Abstract: Distributed Power generation has gained a lot of
attention in recent times due to constraints associated with
conventional power generation and new advancements in DG
technologies .The need to operate the power system economically
and with optimum levels of reliability has further led to an increase
in interest in Distributed Generation. However it is important to place
Distributed Generator on an optimum location so that the purpose of
loss minimization and voltage regulation is dully served on the
feeder. This paper investigates the impact of DG units installation on
electric losses, reliability and voltage profile of distribution networks.
In this paper, our aim would be to find optimal distributed
generation allocation for loss reduction subjected to constraint of
voltage regulation in distribution network. The system is further
analyzed for increased levels of Reliability. Distributed Generator
offers the additional advantage of increase in reliability levels as
suggested by the improvements in various reliability indices such as
SAIDI, CAIDI and AENS. Comparative studies are performed and
related results are addressed. An analytical technique is used in order
to find the optimal location of Distributed Generator. The suggested
technique is programmed under MATLAB software. The results
clearly indicate that DG can reduce the electrical line loss while
simultaneously improving the reliability of the system.
Abstract: Saccharomyces cerevisiae (baker-s yeast) can exhibit
sustained oscillations during the operation in a continuous bioreactor
that adversely affects its stability and productivity. Because of
heterogeneous nature of cell populations, the cell population balance
models can be used to capture the dynamic behavior of such cultures.
In this paper an unstructured, segregated model is used which is
based on population balance equation(PBE) and then in order to
simulation, the 4th order Rung-Kutta is used for time dimension and
three methods, finite difference, orthogonal collocation on finite
elements and Galerkin finite element are used for discretization of the
cell mass domain. The results indicate that the orthogonal collocation
on finite element not only is able to predict the oscillating behavior of
the cell culture but also needs much little time for calculations.
Therefore this method is preferred in comparison with other methods.
In the next step two controllers, a globally linearizing control (GLC)
and a conventional proportional-integral (PI) controller are designed
for controlling the total cell mass per unit volume, and performances
of these controllers are compared through simulation. The results
show that although the PI controller has simpler structure, the GLC
has better performance.
Abstract: The power transformer is the most expensive, indispensable and arguably the most important equipment item in a power system Insulation failure in transformers can cause long term interruption to supply and loss of revenue and the condition assessment of the insulation is thus an important maintenance procedure. Oil-impregnated transformer insulation consists of mainly organic materials including mineral oil and cellulose-base paper and pressboard. The operating life of cellulose-based insulation, as with most organic insulation, depends heavily on its operating temperature rise above ambient. This paper reports results of a laboratory-based experimental investigation of partial discharge (PD) activity at high temperature in oil-impregnated insulation. The experiments reported here are part an on-going programme aimed at investigating the way in which insulation deterioration can be monitored and quantified by use of partial discharge diagnostics. Partial discharge patterns were recorded and analysed during increasing and decreasing phases of the temperature. The effect of ageing of the insulation on the PD patterns in oil and oil-impregnated insulation are also considered.
Abstract: To maximise furnace production it-s necessary to
optimise furnace control, with the objectives of achieving maximum
power input into the melting process, minimum network distortion
and power-off time, without compromise on quality and safety. This
can be achieved with on the one hand by an appropriate electrode
control and on the other hand by a minimum of AC transformer
switching.
Electrical arc is a stochastic process; witch is the principal cause
of power quality problems, including voltages dips, harmonic
distortion, unbalance loads and flicker. So it is difficult to make an
appropriate model for an Electrical Arc Furnace (EAF). The factors
that effect EAF operation are the melting or refining materials,
melting stage, electrode position (arc length), electrode arm control
and short circuit power of the feeder. So arc voltages, current and
power are defined as a nonlinear function of the arc length. In this
article we propose our own empirical function of the EAF and model,
for the mean stages of the melting process, thanks to the
measurements in the steel factory.
