Abstract: This paper puts forward one kind of air-fuel ratio
control method with PI controller. With the help of
MATLAB/SIMULINK software, the mathematical model of air-fuel
ratio control system for distributorless CNG engine is constructed.
The objective is to maintain cylinder-to-cylinder air-fuel ratio at a
prescribed set point, determined primarily by the state of the Three-
Way-Catalyst (TWC), so that the pollutants in the exhaust are
removed with the highest efficiency. The concurrent control of airfuel
under transient conditions could be implemented by Proportional
and Integral (PI) controller. The simulation result indicates that the
control methods can easily eliminate the air/fuel maldistribution and
maintain the air/fuel ratio at the stochiometry within minimum
engine events.
Abstract: The mobile users with Laptops need to have an
efficient access to i.e. their home personal data or to the Internet from
any place in the world, regardless of their location or point of
attachment, especially while roaming outside the home subnet. An
efficient interpretation of packet losses problem that is encountered
from this roaming is to the centric of all aspects in this work, to be
over-highlighted. The main previous works, such as BER-systems,
Amigos, and ns-2 implementation that are considered to be in
conjunction with that problem under study are reviewed and
discussed. Their drawbacks and limitations, of stopping only at
monitoring, and not to provide an actual solution for eliminating or
even restricting these losses, are mentioned. Besides that, the
framework around which we built a Triple-R sequence as a costeffective
solution to eliminate the packet losses and bridge the gap
between subnets, an area that until now has been largely neglected, is
presented. The results show that, in addition to the high bit error rate
of wireless mobile networks, mainly the low efficiency of mobile-IP
registration procedure is a direct cause of these packet losses.
Furthermore, the output of packet losses interpretation resulted an
illustrated triangle of the registration process. This triangle should be
further researched and analyzed in our future work.
Abstract: Atmospheric stability plays the most important role in
the transport and dispersion of air pollutants. Different methods are
used for stability determination with varying degrees of complexity.
Most of these methods are based on the relative magnitude of
convective and mechanical turbulence in atmospheric motions.
Richardson number, Monin-Obukhov length, Pasquill-Gifford
stability classification and Pasquill–Turner stability classification, are
the most common parameters and methods. The Pasquill–Turner
Method (PTM), which is employed in this study, makes use of
observations of wind speed, insolation and the time of day to classify
atmospheric stability with distinguishable indices. In this study, a
model is presented to determination of atmospheric stability
conditions using PTM. As a case study, meteorological data of
Mehrabad station in Tehran from 2000 to 2005 is applied to model.
Here, three different categories are considered to deduce the pattern
of stability conditions. First, the total pattern of stability classification
is obtained and results show that atmosphere is 38.77%, 27.26%,
33.97%, at stable, neutral and unstable condition, respectively. It is
also observed that days are mostly unstable (66.50%) while nights are
mostly stable (72.55%). Second, monthly and seasonal patterns are
derived and results indicate that relative frequency of stable
conditions decrease during January to June and increase during June
to December, while results for unstable conditions are exactly in
opposite manner. Autumn is the most stable season with relative
frequency of 50.69% for stable condition, whilst, it is 42.79%,
34.38% and 27.08% for winter, summer and spring, respectively.
Hourly stability pattern is the third category that points out that
unstable condition is dominant from approximately 03-15 GTM and
04-12 GTM for warm and cold seasons, respectively. Finally,
correlation between atmospheric stability and CO concentration is
achieved.
Abstract: It is important to provide possibility of so called
“handover" for the mobile subscriber from GSM network to Wi-Fi
network and back. To solve specified problem it is necessary to
estimate connection time between base station and wireless access
point. Difficulty to estimate this parameter is that it doesn-t described
in specifications of the standard and, hence, no recommended value
is given.
In this paper, the analytical model is presented that allows the
estimating connection time between base station and IEEE 802.11
access point.
Abstract: When trying to enumerate all BIBD-s for given parameters,
their natural solution space appears to be huge and grows extremely with the number of points of the design. Therefore,
constructive enumerations are often carried out by assuming additional
constraints on design-s structure, automorphisms being mostly used ones. It remains a hard task to construct designs with trivial
automorphism group – those with no additional symmetry – although it is believed that most of the BIBD-s belong to that case. In
this paper, very many new designs with parameters 2-(13, 5, 5), 2-(16, 6, 5) and 2-(21, 6, 4) are constructed, assuming an action of an
automorphism of order 3. Even more, it was possible to construct millions of such designs with no non-trivial automorphisms.
