Abstract: Gas turbine air inlet cooling is a useful method for
increasing output for regions where significant power demand and
highest electricity prices occur during the warm months. Inlet air
cooling increases the power output by taking advantage of the gas
turbine-s feature of higher mass flow rate when the compressor inlet
temperature decreases. Different methods are available for reducing
gas turbine inlet temperature. There are two basic systems currently
available for inlet cooling. The first and most cost-effective system is
evaporative cooling. Evaporative coolers make use of the evaporation
of water to reduce the gas turbine-s inlet air temperature. The second
system employs various ways to chill the inlet air. In this method, the
cooling medium flows through a heat exchanger located in the inlet
duct to remove heat from the inlet air. However, the evaporative
cooling is limited by wet-bulb temperature while the chilling can cool
the inlet air to temperatures that are lower than the wet bulb
temperature. In the present work, a thermodynamic model of a gas
turbine is built to calculate heat rate, power output and thermal
efficiency at different inlet air temperature conditions. Computational
results are compared with ISO conditions herein called "base-case".
Therefore, the two cooling methods are implemented and solved for
different inlet conditions (inlet temperature and relative humidity).
Evaporative cooler and absorption chiller systems results show that
when the ambient temperature is extremely high with low relative
humidity (requiring a large temperature reduction) the chiller is the
more suitable cooling solution. The net increment in the power output
as a function of the temperature decrease for each cooling method is
also obtained.
Abstract: Palm shell obtained from coastal part of southern
India was studied for the removal for the adsorption of Hg (II) ions.
Batch adsorption experiments were carried out as a function of pH,
concentration of Hg (II) ions, time, temperature and adsorbent dose.
Maximum removal was seen in the range pH 4.0- pH 7.0. The palm
shell powder used as adsorbent was characterized for its surface area,
SEM, PXRD, FTIR, ion exchange capacity, moisture content, and
bulk density, soluble content in water and acid and pH. The
experimental results were analyzed using Langmuir I, II, III, IV and
Freundlich adsorption isotherms. The batch sorption kinetics was
studied for the first order reversible reaction, pseudo first order;
pseudo second order reaction and the intra-particle diffusion reaction.
The biomass was successfully used for removal Hg (II) from
synthetic and industrial effluents and the technique appears
industrially applicable and viable.
Abstract: Natural disasters, including earthquake, kill many people around the world every year. Society rescue actions, which start after the earthquake and are called LAST in abbreviation, include locating, access, stabilization and transportation. In the present article, we have studied the process of local accessibility to the injured and transporting them to health care centers. With regard the heavy traffic load due to earthquake, the destruction of connecting roads and bridges and the heavy debris in alleys and street, which put the lives of the injured and the people buried under the debris in danger, accelerating the rescue actions and facilitating the accessibilities are of great importance, obviously. Tehran, the capital of Iran, is among the crowded cities in the world and is the center of extensive economic, political, cultural and social activities. Tehran has a population of about 9.5 millions and because of the immigration of people from the surrounding cities. Furthermore, considering the fact that Tehran is located on two important and large faults, a 6 Richter magnitude earthquake in this city could lead to the greatest catastrophe during the entire human history. The present study is a kind of review and a major part of the required information for it, has been obtained from libraries all of the rescue vehicles around the world, including rescue helicopters, ambulances, fire fighting vehicles and rescue boats, and their applied technology, and also the robots specifically designed for the rescue system and the advantages and disadvantages of them, have been investigated. The studies show that there is a significant relationship between the rescue team-s arrival time at the incident zone and the number of saved people; so that, if the duration of burial under debris 30 minutes, the probability of survival is %99.3, after a day is %81, after 2days is %19 and after 5days is %7.4. The exiting transport systems all have some defects. If these defects are removed, more people could be saved each hour and the preparedness against natural disasters is increased. In this study, transport system has been designed for the rescue team and the injured; which could carry the rescue team to the incident zone and the injured to the health care centers. In addition, this system is able to fly in the air and move on the earth as well; so that the destruction of roads and the heavy traffic load could not prevent the rescue team from arriving early at the incident zone. The system also has the equipment required firebird for debris removing, optimum transport of the injured and first aid.