Abstract: Bone growth factors, such as Bone Morphogenic
Protein-2 (BMP-2) have been approved by the FDA to replace grafting for some surgical interventions, but the high dose requirement limits its use in patients. Noggin, an extracellular protein, blocks the effect of BMP-2 by binding to BMP. Preventing
the BMP-2/noggin interaction will help increase the free
concentration of BMP-2 and therefore should enhance its efficacy to
induce bone formation. The work presented here involves
computational design of novel small molecule inhibitory agents of BMP-2/noggin interaction, based on our current understanding of
BMP-2, and its known putative ligands (receptors and antagonists). A
successful acquisition of such an inhibitory agent of BMP-2/noggin interaction would allow clinicians to reduce the dose required of
BMP-2 protein in clinical applications to promote osteogenesis. The
available crystal structures of the BMPs, its receptors, and the binding partner noggin were analyzed to identify the critical residues
involved in their interaction. In presenting this study, LUDI de novo design method was utilized to perform virtual screening of a large
number of compounds from a commercially available library against the binding sites of noggin to identify the lead chemical compounds
that could potentially block BMP-noggin interaction with a high specificity.
Abstract: Environmental impact assessment (EIA) is a procedure tool of environmental management for identifying, predicting, evaluating and mitigating the adverse effects of development proposals. EIA reports usually analyze how the amounts or concentrations of pollutants obey the relevant standards. Actually, many analytical tools can deepen the analysis of environmental impacts in EIA reports, such as life cycle assessment (LCA) and environmental risk assessment (ERA). Life cycle impact assessment (LCIA) is one of steps in LCA to introduce the causal relationships among environmental hazards and damage. Incorporating the LCIA concept into ERA as an integrated tool for EIA can extend the focus of the regulatory compliance of environmental impacts to determine of the significance of environmental impacts. Sometimes, when using integrated tools, it is necessary to consider fuzzy situations due to insufficient information; therefore, ERA should be generalized to fuzzy risk assessment (FRA). Finally, the use of the proposed methodology is demonstrated through the study case of the expansion plan of the world-s largest plastics processing factory.
Abstract: The range of the output power is a very important and evident limitation of two-level inverters. In order to overcome this disadvantage, multilevel inverters are introduced. Recently, Cascade H-Bridge inverters have emerged as one of the popular converter topologies used in numerous industrial applications. The modulation switching strategies such as phase shifted carrier based Pulse Width Modulation (PWM) technique and Stair case modulation with Selective Harmonic Elimination (SHE) PWM technique are generally used. NR method is used to solve highly non linear transcendental equations which are formed by SHEPWM method. Generally NR method has a drawback of requiring good initial guess but in this paper a new approach is implemented for NR method with any random initial guess. A three phase CHB 11-level inverter is chosen for analysis. MATLAB/SIMULINK programming environment and harmonic profiles are compared. Finally this paper presents a method at fundamental switching frequency with least % THDV.
Abstract: In the paper the research of flat textile products for use
as electrodes was presented. Material-s resistance measurements were
carried out to determine the suitability of the textiles. Based on the received results of studies different types of textile electrodes were
designed. Textile electrodes tests were carried out on human
phantoms. The electro-conductive properties of human forearm
phantom were also described. Based on this results special electroconductive
hydrogels with electro-conductive particles were feasible. The hydrogel is an important element of the forearm-s phantom
model of a survey of electrodes for muscle electrostimulation. The
hydrogel is an equivalent human skin and tissue. The hydrogel should
have a permanence and recurrence of the electro-conductive properties.
Abstract: In this study, in order to clarify wind-induced
phenomena, especially vertical mixing of density stratification in a
closed water area with floating-leaved plants, we conducted hydraulic
experiments on wind flow characteristics, wind wave characteristics,
entrainment phenomena and turbulent structure by using a wind tunnel
test tank and simulated floating-leaved plants. From the experimental
results of wind flow and wind wave characteristics, we quantified the
impact of the occupancy rate of the plants on their resistance
characteristics. From the experimental results of entrainment
phenomena, we defined the parameter that could explain the
magnitude of mixing between the density stratifications, and
quantified the impact of the occupancy rate on vertical mixing
between stratifications. From the experimental results of the turbulent
structure of the upper layer, we clarified the differences in small-scale
turbulence components at each occupancy rate and quantified the
impact of the occupancy rate on the turbulence characteristics. For a
summary of this study, we theoretically quantified wind-induced
entrainment phenomena in a closed water area with luxuriant growth
of floating-leaved plants. The results indicated that the impact of
luxuriant growth of floating-leaved plants in a closed water body
could be seen in the difference in small-scale fluid characteristics, and
these characteristics could be expressed using the small-scale
turbulent components.