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: Data Warehouses (DWs) are repositories which contain the unified history of an enterprise for decision support. The data must be Extracted from information sources, Transformed and integrated to be Loaded (ETL) into the DW, using ETL tools. These tools focus on data movement, where the models are only used as a means to this aim. Under a conceptual viewpoint, the authors want to innovate the ETL process in two ways: 1) to make clear compatibility between models in a declarative fashion, using correspondence assertions and 2) to identify the instances of different sources that represent the same entity in the real-world. This paper presents the overview of the proposed framework to model the ETL process, which is based on the use of a reference model and perspective schemata. This approach provides the designer with a better understanding of the semantic associated with the ETL process.
Abstract: Finding the shortest path between two positions is a
fundamental problem in transportation, routing, and communications
applications. In robot motion planning, the robot should pass around
the obstacles touching none of them, i.e. the goal is to find a
collision-free path from a starting to a target position. This task has
many specific formulations depending on the shape of obstacles,
allowable directions of movements, knowledge of the scene, etc.
Research of path planning has yielded many fundamentally different
approaches to its solution, mainly based on various decomposition
and roadmap methods. In this paper, we show a possible use of
visibility graphs in point-to-point motion planning in the Euclidean
plane and an alternative approach using Voronoi diagrams that
decreases the probability of collisions with obstacles. The second
application area, investigated here, is focused on problems of finding
minimal networks connecting a set of given points in the plane using
either only straight connections between pairs of points (minimum
spanning tree) or allowing the addition of auxiliary points to the set
to obtain shorter spanning networks (minimum Steiner tree).
Abstract: The quantum mechanics simulation was applied for
calculating the interaction force between 2 molecules based on atomic level. For the simple extractive distillation system, it is ternary
components consisting of 2 closed boiling point components (A,lower boiling point and B, higher boiling point) and solvent (S). The
quantum mechanics simulation was used to calculate the intermolecular force (interaction force) between the closed boiling
point components and solvents consisting of intermolecular between
A-S and B-S.
The requirement of the promising solvent for extractive distillation
is that solvent (S) has to form stronger intermolecular force with only
one component than the other component (A or B). In this study, the
systems of aromatic-aromatic, aromatic-cycloparaffin, and paraffindiolefin
systems were selected as the demonstration for solvent
selection. This study defined new term using for screening the solvents called relative interaction force which is calculated from the
quantum mechanics simulation. The results showed that relative
interaction force gave the good agreement with the literature data
(relative volatilities from the experiment). The reasons are discussed. Finally, this study suggests that quantum mechanics results can improve the relative volatility estimation for screening the solvents leading to reduce time and money consuming
Abstract: This study focuses on an evaluation of Hokkaido which
is the northernmost and largest prefecture by surface area in Japan and
particularly on two points: the rivalry between all kinds of land use
such as urban land and agricultural and forestry land in various cities
and their surrounding areas and the possibilities for forestry biomass in
areas other than those mentioned above and grasps which areas require
examination of the nature of land use control and guidance through
conducting land use analysis at the district level using GIS
(Geographic Information Systems). The results of analysis in this
study demonstrated that it is essential to divide the whole of Hokkaido
into two areas: those within delineated city planning areas and those
outside of delineated city planning areas and to conduct an evaluation
of each land use control.
In delineated urban areas, particularly urban areas, it is essential to
re-examine land use from the point of view of compact cities or smart
cities along with conducting an evaluation of land use control that
focuses on issues of rivalry between all kinds of land use such as urban
land and agricultural and forestry land. In areas outside of delineated
urban areas, it is desirable to aim to build a specific community
recycling range based on forest biomass utilization by conducting an
evaluation of land use control concerning the possibilities for forest
biomass focusing particularly on forests within and outside of city
planning areas.
Abstract: In this paper, a model for an information retrieval
system is proposed which takes into account that knowledge about
documents and information need of users are dynamic. Two
methods are combined, one qualitative or symbolic and the other
quantitative or numeric, which are deemed suitable for many
clustering contexts, data analysis, concept exploring and
knowledge discovery. These two methods may be classified as
inductive learning techniques. In this model, they are introduced to
build “long term" knowledge about past queries and concepts in a
collection of documents. The “long term" knowledge can guide
and assist the user to formulate an initial query and can be
exploited in the process of retrieving relevant information. The
different kinds of knowledge are organized in different points of
view. This may be considered an enrichment of the exploration
level which is coherent with the concept of document/query
structure.
