Abstract: FMEA has been used for several years and proved its efficiency for system’s risk analysis due to failures. Risk priority number found in FMEA is used to rank failure modes that may occur in a system. There are some guidelines in the literature to assign the values of FMEA components known as Severity, Occurrence and Detection. This paper propose a method to assign the value for occurrence in more realistic manner representing the state of the system under study rather than depending totally on the experience of the analyst. This method uses the hazard function of a system to determine the value of occurrence depending on the behavior of the hazard being constant, increasing or decreasing.
Abstract: This paper presents a regression model with
autocorrelated errors in which the inputs are social moods obtained by
analyzing the adjectives in Twitter posts using a document topic
model, where document topics are extracted using LDA. The
regression model predicts Dow Jones Industrial Average (DJIA) more
precisely than autoregressive moving-average models.
Abstract: This paper presents the application of finite dynamic
programming, specifically the "Markov Chain" model, as part of the
decision making process of a company in the cosmetics sector located
in the vicinity of Bogota DC. The objective of this process was to
decide whether the company should completely reconstruct its
wastewater treatment plant or instead optimize the plant through the
addition of equipment. The goal of both of these options was to make
the required improvements in order to comply with parameters
established by national legislation regarding the treatment of waste
before it is released into the environment. This technique will allow
the company to select the best option and implement a solution for
the processing of waste to minimize environmental damage and the
acquisition and implementation costs.
Abstract: Disasters are quite experienced in our days. They are
caused by floods, landslides, and building fires that is the main
objective of this study. To cope with these unexpected events,
precautions must be taken to protect human lives. The emphasis on
disposal work focuses on the resolution of the evacuation problem in
case of no-notice disaster. The problem of evacuation is listed as a
dynamic network flow problem. Particularly, we model the
evacuation problem as an earliest arrival flow problem with load
dependent transit time. This problem is classified as NP-Hard. Our
challenge here is to propose a metaheuristic solution for solving the
evacuation problem. We define our objective as the maximization of
evacuees during earliest periods of a time horizon T. The objective
provides the evacuation of persons as soon as possible. We
performed an experimental study on emergency evacuation from the
tunisian children’s hospital. This work prompts us to look for
evacuation plans corresponding to several situations where the
network dynamically changes.
Abstract: Bureaucracy reform program drives Indonesian
government to change their management to enhance their
organizational performance. Information technology became one of
strategic plan that organization tried to improve. Knowledge
management system is one of information system that supporting
knowledge management implementation in government which
categorized as people perspective, because this system has high
dependency in human interaction and participation. Strategic plan for
developing knowledge management system can be determine using
some of information system strategic methods. This research
conducted to define type of strategic method of information system,
stage of activity each method, strength and weakness. Literature
review methods used to identify and classify strategic methods of
information system, differentiate method type, categorize common
activities, strength and weakness. Result of this research are
determine and compare six strategic information system methods,
Balanced Scorecard and Risk Analysis believe as common strategic
method that usually used and have the highest excellence strength.
Abstract: High temperature deformation behavior of cast
Fe-20Cr-5Al alloy has been investigated in this study by performing
tensile and compression tests at temperatures from 1100 to 1200oC.
Rectangular ingots of which the dimensions were 300×300×100 in
millimeter were cast using vacuum induction melting. Phase
equilibrium was calculated using the FactSage®, thermodynamic
software and database. Tensile strength of cast Fe-20Cr-5Al alloy was
4 MPa at 1200oC. With temperature decreased, tensile strength
increased rapidly and reached up to 13 MPa at 1100oC. Elongation
also increased from 18 to 80% with temperature decreased from
1200oC to 1100oC. Microstructure observation revealed that M23C6
carbide was precipitated along the grain boundary and within the
matrix.
Abstract: Phase equilibria of AZ91D Mg alloys for
nonflammable use, containing Ca and Y, were carried out by using
FactSage® and FTLite database, which revealed that solid solution
treatment could be performed at temperatures from 400 to 450oC.
Solid solution treatment of AZ91D Mg alloy without Ca and Y was
successfully conducted at 420oC and supersaturated microstructure
with all beta phase resolved into matrix was obtained. In the case of
AZ91D Mg alloy with some Ca and Y; however, a little amount of
intermetallic particles were observed after solid solution treatment.
