Abstract: Particles are the most common and cheapest
reinforcement producing discontinuous reinforced composites with
isotropic properties. Conventional fabrication methods can be used to
produce a wide range of product forms, making them relatively
inexpensive. Optimising composite development must include
consideration of all the fundamental aspect of particles including
their size, shape, volume fraction, distribution and mechanical
properties. Research has shown that the challenges of low fracture
toughness, poor crack growth resistance and low thermal stability can
be overcome by reinforcement with particles. The unique properties
exhibited by micro particles reinforced ceramic composites have
made them to be highly attractive in a vast array of applications.
Abstract: This article is deal with the experimental
investigations of the laser diode matrixes (LDM) based on the
AlGaAs/GaAs heterostructures (lasing wavelength 790-880 nm) to
find optimal LDM parameters for active vision systems. In particular,
the dependence of LDM radiation pulse power on the pulse duration
and LDA active layer heating as well as the LDM radiation
divergence are discussed.
Abstract: Two Lithium Disilicate (LD) glass ceramics based on
SiO2-Li2O-K2O-Al2O3 system were prepared through a glass melting
method. The glass rods were then fabricated into dental crowns via a
hot pressing at 900˚C and 850˚C in order to study the effect of the
pressing temperatures on the phase formation and microstructure of
the glasses. Different samples of as cast glass and heat treated
samples (600˚C and 700˚C) were used to press for investigating the
effect of an initial microstructure on the hot pressing technique. Xray
diffraction (XRD) and scanning electron microscopy (SEM) were
performed to determine the phase formation and microstructure of the
samples, respectively. XRD results show that the main crystalline
structure was Li2Si2O5 by having Li3PO4, Li0.6Al0.6Si2O6, Li2SiO3,
Ca5 (PO4)3F and SiO2 as minor phases. Glass compositions with
different heat treatment temperatures exhibited a difference phase
formations but have less effect during pressing. SEM micrographs
showed the microstructure of Li2Si2O5 as lath-like shape in all
glasses. With increasing the initial heat treatment temperature, the
longer the lath-like crystals of lithium disilicate were increased
especially when using glass heat treatment at 700˚C followed by
pressing at 900˚C. This could be suggested that LD1 heat treatment at
700˚C which pressing at 900˚C presented the best formation by the
hot pressing and compiled microstructure.
Abstract: The author introduced the integral operator , by using this
operator a new subclasses of analytic functions are introduced. For
these classes, several Fekete-Szeg¨ type coefficient inequalities are
obtained.
Abstract: Precast residential houses are normally constructed in Malaysia using precast shear-key wall panel and this panel is designed using BS8110 where there is no provision for earthquake. However, the safety of this house under moderate and strong earthquake is still questionable. Consequently, the full-scale of residential house are designed, constructed, tested and analyzed under in-plane lateral quasi-static cyclic loading. Hysteresis loops are plotted based on the experimental work and compared with modeling of hysteresis loops using HYSTERES in RUAUMOKO 2D program. Modified Takeda hysteresis model is chosen to behave a similar pattern with experimental work. This program will display the earthquake excitations, spectral displacements, pseudo spectral acceleration, mode shape and deformation of the structure. It can be concluded that this building is suffering severe cracks and damage under moderate and severe earthquake.
Abstract: Augmented Reality is a technology that involves the
overlay of virtual content, which is context or environment sensitive,
on images of the physical world in real time. This paper presents the
development of a catalog system that facilitates and allows the
creation, publishing, management and exploitation of augmented
multimedia contents and Augmented Reality applications, creating an
own space for anyone that wants to provide information to real
objects in order to edit and share it then online with others. These
spaces would be built for different domains without the initial need of
expert users. Its operation focuses on the context of Web 2.0 or
Social Web, with its various applications, developing contents to
enrich the real context in which human beings act permitting the
evolution of catalog’s contents in an emerging way.
Abstract: This paper describes a logical method to enhance
security on the grid computing to restrict the misuse of the grid
resources. This method is an economic and efficient one to avoid the
usage of the special devices. The security issues, techniques and
solutions needed to provide a secure grid computing environment are
described. A well defined process for security management among
the resource accesses and key holding algorithm is also proposed. In
this method, the identity management, access control and
authorization and authentication are effectively handled.
Abstract: The purpose of this paper is to evaluate the positive
impact of SHRM practices and transformational leadership style on
employees job satisfaction and to develop a conceptual understanding
of the moderating role of transformational leadership between the
relationship of SHRM practices and employees job satisfaction. This
study focuses on four SHRM practices that have positive relationship
with employee’s job satisfaction.
