wave characteristics and hence are not suggested as a possible indicator for breaking intensity.
Abstract: Traditionally, terror groups have been formed by ideologically aligned actors who perceive a lack of options for achieving political or social change. However, terrorist attacks have been increasingly carried out by small groups of actors or lone individuals who may be only ideologically affiliated with larger, formal terrorist organizations. The formation of these groups represents the inverse of traditional organizational growth, whereby structural de-evolution within issue-based organizations leads to the formation of small, independent terror cells. Ideological franchising – the bypassing of formal affiliation to the “parent" organization – represents the de-evolution of traditional concepts of organizational structure in favor of an organic, independent, and focused unit. Traditional definitions of dark networks that are issue-based include focus on an identified goal, commitment to achieving this goal through unrestrained actions, and selection of symbolic targets. The next step in the de-evolution of small dark networks is the miniorganization, consisting of only a handful of actors working toward a common, violent goal. Information-sharing through social media platforms, coupled with civil liberties of democratic nations, provide the communication systems, access to information, and freedom of movement necessary for small dark networks to flourish without the aid of a parent organization. As attacks such as the 7/7 bombings demonstrate the effectiveness of small dark networks, terrorist actors will feel increasingly comfortable aligning with an ideology only, without formally organizing. The natural result of this de-evolving organization is the single actor event, where an individual seems to subscribe to a larger organization-s violent ideology with little or no formal ties.
Abstract: Software reliability prediction gives a great opportunity to measure the software failure rate at any point throughout system test. A software reliability prediction model provides with the technique for improving reliability. Software reliability is very important factor for estimating overall system reliability, which depends on the individual component reliabilities. It differs from hardware reliability in that it reflects the design perfection. Main reason of software reliability problems is high complexity of software. Various approaches can be used to improve the reliability of software. We focus on software reliability model in this article, assuming that there is a time redundancy, the value of which (the number of repeated transmission of basic blocks) can be an optimization parameter. We consider given mathematical model in the assumption that in the system may occur not only irreversible failures, but also a failure that can be taken as self-repairing failures that significantly affect the reliability and accuracy of information transfer. Main task of the given paper is to find a time distribution function (DF) of instructions sequence transmission, which consists of random number of basic blocks. We consider the system software unreliable; the time between adjacent failures has exponential distribution.
Abstract: The world economic crises and budget constraints
have caused authorities, especially those in developing countries, to
rationalize water quality monitoring activities. Rationalization
consists of reducing the number of monitoring sites, the number of
samples, and/or the number of water quality variables measured. The
reduction in water quality variables is usually based on correlation. If
two variables exhibit high correlation, it is an indication that some of
the information produced may be redundant. Consequently, one
variable can be discontinued, and the other continues to be measured.
Later, the ordinary least squares (OLS) regression technique is
employed to reconstitute information about discontinued variable by
using the continuously measured one as an explanatory variable. In
this paper, two record extension techniques are employed to
reconstitute information about discontinued water quality variables,
the OLS and the Line of Organic Correlation (LOC). An empirical
experiment is conducted using water quality records from the Nile
Delta water quality monitoring network in Egypt. The record
extension techniques are compared for their ability to predict
different statistical parameters of the discontinued variables. Results
show that the OLS is better at estimating individual water quality
records. However, results indicate an underestimation of the variance
in the extended records. The LOC technique is superior in preserving
characteristics of the entire distribution and avoids underestimation
of the variance. It is concluded from this study that the OLS can be
used for the substitution of missing values, while LOC is preferable
for inferring statements about the probability distribution.
Abstract: Complex networks have been intensively studied across
many fields, especially in Internet technology, biological engineering,
and nonlinear science. Software is built up out of many interacting
components at various levels of granularity, such as functions, classes,
and packages, representing another important class of complex networks.
It can also be studied using complex network theory. Over the
last decade, many papers on the interdisciplinary research between
software engineering and complex networks have been published.
It provides a different dimension to our understanding of software
and also is very useful for the design and development of software
systems. This paper will explore how to use the complex network
theory to analyze software structure, and briefly review the main
advances in corresponding aspects.
Abstract: Existing literature ondesign reasoning seems to give
either one sided accounts on expert design behaviour based on
internal processing. In the same way ecological theoriesseem to
focus one sidedly on external elementsthat result in a lack of unifying
design cognition theory. Although current extended design cognition
studies acknowledge the intellectual interaction between internal and
external resources, there still seems to be insufficient understanding
of the complexities involved in such interactive processes. As
such,this paper proposes a novelmulti-directional model for design
researchers tomap the complex and dynamic conduct controlling
behaviour in which both the computational and ecological
perspectives are integrated in a vertical manner. A clear distinction
between identified intentional and emerging physical drivers, and
relationships between them during the early phases of experts- design
process, is demonstrated by presenting a case study in which the
model was employed.