Abstract: A power cable is widely used for power supply in
power distributing networks and power transmission lines. Due to
limitations in the production, delivery and setting up power cables,
they are produced and delivered in several separate lengths. Cable
itself, consists of two cable terminations and arbitrary number of
cable joints, depending on the cable route length. Electrical stress
control is needed to prevent a dielectric breakdown at the end of the
insulation shield in both the air and cable insulation. Reliability of
cable joint depends on its materials, design, installation and operating
environment. The paper describes design and performance results for
new modeled cable joints. Design concepts, based on numerical
calculations, must be correct. An Equivalent Electrodes
Method/Boundary Elements Method-hybrid approach that allows
electromagnetic field calculations in multilayer dielectric media,
including inhomogeneous regions, is presented.
Abstract: Biodiesel production results in glycerol production as
the main by-product in biodiesel industry.One of the utilizations of
glycerol obtained from biodiesel production is as a cement grinding
aid (CGA). Results showed that crude glycerol content was 40.19%
whereas pure glycerol content was 82.15%. BSS value of the cement
with CGA supplementation was higher than that of nonsupplemented
cement (blank) indicating that CGA-supplemented
cement had higher fineness than the non-supplemented one. It was
also found that pure glycerol 95% and TEA 5% at 80ºC was the
optimum CGA used to result in finest cement with BSS value of
4.836 cm2/g. Residue test showed that the smallest percent residue
value (0.11%) was obtained in cement with supplementation of pure
glycerol 95% and TEA 5%. Results of residue test confirmed those of
BSS test showing that cement with supplementation of pure glycerol
95% and TEA 5% had the finest particle size.
Abstract: An attempt has been made several times to identify
and discuss the U.S. experience on the formation of political nation in
political science. The purpose of this research paper is to identify the
main aspects of the formation of civic identity in the United States
and Kazakhstan, through the identification of similarities and
differences that can get practical application in making decisions of
national policy issues in the context of globalization, as well as to
answer the questions “What should unite the citizens of Kazakhstan
to the nation?" and “What should be the dominant identity: civil or
ethnic (national) one?"
Can Kazakhstan being multiethnic country like America, adopt its
experience in the formation of a civic nation? Since it is believed that
the “multi-ethnic state of the population is a characteristic feature of
most modern countries in the world," it states that “inter-ethnic
integration is one of the most important aspects of the problem of
forming a new social community (metaetnic - Kazakh people,
Kazakh nation" [1].
Abstract: Islam has a general principle of increase in
population. But the Muslims are equally obliged to take care of
health, education and the provisions etc. for their offspring and wives
in the best possible way. The Muslims would have to regulate and
manage the number of children, if any situation affects their duties
regarding their wives or children. Islam accomplishes permissibility
of temporary blockade in human fertility if someone faces any
problem regarding health of mother or children. During the life of the
Holy Prophet (SAW), Azl (coitus interruptus) was the only way for
temporary spacing between the children. In technologically
developed environment, the same can be resort through some
advanced methodology or instrument of temporary blockade. Solid
grounds are available in Islam that the fertility rate should be
managed if any of the aspect of human quality is being affected.
Abstract: Increase in using internet makes some problems that
one of them is "internet anxiety". Internet anxiety is a type of anxious
that people may feel during surfing internet or using internet for their
educational purpose, blogging or streaming to digital libraries. The
goal of this study is evaluating of internet anxiety among the
management students. In this research Ealy's internet anxiety
questionnaire, consists of positive and negative items, is completed
by 310 participants. According to the findings, about 64.7% of them
were equal or below to mean anxiety score (50). The distribution of
internet anxiety scores was normal and there was no meaningful
difference between men-s and women's anxiety level in this sample.
Results also showed that there is no meaningful difference of internet
anxiety level between different fields of study in Management. This
evaluation will help managers to perform gap analysis between the
existent level and the desired one. Future work would be providing
techniques for abating human anxiety while using internet via human
computer interaction techniques.
Abstract: One of the important factors of cracks on the asphalt
pavements is bitumen aging that associated with the loss of volatile
components and oxidation of asphalt binder. This paper is about
effect of Styrene-Butadiene-Styrene (SBS) polymer on asphalt aging
In order to decrease asphalt aging effects. For this purpose samples of
base bitumen and SBS modified bitumen aged according to the
rolling thin film oven test (RTFOT) and pressure aging vessel (PAV),
respectively. Properties of each sample were evaluated using Fourier
Transform Infrared (FTIR) spectroscopy, n-heptane precipitation,
viscosity test, softening point test and penetration test. FT-IR
Analysis, showed lower oxidation of SBS modified bitumen than
base bitumen, after aging.