After solid solution treatment, each alloy was annealed at temperatures
of 180 and 200oC for time intervals from 1 min to 48 hrs and hardness
of each condition was measured by micro-Vickers method. Peak aging
conditions were deduced as at the temperature of 200oC for 10 hrs.
Abstract: In the present study, M2 high speed steels were
fabricated by using electro-slag rapid remelting process. Carbide
structure was analysed and the fracture toughness and hardness were
also measured after austenitization treatment at 1190 and 1210oC
followed by tempering treatment at 535oC for billets with various
diameters from 16 to 60 mm. Electro-slag rapid remelting (ESRR)
process is an advanced ESR process combined by continuous casting
and successfully employed in this study to fabricate a sound M2 high
speed ingot. Three other kinds of commercial M2 high speed steels,
produced by traditional method, were also analysed for comparison.
Distribution and structure of eutectic carbides of the ESRR billet were
found to be comparable to those of commercial alloy and so was the
fracture toughness.
Abstract: One of the major goals of Spoken Dialog Systems
(SDS) is to understand what the user utters.
In the SDS domain, the Spoken Language Understanding (SLU)
Module classifies user utterances by means of a pre-definite
conceptual knowledge. The SLU module is able to recognize only the
meaning previously included in its knowledge base. Due the vastity
of that knowledge, the information storing is a very expensive
process.
Updating and managing the knowledge base are time-consuming
and error-prone processes because of the rapidly growing number of
entities like proper nouns and domain-specific nouns. This paper
proposes a solution to the problem of Name Entity Recognition
(NER) applied to a SDS domain. The proposed solution attempts to
automatically recognize the meaning associated with an utterance by
using the PANKOW (Pattern based Annotation through Knowledge
On the Web) method at runtime.
The method being proposed extracts information from the Web to
increase the SLU knowledge module and reduces the development
effort. In particular, the Google Search Engine is used to extract
information from the Facebook social network.
Abstract: In addition to the production, which is already
frequently optimized, improving the distribution logistics also opens
up tremendous potential for increasing an enterprise’s
competitiveness. Here too though, numerous interactions need to be
taken into account, enterprises thus need to be able to identify and
weigh between different potentials for economically efficient
optimizations. In order to be able to assess potentials, enterprises
require a suitable method. This paper first briefly presents the need
for this research before introducing the procedure that will be used to
develop an appropriate method that not only considers interactions
but is also quickly and easily implemented.
Abstract: Nowadays, the amounts of companies which tend to
have an Enterprise Resource Planning (ERP) application are
increasing. Although ERP projects are expensive, time consuming,
and complex, there are some successful experiences. These days,
developing countries are striving to implement ERP projects
successfully; however, there are many obstacles. Therefore, these
projects would be failed or partially failed. This paper concerns the
implementation of a successful ERP implementation, IFS, in Iran at
Dana Geophysics Company (DGC). After a short review of ERP and
ERP market in Iran, we propose a three phases deployment
methodology (phase 1: Preparation and Business Process
Management (BPM) phase 2: implementation and phase 3: testing,
golive-1 (pilot) and golive-2 (final)). Then, we present five guidelines
(Project Management, Change Management, Business Process
Management (BPM), Training& Knowledge Management, and
Technical Management), which were chose as work streams. In this
case study we present lessons learned in Project management and
Business process Management.
Abstract: The article demonstrates on a case study how it is
possible to identify MSD risk. It is based on a dissertation Risk
identification model of occupational diseases formation in relation to
the work activity that determines what risk can endanger workers who
are exposed to the specific risk factors. It is evaluated based on
statistical calculations. These risk factors are main cause of upperextremities
musculoskeletal disorders.
Abstract: This paper presents an anthropometric study
conducted to 300 employees in a maquiladora industry that belongs
to the cluster of medical products as part of a research project to
pretend simulate workplace conditions under which operators
conduct their activities. This project is relevant because traditionally
performed a study to design ergonomic workspaces according to
anthropometric profile of users, however, this paper demonstrates the
importance of making decisions when the infrastructure cannot be
adapted for economic whichever put emphasis on user activity.
Abstract: Caused by shorter product life cycles and higher
product variety the importance of production ramp ups is increasing.