Abstract: Mammography has been one of the most reliable
methods for early detection of breast cancer. There are different
lesions which are breast cancer characteristic such as
microcalcifications, masses, architectural distortions and bilateral
asymmetry. One of the major challenges of analysing digital
mammogram is how to extract efficient features from it for accurate
cancer classification. In this paper we proposed a hybrid feature
extraction method to detect and classify all four signs of breast
cancer. The proposed method is based on multiscale surrounding
region dependence method, Gabor filters, multi fractal analysis,
directional and morphological analysis. The extracted features are
input to self adaptive resource allocation network (SRAN) classifier
for classification. The validity of our approach is extensively
demonstrated using the two benchmark data sets Mammographic
Image Analysis Society (MIAS) and Digital Database for Screening
Mammograph (DDSM) and the results have been proved to be
progressive.
Abstract: Key frame extraction methods select the most
representative frames of a video, which can be used in different areas
of video processing such as video retrieval, video summary, and video
indexing. In this paper we present a novel approach for extracting key
frames from video sequences. The frame is characterized uniquely by
his contours which are represented by the dominant blocks. These
dominant blocks are located on the contours and its near textures.
When the video frames have a noticeable changement, its dominant
blocks changed, then we can extracte a key frame. The dominant
blocks of every frame is computed, and then feature vectors are
extracted from the dominant blocks image of each frame and arranged
in a feature matrix. Singular Value Decomposition is used to calculate
sliding windows ranks of those matrices. Finally the computed ranks
are traced and then we are able to extract key frames of a video.
Experimental results show that the proposed approach is robust
against a large range of digital effects used during shot transition.
Abstract: Forging parts is used to automobiles; because, they have high strength and it is possible to press them into complicated shape. When itis possible to manufacture hollow forging parts, it leads to reduce weightof the automobiles. But, hollow forging parts are confined to axisymmetrical shape. Hollowforging parts that were pressed to complicated shape are expected. Therefore, we forge a blank that aluminum alloy was inserted in stainless steel. After that, we can providecomplex forging parts that are reduced weight,ifit is possible to be melted the aluminum alloy away by using different of melting points.It is necessary to establish heat forging analysis methodon blank consist of stainless steel and aluminum alloy. Because,this forging is different from conventional forging and this technology is not confirmed. In this study, we compared forging experiment with numerical analysis on the view point of forming load and shape after forming and establish how to set the material temperaturesof two metals and material property of stainless steel on the analysis method. Consequently, temperature difference of stainless steel and aluminum alloy was obtained by experiment. We got material property of stainless steel on forging experimental by compression tests. We had compared numerical analysis that was used the temperature difference of two metals and the material property of stainless steel on forging experimental with forging experiment. Forging analysis method on blankconsist of two metals was established by result of numerical analysis having agreedwith result of forging experiment.
Abstract: In sheet metal forming process, raw material
mechanical properties are important parameters. This paper is to
compare the wall’s incline angle or formability of SS 400 steel and
SUS 304 stainless steel in single point incremental forming. The two
materials are ferrous base alloyed, which have the different unit cell,
mechanical property and chemical composition. They were forming
into cone shape specimens having 100 mm diameter with different
wall’s incline angle: 90o, 75o and 60o. The investigation was
continued until the specimens formed surface facture. The
experimental result showed that the smaller the wall incline angle
higher the formability with the both materials. The formability limit
of the ferrous base alloy was approx. 60o wall’s incline angle. By
nature, SS 400 has higher formability than SUS 304. This result can
be used as the initial data in designing the single point incremental
forming parts.
Abstract: Powder metallurgy (P/M) is the only economic way to
produce porous parts/products. P/M can produce near net shape parts
hence reduces wastage of raw material and energy, avoids various
machining operations. The most vital use of P/M is in production of
metallic filters and self lubricating bush bearings and siding surfaces.
The porosity of the part can be controlled by varying compaction
pressure, sintering temperature and composition of metal powder
mix. The present work is aimed for experimental analysis of friction
and wear properties of self lubricating copper and tin bush bearing.
Experimental results confirm that wear rate of sintered component
is lesser for components having 10% tin by weight percentage. Wear
rate increases for high tin percentage (experimented for 20% tin and
30% tin) at same sintering temperature. Experimental results also
confirms that wear rate of sintered component is also dependent on
sintering temperature, soaking period, composition of the preform,
compacting pressure, powder particle shape and size.
Interfacial friction between die and punch, between inter powder
particles, between die face and powder particle depends on
compaction pressure, powder particle size and shape, size and shape
of component which decides size & shape of die & punch, material of
die & punch and material of powder particles.