Abstract: This paper presents a novel algorithm of stereo
correspondence with rank transform. In this algorithm we used the
genetic algorithm to achieve the accurate disparity map. Genetic
algorithms are efficient search methods based on principles of
population genetic, i.e. mating, chromosome crossover, gene
mutation, and natural selection. Finally morphology is employed to
remove the errors and discontinuities.
Abstract: Data mining uses a variety of techniques each of which is useful for some particular task. It is important to have a deep understanding of each technique and be able to perform sophisticated analysis. In this article we describe a tool built to simulate a variation of the Kohonen network to perform unsupervised clustering and support the entire data mining process up to results visualization. A graphical representation helps the user to find out a strategy to optmize classification by adding, moving or delete a neuron in order to change the number of classes. The tool is also able to automatically suggest a strategy for number of classes optimization.The tool is used to classify macroeconomic data that report the most developed countries? import and export. It is possible to classify the countries based on their economic behaviour and use an ad hoc tool to characterize the commercial behaviour of a country in a selected class from the analysis of positive and negative features that contribute to classes formation.
Abstract: A simple mobile engine-driven pneumatic paddy
collector made of locally available materials using local
manufacturing technology was designed, fabricated, and tested for
collecting and bagging of paddy dried on concrete pavement. The
pneumatic paddy collector had the following major components:
radial flat bladed type centrifugal fan, power transmission system,
bagging area, frame and the conveyance system. Results showed
significant differences on the collecting capacity, noise level, and fuel
consumption when rotational speed of the air mover shaft was varied.
Other parameters such as collecting efficiency, air velocity,
augmented cracked grain percentage, and germination rate were not
significantly affected by varying rotational speed of the air mover
shaft. The pneumatic paddy collector had a collecting efficiency of
99.33 % with a collecting capacity of 2685.00 kg/h at maximum
rotational speed of centrifugal fan shaft of about 4200 rpm. The
machine entailed an investment cost of P 62,829.25. The break-even
weight of paddy was 510,606.75 kg/yr at a collecting cost of 0.11
P/kg of paddy. Utilizing the machine for 400 hours per year
generated an income of P 23,887.73. The projected time needed to
recover cost of the machine based on 2685 kg/h collecting capacity
was 2.63 year.
Abstract: IETF defines mobility support in IPv6, i.e. MIPv6, to
allow nodes to remain reachable while moving around in the IPv6
internet. When a node moves and visits a foreign network, it is still
reachable through the indirect packet forwarding from its home
network. This triangular routing feature provides node mobility but
increases the communication latency between nodes. This deficiency
can be overcome by using a Binding Update (BU) scheme, which let
nodes keep up-to-date IP addresses and communicate with each other
through direct IP routing. To further protect the security of BU, a
Return Routability (RR) procedure was developed. However, it has
been found that RR procedure is vulnerable to many attacks. In this
paper, we will propose a lightweight RR procedure based on
geometric computing. In consideration of the inherent limitation of
computing resources in mobile node, the proposed scheme is
developed to minimize the cost of computations and to eliminate the
overhead of state maintenance during binding updates. Compared with
other CGA-based BU schemes, our scheme is more efficient and
doesn-t need nonce tables in nodes.
Abstract: In this paper the behavior of fixed series compensated
extra high voltage transmission lines during faults is simulated. Many
over-voltage protection schemes for series capacitors are limited in
terms of size and performance, and are easily affected by
environmental conditions. While the need for more compact and
environmentally robust equipment is required. use of series
capacitors for compensating part of the inductive reactance of long
transmission lines increases the power transmission capacity.
Emphasis is given on the impact of modern capacitor protection
techniques (MOV protection). The simulation study is performed
using MATLAB/SIMULINK®and results are given for a three phase
and a single phase to ground fault.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: Electromyography (EMG) signal processing has been investigated remarkably regarding various applications such as in rehabilitation systems. Specifically, wavelet transform has served as a powerful technique to scrutinize EMG signals since wavelet transform is consistent with the nature of EMG as a non-stationary signal. In this paper, the efficiency of wavelet transform in surface EMG feature extraction is investigated from four levels of wavelet decomposition and a comparative study between different mother wavelets had been done. To recognize the best function and level of wavelet analysis, two evaluation criteria, scatter plot and RES index are recruited. Hereupon, four wavelet families, namely, Daubechies, Coiflets, Symlets and Biorthogonal are studied in wavelet decomposition stage. Consequently, the results show that only features from first and second level of wavelet decomposition yields good performance and some functions of various wavelet families can lead to an improvement in separability class of different hand movements.
