Abstract: The paper deals with current issues in research of
advanced methods to increase reliability of traditional timber
structural elements. It analyses the issue of strengthening of bent
timber beams, such as ceiling beams in old (historical) buildings with
additional concrete slab in combination with externally bonded fibre -
reinforced polymer. The paper describes experimental testing of
composite timber-concrete beam with FRP reinforcement and
compares results with FEM analysis.
Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: Class cohesion is a key object-oriented software
quality attribute that is used to evaluate the degree of relatedness of
class attributes and methods. Researchers have proposed several class
cohesion measures. However, the effect of considering the special
methods (i.e., constructors, destructors, and access and delegation
methods) in cohesion calculation is not thoroughly theoretically
studied for most of them. In this paper, we address this issue for three
popular connectivity-based class cohesion measures. For each of the
considered measures we theoretically study the impact of including
or excluding special methods on the values that are obtained by
applying the measure. This study is based on analyzing the
definitions and formulas that are proposed for the measures. The
results show that including/excluding special methods has a
considerable effect on the obtained cohesion values and that this
effect varies from one measure to another. For each of the three
connectivity-based measures, the proposed theoretical study
recommended excluding the special methods in cohesion
measurement.
Abstract: The success of any retail business is predisposed by its
swift response and its knack in understanding the constraints and the
requirements of customers. In this paper a conceptual design model
of an automated customer-friendly supermarket has been proposed.
In this model a 10-sided, space benefited, regular polygon shaped
gravity shelves have been designed for goods storage and effective
customer-specific algorithms have been built-in for quick automatic
delivery of the randomly listed goods. The algorithm is developed
with two main objectives, viz., delivery time and priority. For
meeting these objectives the randomly listed items are reorganized
according to the critical-path of the robotic arm specific to the
identified shop and its layout and the items are categorized according
to the demand, shape, size, similarity and nature of the product for an
efficient pick-up, packing and delivery process. We conjectured that
the proposed automated supermarket model reduces business
operating costs with much customer satisfaction warranting a winwin
situation.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.
Abstract: The Sigma-Delta A/D converters have been proposed
as a practical application for A/D conversion at high rates because of
its simplicity and robustness to imperfections in the circuit, also
because the traditional converters are more difficult to implement in
VLSI technology. These difficulties with conventional conversion
methods need precise analog components in their filters and
conversion circuits, and are more vulnerable to noise and
interference. This paper aims to analyze the architecture, function and
application of Analog-Digital converters (A/D) Sigma-Delta to
overcome these difficulties, showing some simulations using the
Simulink software and Multisim.
Abstract: A simple, accurate and precise direct spectrophotometric method has been developed for the determination of cefixime in tablets and capsules. The method is based on the reaction of cefixime with a mixture of potassium iodide and potassium iodate to form yellow coloured product in ethanol-distilled water medium at room temperature which absorbed maximally at 352 nm. The factors affecting the reaction product were carefully studied and optimized. The validation parameters based on International Conference on Harmonisation (ICH, USA) guidelines were followed. The effect of common excipients used as additives has been tested and the tolerance limit was calculated for the determination of cefixime. Beer’s law is obeyed in the concentration range of 4 – 24 ug mL-1 with apparent molar absorptivity of 1.52 × 104 L mol-1cm-1 and Sandell’s sensitivity of 0.033 ug/cm2/ 0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.32 and 1.06 ug mL-1, respectively. The proposed method has been successfully applied for the determination of cefixime in pharmaceutical formulations. The results obtained by the proposed method were statistically compared with the reference method using t- and F- values and found no significant difference between the two methods. The proposed method can be used as an alternate method for routine quality control analysis of cefixime in pharmaceutical formulations.
Abstract: In addition to the production, which is already
frequently optimized, improving the distribution logistics also opens
up tremendous potential for increasing an enterprise’s
competitiveness. Here too though, numerous interactions need to be
taken into account, enterprises thus need to be able to identify and
weigh between different potentials for economically efficient
optimizations. In order to be able to assess potentials, enterprises
require a suitable method. This paper first briefly presents the need
for this research before introducing the procedure that will be used to
develop an appropriate method that not only considers interactions
but is also quickly and easily implemented.