Abstract: The purpose of this work is examining the multiproduct
multi-stage in a battery production line. To improve the
performances of an assembly production line by determine the
efficiency of each workstation. Data collected from every
workstation. The data are throughput rate, number of operator, and
number of parts that arrive and leaves during part processing. Data
for the number of parts that arrives and leaves are collected at least at
the amount of ten samples to make the data is possible to be analyzed
by Chi-Squared Goodness Test and queuing theory. Measures of this
model served as the comparison with the standard data available in
the company. Validation of the task time value resulted by comparing
it with the task time value based on the company database. Some
performance factors for the multi-product multi-stage in a battery
production line in this work are shown.
The efficiency in each workstation was also shown. Total
production time to produce each part can be determined by adding
the total task time in each workstation. To reduce the queuing time
and increase the efficiency based on the analysis any probably
improvement should be done. One probably action is by increasing
the number of operators how manually operate this workstation.
Abstract: Applied industrial engineering is concerned with
imparting employable skills to improve the productivity for current
situation of products and services. The purpose of this case study is to
present the results of an initial research study conducted to identify
the desired professional characteristics of an industrial engineer with
an undergraduate degree and the emerging topic areas that should be
incorporated into the curriculum to prepare industrial engineering
(IE) graduates for the future workforce. Conclusions and
recommendations for applied industrial engineering syllabus have
been gathered and reported below. A two-pronged approach was
taken which included a method of benchmarking by comparing the
applied industrial engineering curricula of various universities and an
industry survey to identify job market requirements. This
methodology produced an analysis of the changing nature of
industrial engineering from learning to practical education. A
curriculum study for engineering is a relatively unexplored area of
research in the Middle East, much less for applied industrial
engineering. This work is an effort to bridge the gap between
theoretical study in the classroom and the real world work
applications in the industrial and service sectors.
Abstract: In today’s era, it is no news that organizations should
demonstrate honest conduct as well as ethical administration.
Therefore, the concept of corporate social responsibility
(subsequently CSR) has created its tag upon the company’s focal
point as well as marketing communications, and will continue in the
future. The importance of CSR has increased in the last decade, and
this concept has attracted global attention. The notion of CSR has
strategic significance for many organizations. However, businesses
are not adapting the activities of CSR that benefit to all of its
stakeholders (including society). The main reason is the practitioners
are unfortunately unable to comprehend its importance; and
therefore, the activities of the CSR are so detached from the business
activities. Hence, it is required to develop an understanding that the
activities of CSR are not only beneficial for the society but it also
benefit to business. This paper focuses on the concept of strategic
CSR, and develops a theoretical framework that will help
practitioners to filter and chose the activities of CSR that are strategic
in nature.
Abstract: In this paper, the influence of upstream structures on the flow patternaround and inside the wind-catcher is experimentally investigated by smoke flow visualization techniques. Wind-catchers are an important part of natural ventilation in residential buildings or public places such as shopping centers, libraries, etc. Wind-catchers might be also used in places of high urban densities; hence their potential to provide natural ventilation is dependent on the presence of upstream structures. In this study, the two-sided wind-catcher model was based on a real wind-catcher observed in the city of Yazd, Iran. The present study focuses on the flow patterns around and inside the isolated two-sided wind-catcher, and on a two-sided wind-catcher in the presence of an upstream structure. The results show that the presence of an upstream structure influences the airflow pattern force and direction. Placing a high upstream structure reverses the airflow direction inside the wind-catcher.
Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: In the cloud computing hierarchy IaaS is the lowest
layer, all other layers are built over it. Thus it is the most important
layer of cloud and requisite more importance. Along with advantages
IaaS faces some serious security related issue. Mainly Security
focuses on Integrity, confidentiality and availability. Cloud
computing facilitate to share the resources inside as well as outside of
the cloud. On the other hand, cloud still not in the state to provide
surety to 100% data security. Cloud provider must ensure that end
user/client get a Quality of Service. In this report we describe
possible aspects of cloud related security.
Abstract: Botnets are one of the most serious and widespread
cyber threats. Today botnets have been facilitating many
cybercrimes, especially financial, top secret thefts. Botnets can be
available for lease in the market and are utilized by the
cybercriminals to launch massive attacks like DDoS, click fraud,
phishing attacks etc., Several large institutions, hospitals, banks,
government organizations and many social networks such as twitter,
facebook etc., became the target of the botmasters. Recently,
noteworthy researches have been carried out to detect bot, C&C
channels, botnet and botmasters. Using many sophisticated
technologies, botmasters made botnet a titan of the cyber world.
Innumerable challenges have been put forth by the botmasters to the
researchers in the detection of botnet. In this paper we present a
survey of different types of botnet C&C channels and also provide a
comparison of various botnet categories. Finally we hope that our
survey will create awareness for forthcoming botnet research
endeavors.