Abstract: A game animals – elk (Alces alces), deer (Cervus
elaphus), roe deer (Capreolus capreolus) or wild boar (Sus scrofa
scrofa) - every autumn and winter period provide an excellent
investment, diversification of many consumer meals. In last years
consumption and assortiment of game meat products significantly
increase. Investigations about biochemical composition of game meat
are not very much. The meat of wild animals is more favourable for
human health because it has lower saturated fatty acids content, but
higher content of protein. Therefore the aim of investigations was to
compare biochemical composition of ungulates obtained in
Latvia.Investigations were carried out in wild animals different
regions of Latvia. In the studied samples protein, intramuscular fat,
fatty acids and cholesterol were determined. The biochemical
analysis of 54 samples were done. Results of analysis showed that
protein content 22.36 – 22.92% of all types of meat samples is not
different statistically, significantly lower fat content 1.33 ± 0.88%
had elk meat samples and 1.59 ± 0.59% roe deer samples. Content of
cholesterol was various 64.41 – 95.07% in the ruminant meat
samples of different species. From the dietetic point of view the best
composition of fatty acids has meat samples of roe deer.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: After the development of the Internet a suitable
discipline for trading goods electronically has been emerged.
However, this type of markets is not still mature enough in order to
become independent and get closer to seller/buyer-s needs.
Furthermore, the buyable and sellable goods in these markets still
don-t have essential standards for being well-defined. In this paper,
we will present a model for development of a market which can
contain goods with variable definitions and we will also investigate
its characteristics. Besides, by noticing the fact that people have
different discriminations, it-s figured out that the significance of each
attribute of a specific product may vary from different people-s view
points. Consequently we-ll present a model for weighting and
accordingly different people-s view points could be satisfied. These
two aspects will be discussed completely throughout this paper.
Abstract: In this paper we proposed a novel method to acquire
the ROI (Region of interest) of unsupervised and touch-less palmprint
captured from a web camera in real-time. We use Viola-Jones
approach and skin model to get the target area in real time. Then an
innovative course-to-fine approach to detect the key points on the hand
is described. A new algorithm is used to find the candidate key points
coarsely and quickly. In finely stage, we verify the hand key points
with the shape context descriptor. To make the user much comfortable,
it can process the hand image with different poses, even the hand is
closed. Experiments show promising result by using the proposed
method in various conditions.
Abstract: The RK1GL2X3 method is a numerical method for solving initial value problems in ordinary differential equations, and is based on the RK1GL2 method which, in turn, is a particular case of the general RKrGLm method. The RK1GL2X3 method is a fourth-order method, even though its underlying Runge-Kutta method RK1 is the first-order Euler method, and hence, RK1GL2X3 is considerably more efficient than RK1. This enhancement is achieved through an implementation involving triple-nested two-point Gauss- Legendre quadrature.
Abstract: This paper proposes an architecture of dynamically
reconfigurable arithmetic circuit. Dynamic reconfiguration is a
technique to realize required functions by changing hardware
construction during operations. The proposed circuit is based on a
complex number multiply-accumulation circuit which is used
frequently in the field of digital signal processing. In addition, the
proposed circuit performs real number double precision arithmetic
operations. The data formats are single and double precision floating
point number based on IEEE754. The proposed circuit is designed
using VHDL, and verified the correct operation by simulations and
experiments.
Abstract: Alternative energy is any energy source that is an alternative to fossil fuel. These alternatives are intended to address concerns about such fossil fuels. Today, because of the variety of energy choices and differing goals of their advocates, defining some energy types as "alternative" is highly controversial. Most of the recent and existing alternative sources of energy are discussed below
Abstract: The notion of intuitionistic fuzzy sets was introduced
by Atanassov as a generalization of the notion of fuzzy sets. Y.B. Jun
and S.Z. Song introduced the notion of intuitionistic fuzzy points.
In this paper we find some relations between the intuitionistic fuzzy
ideals of a semigroup S and the set of all intuitionistic fuzzy points
of S.
Abstract: Modeling and vibration of a flexible link manipulator
with tow flexible links and rigid joints are investigated which can
include an arbitrary number of flexible links. Hamilton principle and
finite element approach is proposed to model the dynamics of
flexible manipulators. The links are assumed to be deflection due to
bending. The association between elastic displacements of links is
investigated, took into account the coupling effects of elastic motion
and rigid motion. Flexible links are treated as Euler-Bernoulli beams
and the shear deformation is thus abandoned. The dynamic behavior
due to flexibility of links is well demonstrated through numerical
simulation. The rigid-body motion and elastic deformations are
separated by linearizing the equations of motion around the rigid
body reference path. Simulation results are shown on for both
position and force trajectory tracking tasks in the presence of varying
parameters and unknown dynamics remarkably well. The proposed
method can be used in both dynamic simulation and controller
design.