Abstract: The aim of the present study is to investigate the
potential use of the selected seed oils. The oil was extracted using
Soxhlet apparatus and the physicochemical characteristics of the oil
determined using standard methods. The following results were
obtained for the physicochemical parameters analysed: for Egusi seed
oil, Oil yield 53.20%, Saponification value 178.03±1.25 mgKOH/g,
Iodine value 49.10±0.32 g I2/100g, Acid value 4.30±0.86 mgKOH/g,
and Peroxide value 5.80±0.27 meq/kg were obtained. For Pawpaw
seed oil, Oil yield 40.10%, Saponification value 24.13±3.93
mgKOH/g, Iodine value 24.87±0.19 g I2/100g, Acid value 9.46±0.40
mgKOH/g, and Peroxide value 3.12±1.22 meq/kg were obtained. For
Sweet orange seed oil, Oil yield 43.10%, Saponification value
106.30±2.37 mgKOH/g, Iodine value 37.08±0.04 g I2/100g, Acid
value 7.59±0.77 mgKOH/g, and Peroxide value 2.21±0.46 meq/kg
were obtained. From the obtained values of the determined
parameters, the oils can be extracted from the three selected seeds in
commercial quantities and that the egusi and sweet orange seed oils
may be utilized in the industrial soap production.
Abstract: The lactic acid bacteria (LAB) were isolated from
10 samples of fermented foods (Sa-tor-dong and Bodo) in South
locality of Thailand. The 23 isolates of lactic acid bacteria were
selected, which were exhibited a clear zone and growth on MRS
agar supplemented with CaCO3. All of lactic acid bacteria were
tested on morphological and biochemical. The result showed that
all isolates were Gram’s positive, non-spore forming but only
10 isolates displayed catalase negative. The 10 isolates including
BD1 .1, BD 1.2, BD 2.1, BD2.2, BD 2.3, BD 3.1, BD 4.1, BD 5.2,
ST 4.1 and ST 5.2 were selected for inhibition activity
determination. Only 2 strains (ST 4.1 and BD 2.3) showed
inhibition zone on agar, when using Escherichia coli sp. as target
strain. The ST 4.1 showed highest inhibition zone on agar, which
was selected for probiotic property testing. The ST4.1 isolate
could grow in MRS broth containing a high concentration of
sodium chloride 6%, bile salts 7%, pH 4-10 and vary temperature
at 15-45°C.
Abstract: The measured data obtained from sensors in
continuous monitoring of civil structures are mainly used for modal
identification and damage detection. Therefore, when modal
identification analysis is carried out the quality in the identification of
the modes will highly influence the damage detection results. It is
also widely recognized that the usefulness of the measured data used
for modal identification and damage detection is significantly
influenced by the number and locations of sensors. The objective of
this study is the numerical implementation of two widely known
optimum sensor placement methods in beam-like structures.
Abstract: Voltage sags are the most common power quality
disturbance in the distribution system. It occurs due to the fault in the
electrical network or by the starting of a large induction motor and
this can be solved by using the custom power devices such as
Dynamic Voltage Restorer (DVR). In this paper DVR is proposed to
compensate voltage sags on critical loads dynamically. The DVR
consists of VSC, injection transformers, passive filters and energy
storage (lead acid battery). By injecting an appropriate voltage, the
DVR restores a voltage waveform and ensures constant load voltage.
The simulation and experimental results of a DVR using MATLAB
software shows clearly the performance of the DVR in mitigating
voltage sags.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: In this study, a comparative analysis of the approaches
associated with the use of neural network algorithms for effective
solution of a complex inverse problem – the problem of identifying
and determining the individual concentrations of inorganic salts in
multicomponent aqueous solutions by the spectra of Raman
scattering of light – is performed. It is shown that application of
artificial neural networks provides the average accuracy of
determination of concentration of each salt no worse than 0.025 M.
The results of comparative analysis of input data compression
methods are presented. It is demonstrated that use of uniform
aggregation of input features allows decreasing the error of
determination of individual concentrations of components by 16-18%
on the average.
Abstract: In this paper we make a temperature investigations in
two type of superposed crimped connections using experimental
determinations. All the samples use 8 copper wire 7.1 x 3 mm2
crimped by two methods: the first method uses one crimp indents and
the second is a proposed method with two crimp indents. The ferrule
is a parallel one. We study the influence of number and position of
crimp indents. The samples are heated in A.C. current at different
current values until steady state heating regime. After obtaining of
temperature values, we compare them and present the conclusion.
Abstract: Color Histogram is considered as the oldest method
used by CBIR systems for indexing images. In turn, the global
histograms do not include the spatial information; this is why the
other techniques coming later have attempted to encounter this
limitation by involving the segmentation task as a preprocessing step.