Abstract: There are many debates now regarding undervalued
and overvalued currencies currently traded on the world financial
market. This paper contributes to these debates from a theoretical
point of view. We present the three most commonly used methods of
estimating the equilibrium real effective exchange rate (REER):
macroeconomic balance approach, external sustainability approach
and equilibrium real effective exchange rate approach in the reduced
form. Moreover, we discuss key concepts of the calculation of the
real exchange rate (RER) based on applied explanatory variables:
nominal exchange rates, terms of trade and tradable and non-tradable
goods. Last but not least, we discuss the three main driving forces
behind real exchange rates movements which include terms of trade,
relative productivity growth and the interest rate differential.
Abstract: The presented article deals with the description of a
numerical model of a corridor at a Central Interim Spent Fuel Storage
Facility (hereinafter CISFSF). The model takes into account the
effect of air flows on the temperature of stored waste. The
computational model was implemented in the ANSYS/CFX
programming environment in the form of a CFD task solution, which
was compared with an approximate analytical calculation. The article
includes a categorization of the individual alternatives for the
ventilation of such underground systems. The aim was to evaluate a
ventilation system for a CISFSF with regard to its stability and
capacity to provide sufficient ventilation for the removal of heat
produced by stored casks with spent nuclear fuel.
Abstract: The purpose of this paper is to elucidate the flow unsteady behavior for moving plug in convergent-divergent variable thrust nozzle. Compressible axisymmetric Navier-Stokes equations are used to study this physical phenomenon. Different velocities are set for plug to investigate the effect of plug movement on flow unsteadiness. Variation of mass flow rate and thrust are compared under two conditions: First, the plug is placed at different positions and flow is simulated to reach the steady state (quasi steady simulation) and second, the plug is moved with assigned velocity and flow simulation is coupled with plug movement (unsteady simulation). If plug speed is high enough and its movement time scale is at the same order of the flow time scale, variation of the mass flow rate and thrust level versus plug position demonstrate a vital discrepancy under the quasi steady and unsteady conditions. This phenomenon should be considered especially from response time viewpoints in thrusters design.
Abstract: The city of Melbourne in Victoria, Australia, provides a number of examples of how a growing city can integrate urban planning and water planning to achieve sustainable urban development, environmental protection, liveability and integrated water management outcomes, and move towards becoming a “Water Sensitive City". Three examples are provided - the development at Botanic Ridge, where a 318 hectare residential development is being planned and where integrated water management options are being implemented using a “triple bottom line" sustainability investment approach; the Toolern development, which will capture and reuse stormwater and recycled water to greatly reduce the suburb-s demand for potable water, and the development at Kalkallo where a 1,200 hectare industrial precinct development is planned which will merge design of the development's water supply, sewerage services and stormwater system. The Paper argues that an integrated urban planning and water planning approach is fundamental to creating liveable, vibrant communities which meet social and financial needs while being in harmony with the local environment. Further work is required on developing investment frameworks and risk analysis frameworks to ensure that all possible solutions can be assessed equally.
Abstract: In films, visual effects have played the role of
expressing realities more realistically or describing imaginations as if
they are real. Such images are immediated images representing
realism, and the logic of immediation for the reality of images has
been perceived dominant in visual effects. In order for immediation to
have an identity as immediation, there should be the opposite concept
hypermediation.
In the mid 2000s, hypermediated images were settled as a code of
mass culture in Asia. Thus, among Asian films highly popular in those
days, this study selected five displaying hypermediated images – 2 Korean, 2 Japanese, and 1 Thailand movies – and examined the
semiotic meanings of such images using Roland Barthes- directional and implicated meaning analysis and Metz-s paradigmatic analysis
method, focusing on how hypermediated images work in the general
context of the films, how they are associated with spaces, and what
meanings they try to carry.
Abstract: In this research work, a novel parallel manipulator
with high positioning and orienting rate is introduced. This
mechanism has two rotational and one translational degree of
freedom. Kinematics and Jacobian analysis are investigated.