Abstract: To measure the thickness of the subcutaneous adipose
tissue layer, a non-invasive optical measurement system (λ=1300 nm)
is introduced. Animal and human subjects are used for the
experiments. The results of human subjects are compared with the data
of ultrasound device measurements, and a high correlation (r=0.94 for
n=11) is observed. There are two modes in the corresponding signals
measured by the optical system, which can be explained by
two-layered and three-layered tissue models. If the target tissue is
thinner than the critical thickness, detected data using diffuse
reflectance method follow the three-layered tissue model, so the data
increase as the thickness increases. On the other hand, if the target
tissue is thicker than the critical thickness, the data follow the
two-layered tissue model, so they decrease as the thickness increases.
Abstract: A high performance clarification system has been
discussed for advanced aqueous reprocessing of FBR spent fuel.
Dissolver residue gives the cause of troubles on the plant operation of
reprocessing. In this study, the new clarification system based on the
hybrid of centrifuge and filtration was proposed to get the high
separation ability of the component of whole insoluble sludge. The
clarification tests of simulated solid species were carried out to
evaluate the clarification performance using small-scale test apparatus
of centrifuge and filter unit. The density effect of solid species on the
collection efficiency was mainly evaluated in the centrifugal
clarification test. In the filtration test using ceramic filter with pore
size of 0.2μm, on the other hand, permeability and filtration rate
were evaluated in addition to the filtration efficiency. As results, it was
evaluated that the collection efficiency of solid species on the new
clarification system was estimated as nearly 100%. In conclusion, the
high clarification performance of dissolver liquor can be achieved by
the hybrid of the centrifuge and filtration system.
Abstract: Today modern simulations solutions in the wind turbine industry have achieved a high degree of complexity and detail in result. Limitations exist when it is time to validate model results against measurements. Regarding Model validation it is of special interest to identify mode frequencies and to differentiate them from the different excitations. A wind turbine is a complex device and measurements regarding any part of the assembly show a lot of noise. Input excitations are difficult or even impossible to measure due to the stochastic nature of the environment. Traditional techniques for frequency analysis or features extraction are widely used to analyze wind turbine sensor signals, but have several limitations specially attending to non stationary signals (Events). A new technique based on autoregresive analysis techniques is introduced here for a specific application, a comparison and examples related to different events in the wind turbine operations are presented.
Abstract: The purpose of this paper is to provide an overview on methodological aspects of the information technology outsourcing (ITO) surveys, in an attempt to improve the data quality and reporting in survey research. It is based on a review of thirty articles on ITO surveys and focuses on two commonly explored dimensions of ITO, namely what are outsourced and why should there be ITO. This study highlights weaknesses in ITO surveys including lack of a clear definition of population, lack of information regarding the sampling method used, not citing the response rate, no information pertaining to pilot testing of survey instrument and absence of information on internal validity in the use or reporting of surveys. This study represents an attempt with a limited scope to point to shortfalls in the use survey methodology in ITO, and thus raise awareness among researchers in enhancing the reliability of survey findings.
Abstract: Reasonably priced and well-constructed housing must
be an integral and element supporting a healthy society. The absence
of housing everyone in society can afford negatively affects the
people's health, education, ability to get jobs, develop their
community. Without access to decent housing, economic
development, integration of immigrants and inclusiveness, the society
is negatively impacted. Canada has a sterling record in creating
housing compared to many other nations around the globe. Canadian
housing gets support from a mature and responsive mortgage network
and a top-quality construction industry as well as safe and excellent
quality building materials that are readily available. Yet 1.7 million
Canadian households occupy substandard abodes. During the past
hundred years, Canada's government has made a wide variety of
attempts to provide decent residential facilities every Canadian can
afford. Despite these laudable efforts, today Canada is left with
housing that is inadequate for many Canadians. People who own their
housing are given all kinds of privileges and perks, while people with
relatively low incomes who rent their apartments or houses are
discriminated against.
To help solve these problems, zoning that is based on an
"inclusionary" philosophy is tool developed to help provide people
the affordable residences that they need. No, thirty years after its
introduction, this type of zoning has been shown effective in helping
build and provide Canadians with a houses or apartments they can
afford to pay for. Using this form of zoning can have different results
+depending on where and how it is used. After examining Canadian
affordable housing and four American cases where this type of
zoning was enforced in the USA, this makes various
recommendations for expanding Canadians' access to housing they
can afford.