The weak segmentation is employed by the local histograms while
other methods as CCV (Color Coherent Vector) are based on strong
segmentation. The indexation based on local histograms consists of
splitting the image into N overlapping blocks or sub-regions, and
then the histogram of each block is computed. The dissimilarity
between two images is reduced, as consequence, to compute the
distance between the N local histograms of the both images resulting
then in N*N values; generally, the lowest value is taken into account
to rank images, that means that the lowest value is that which helps to
designate which sub-region utilized to index images of the collection
being asked. In this paper, we make under light the local histogram
indexation method in the hope to compare the results obtained against
those given by the global histogram. We address also another
noteworthy issue when Relying on local histograms namely which
value, among N*N values, to trust on when comparing images, in
other words, which sub-region among the N*N sub-regions on which
we base to index images. Based on the results achieved here, it seems
that relying on the local histograms, which needs to pose an extra
overhead on the system by involving another preprocessing step
naming segmentation, does not necessary mean that it produces better
results. In addition to that, we have proposed here some ideas to
select the local histogram on which we rely on to encode the image
rather than relying on the local histogram having lowest distance with
the query histograms.
Abstract: Two types of commercial cylindrical lithium ion
batteries (Panasonic 3.4 Ah NCR-18650B and Samsung 2.9 Ah
INR-18650), were investigated experimentally. The capacities of these
samples were individually measured using constant current-constant
voltage (CC-CV) method at different ambient temperatures (-10°C,
0°C, 25°C). Their internal resistance was determined by
electrochemical impedance spectroscopy (EIS) and pulse discharge
methods. The cells with different configurations of parallel connection
NCR-NCR, INR-INR and NCR-INR were charged/discharged at the
aforementioned ambient temperatures. The results showed that the
difference of internal resistance between cells much more evident at
low temperatures. Furthermore, the parallel connection of NCR-NCR
exhibits the most uniform temperature distribution in cells at -10°C,
this feature is quite favorable for the safety of the battery pack.
Abstract: The article presents the trends in Georgian wine
market development and evaluates the competitive advantages of
Georgia to enter the wine market based on its customs, traditions and
historical practices combined with modern technologies.
In order to analyze the supply of wine, dynamics of vineyard land
area and grape varieties are discussed, trends in wine production are
presented, trends in export and import are evaluated, local wine
market, its micro and macro environments are studied and analyzed
based on the interviews with experts and analysis of initial recording
materials.
For strengthening its position on the international market, the level
of competitiveness of Georgian wine is defined, which is evaluated
by “ex-ante” and “ex-post” methods, as well as by four basic and two
additional factors of the Porter’s diamond method; potential
advantages and disadvantages of Georgian wine are revealed.
Conclusions are made by identifying the factors that hinder the
development of Georgian wine market. Based on the conclusions,
relevant recommendations are developed.
Abstract: The importance of the formal specification in the
software life cycle is barely concealing to anyone. Formal
specifications use mathematical notation to describe the properties of
information system precisely, without unduly constraining the way in
how these properties are achieved. Having a correct and quality
software specification is not easy task. This study concerns with how
a group of rectifiers can communicate with each other and work to
prepare and produce a correct formal software specification. WBCS
has been implemented based mainly in the proposed supported
cooperative work model and a survey conducted on the existing Webbased
collaborative writing tools. This paper aims to assess the
feasibility of executing the web-based collaboration process using
WBCS. The purpose of conducting this test is to test the system as a
whole for functionality and fitness for use based on the evaluation
test plan.
Abstract: Recent perceived climate variability raises concerns
with unprecedented hydrological phenomena and extremes.
Distribution and circulation of the waters of the Earth become
increasingly difficult to determine because of additional uncertainty
related to anthropogenic emissions. The world wide observed
changes in the large-scale hydrological cycle have been related to an
increase in the observed temperature over several decades. Although
the effect of change in climate on hydrology provides a general
picture of possible hydrological global change, new tools and
frameworks for modelling hydrological series with nonstationary
characteristics at finer scales, are required for assessing climate
change impacts. Of the downscaling techniques, dynamic
downscaling is usually based on the use of Regional Climate Models
(RCMs), which generate finer resolution output based on atmospheric
physics over a region using General Circulation Model (GCM) fields
as boundary conditions. However, RCMs are not expected to capture
the observed spatial precipitation extremes at a fine cell scale or at a
basin scale. Statistical downscaling derives a statistical or empirical
relationship between the variables simulated by the GCMs, called
predictors, and station-scale hydrologic variables, called predictands.
The main focus of the paper is on the need for using statistical
downscaling techniques for projection of local hydrometeorological
variables under climate change scenarios. The projections can be then
served as a means of input source to various hydrologic models to
obtain streamflow, evapotranspiration, soil moisture and other
hydrological variables of interest.