Moreover, workspace analysis and optimization has been performed
by using genetic algorithm toolbox in Matlab software. Because of
decreasing moving elements, it is expected much more better
dynamic performance with respect to other counterpart mechanisms
with the same degrees of freedom. In addition, using couple of
cylindrical and revolute joints increased mechanism ability to have
more extended workspace.
Abstract: For stricter drinking water regulations in the future, reducing the humic acid and disinfection byproducts in raw water, namely, trihalomethanes (THMs) and haloacetic acids (HAAs) is worthy for research. To investigate the removal of waterborne organic material using a lab-scale of bio-activated carbon filter under different EBCT, the concentrations of humic acid prepared were 0.01, 0.03, 0.06, 0.12, 0.17, 0.23, and 0.29 mg/L. Then we conducted experiments using a pilot plant with in-field of the serially connected bio-activated carbon filters and hollow fiber membrane processes employed in traditional water purification plants. Results showed under low TOC conditions of humic acid in influent (0.69 to 1.03 mg TOC/L) with an EBCT of 30 min, 40 min, and 50 min, TOC removal rates increases with greater EBCT, attaining about 39 % removal rate. The removal rate of THMs and HAAs by BACF was 54.8 % and 89.0 %, respectively.
Abstract: An experiment was conducted using two aeration
methods (water-into-air and air-into-water) and followed by filtration
processes using manganese greensand material. The properties of
groundwater such as pH, dissolved oxygen, turbidity and heavy metal
concentration (iron and manganese) will be assessed. The objectives
of this study are i) to determine the effective aeration method and ii)
to assess the effectiveness of manganese greensand as filter media in
removing iron and manganese concentration in groundwater. Results
showed that final pH for all samples after treatment are in range from
7.40 and 8.40. Both aeration methods increased the dissolved oxygen
content. Final turbidity for groundwater samples are between 3 NTU
to 29 NTU. Only three out of eight samples achieved iron
concentration of 0.3mg/L and less and all samples reach manganese
concentration of 0.1mg/L and less. Air-into-water aeration method
gives higher percentage of iron and manganese removal compare to
water-into-air method.
Abstract: An attempt was made for availability of wastewater reuse/reclamation for irrigation purposes using phytoremediation “the low cost and less technology", using six local aquatic macrophytes “e.g. T. angustifolia, B. maritimus, Ph. australis, A. donax, A. plantago-aquatica and M. longifolia (Linn)" as biological waste purifiers. Outdoor experiments/designs were conducted from May 03, 2007 till October 15, 2008, close to one of the main sewage channels of Sulaimani City/Iraq*. All processes were mainly based on conventional wastewater treatment processes, besides two further modifications were tested, the first was sand filtration pots, implanted by individual species of experimental macrophytes and the second was constructed wetlands implanted by experimental macrophytes all together. Untreated and treated wastewater samples were analyzed for their key physico-chemical properties (only heavy metals Fe, Mn, Zn and Cu with particular reference to removal efficiency by experimental macrophytes are highlighted in this paper). On the other hand, vertical contents of heavy metals were also evaluated from both pots and the cells of constructed wetland. After 135 days, macrophytes were harvested and heavy metals were analyzed in their biomass (roots/shoots) for removal efficiency assessment (i.e. uptake/ bioaccumulation rate). Results showed that; removal efficiency of all studied heavy metals was much higher in T. angustifolia followed by Ph. Australis, B. maritimus and A. donax in triple experiment sand pots. Constructed wetland experiments have revealed that; the more replicated constructed wetland cells the highest heavy metal removal efficiency was indicated.
Abstract: Recently, many web services to provide information for public transport are developed and released. They are optimized for mobile devices such a smartphone. We are also developing better path planning system for route buses and trains called “Bus-Net"[1]. However these systems only provide paths and related information before the user start moving. So we propose a context aware navigation to change the way to support public transport users. If we go to somewhere using many kinds of public transport, we have to know how to use them. In addition, public transport is dynamic system, and these have different characteristic by type. So we need information at real-time. Therefore we suggest the system that can support on user-s state. It has a variety of ways to help public transport users by each state, like turn-by-turn navigation. Context aware navigation will be able to reduce anxiety for using public transport.