Even though companies are aware of that fact, up to 40% of the ramp
up projects still miss technical and economical requirements. The
success of a ramp up depends on the planning of human factors,
organizational aspects and technological solutions. Since only partly
considered in scientific literature, this paper lays its focus on the
human factor during production ramp up. There are only incoherent
methods which address the problems in this area. A systematic and
holistic method to improve the capabilities of the employees during
ramp up is missing. The Harada Method is a relatively young
approach for developing highly-skilled workers. It consists of
different worksheets which help employees to set guidelines and
reach overall objectives. This approach is going to be transferred into
a tool for ramp up management.
Abstract: In this paper, we present a comparative assessment of
Space Vector Pulse Width Modulation (SVPWM) and Model
Predictive Control (MPC) for two-level three phase (2L-3P) Voltage
Source Inverter (VSI). VSI with associated system is subjected to
both control techniques and the results are compared.
Matlab/Simulink was used to model, simulate and validate the
control schemes. Findings of this study show that MPC is superior to
SVPWM in terms of total harmonic distortion (THD) and
implementation.
Abstract: The research focus on study, analyze and design the
model of the infrastructure and computer networks for distance
education, online learning via new media, e-learning and blended
learning. The collected information from study and analyze process
that information was evaluated by the index of item objective
congruence (IOC) by 9 specialists to design model. The results of
evaluate the model with the mean and standard deviation by the
sample of 9 specialists value is 3.85. The results showed that the
infrastructure and computer networks are designed to be appropriate
to a great extent appropriate to a great extent.
Abstract: The goal of this article is the analysis of knowledge
transfer at the regional level of the Czech Republic. We show how
goals of enterprises´ innovative activities are related to the rate of
cooperation with different actors within regional innovative systems
as well as in other world regions. The results show that the most
important partners of enterprises are their suppliers and clients in
most Czech regions. The cooperation rate of enterprises correlates
significantly mainly with enterprises´ efforts to enter new markets
and reduce labour costs per unit output. The meaning of this
cooperation decreases with the increase of partner’s distance.
Regarding the type of a cooperating partner, cooperation within an
enterprise had to do with the increase of market share and decrease of
labour costs. On the other hand, cooperation with clients had to do
with efforts to replace outdated products or processes or enter new
markets. We can pay less attention to the cooperation with
government authorities and organizations. The reasons for
marginalization of this cooperation should be submitted to further
detailed investigation.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: The purpose of this project is to carry out an analysis
and determine the profile of actual lean manufacturing processes in
the Metropolitan Area of Bucaramanga. Through the analysis of
qualitative and quantitative variables it was possible to establish how
these manufacturers develop production practices that ensure their
competitiveness and productivity in the market.
In this study, a random sample of metallurgic and wrought iron
companies was applied, following which a quantitative focus and
analysis was used to formulate a qualitative methodology for
measuring the level of lean manufacturing procedures in the industry.
A qualitative evaluation was also carried out through a multivariate
analysis using the Numerical Taxonomy System (NTSYS) program
which should allow for the determination of Lean Manufacturing
profiles.
Through the results it was possible to observe how the companies
in the sector are doing with respect to Lean Manufacturing Practices,
as well as identify the level of management that these companies
practice with respect to this topic. In addition, it was possible to
ascertain that there is no one dominant profile in the sector when it
comes to Lean Manufacturing.
It was established that the companies in the metallurgic and
wrought iron industry show low levels of Lean Manufacturing
implementation. Each one carries out diverse actions that are
insufficient to consolidate a sectoral strategy for developing a
competitive advantage which enables them to tie together a
production strategy.
Abstract: In today’s world, the LED display has been used for
presenting visual information under various circumstances. Such
information is an important intermediary in the human information
processing. Researchers have been investigated diverse factors that
influence this process effectiveness. The letter size is undoubtedly
one major factor that has been tested and recommended by many
standards and guidelines. However, viewing information on the
display from direct perpendicular position is a typical assumption
whereas many actual events are required viewing from the angles.
This current research aims to study the effect of oblique viewing
angle and viewing distance on ability to recognize alphabet, number,
and English word. The total of ten participants was volunteered to our
3 x 4 x 4 within subject study. Independent variables include three
distance levels (2, 6, and 12 m), four oblique angles (0, 45, 60, 75
degree), and four target types (alphabet, number, short word, and
long word). Following the method of constant stimuli our study
suggests that the larger oblique angle, ranging from 0 to 75 degree
from the line of sight, results in significant higher legibility threshold
or larger font size required (p-value < 0.05). Viewing distance factor
also shows to have significant effect on the threshold (p-value