Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.
Abstract: The threshold voltage and capacitance voltage characteristics of ultra-thin Silicon-on-Insulator MOSFET are greatly influenced by the thickness and doping concentration of the silicon film. In this work, the capacitance voltage characteristics and threshold voltage of the device have been analyzed with quantum mechanical effects using the Self-Consistent model. Reduction of channel thickness and adding doping impurities cause an increase in the threshold voltage. Moreover, the temperature effects cause a significant amount of threshold voltage shift. The temperature dependence of threshold voltage has also been observed with Self- Consistent approach which are well supported from experimental performance of practical devices.
Abstract: In this paper, a generalized synchronization scheme, which is called function synchronization, for chaotic systems is studied. Based on Lyapunov method and active control method, we design the synchronization controller for the system such that the error dynamics between master and slave chaotic systems is asymptotically stable. For verification of our theory, computer and circuit simulations for a specific chaotic system is conducted.
Abstract: Khao Yai National Park is the First National Park in
Thailand and approximately 800,000 tourists visited Khao Yai yearly.
This study aimed to identify the perception of tourists in Khao Yai
National Park according to the implementation of eco-friendly
cleansers along their leisure in the campsites. Due to tourist’s
activities in the park were affected on quality of environment;
especially on water resource. Therefore, eco-friendly cleansers were
used in campsites for tourists and restaurants during high tourist
season. The results indicated positive effects of environmental
friendly cleansers on water quality in Lam Ta Khong River, as well
as the tourist’s perception on eco-friendly cleansers.
Abstract: The technical realization of data transmission using
glass fiber began after the development of diode laser in year 1962.
The erbium doped fiber amplifiers (EDFA's) in high speed networks
allow information to be transmitted over longer distances without
using of signal amplification repeaters. These kinds of fibers are
doped with erbium atoms which have energy levels in its atomic
structure for amplifying light at 1550nm. When a carried signal wave
at 1550nm enters the erbium fiber, the light stimulates the excited
erbium atoms which pumped with laser beam at 980nm as additional
light. The wavelength and intensity of the semiconductor lasers
depend on the temperature of active zone and the injection current.
The present paper shows the effect of the diode lasers temperature
and injection current on the optical amplification. From the results of
in- and output power one may calculate the max. optical gain by
erbium doped fiber amplifier.
Abstract: As a result of urbanization, the unpredictable growth of industry and transport, production of chemicals, military activities, etc. the concentration of anthropogenic toxicants spread in nature exceeds all the permissible standards. Most dangerous among these contaminants are organic compounds having great persistence, bioaccumulation, and toxicity along with our awareness of their prominent occurrence in the environment and food chain. Among natural ecological tools, plants still occupying above 40% of the world land, until recently, were considered as organisms having only a limited ecological potential, accumulating in plant biomass and partially volatilizing contaminants of different structure. However, analysis of experimental data of the last two decades revealed the essential role of plants in environment remediation due to ability to carry out intracellular degradation processes leading to partial or complete decomposition of carbon skeleton of different structure contaminants. Though, phytoremediation technologies still are in research and development, their various applications have been successfully used. The paper aims to analyze mechanisms of organic contaminants uptake and detoxification in plants, being the less studied issue in evaluation and exploration of plants potential for environment remediation.
Abstract: The objective of the present study was to evaluate the
potential of hollow microneedles for enhancing the transdermal
delivery of Bovine Serum Albumin (MW~66,000 Da)-Fluorescein
Isothiocyanate (BSA-FITC) conjugate, a hydrophilic large molecular
compound. Moreover, the effect of different formulations was
evaluated. The series of binary mixtures composed of propylene
glycol (PG) and pH 7.4 phosphate buffer solution (PBS) was
prepared and used as a medium for BSA-FITC. The results showed
that there was no permeation of BSA-FITC solution across the
neonatal porcine skin without using hollow microneedles, whereas
the cumulative amount of BSA-FITC released at 8 h through the
neonatal porcine skin was about 60-70% when using hollow
microneedles. Furthermore, the results demonstrated that the higher
volume of PG in binary mixtures injected, the lower cumulative
amount of BSA-FITC released and release rate of BSA-FITC from
skin. These release profiles of BSA-FITC in binary mixtures were
expressed by Fick-s law of diffusion. These results suggest the
utilization of hollow microneedle to enhance transdermal delivery of
protein and provide useful information for designing an effective
hollow microneedle system.
Abstract: Influence of octane and benzene on plant cell
ultrastructure and enzymes of basic metabolism, such as nitrogen
assimilation and energy generation have been studied. Different
plants: perennial ryegrass (Lolium perenne) and alfalfa (Medicago
sativa); crops- maize (Zea mays L.) and bean (Phaseolus vulgaris);
shrubs – privet (Ligustrum sempervirens) and trifoliate orange
(Poncirus trifoliate); trees - poplar (Populus deltoides) and white
mulberry (Morus alba L.) were exposed to hydrocarbons of different
concentrations (1, 10 and 100 mM). Destructive changes in bean and
maize leaves cells ultrastructure under the influence of benzene
vapour were revealed at the level of photosynthetic and energy
generation subcellular organells. Different deviations at the level of
subcellular organelles structure and distribution were observed in
alfalfa and ryegrass root cells under the influence of benzene and
octane, absorbed through roots. The level of destructive changes is
concentration dependent. Benzene at low 1 and 10 mM concentration
caused the increase in glutamate dehydrogenase (GDH) activity in
maize roots and leaves and in poplar and mulberry shoots, though to
higher extent in case of lower, 1mM concentration. The induction
was more intensive in plant roots. The highest tested 100mM
concentration of benzene was inhibitory to the enzyme in all plants.
Octane caused induction of GDH in all grassy plants at all tested
concentrations; however the rate of induction decreased parallel to
increase of the hydrocarbon concentration. Octane at concentration 1
mM caused induction of GDH in privet, trifoliate and white mulberry
shoots. The highest, 100mM octane was characterized by inhibitory
effect to GDH activity in all plants. Octane had inductive effect on
malate dehydrogenase in almost all plants and tested concentrations,
indicating the intensification of Trycarboxylic Acid Cycle.
The data could be suggested for elaboration of criteria for plant
selection for phytoremediation of oil hydrocarbons contaminated
soils.
Abstract: Understanding the cell's large-scale organization is an
interesting task in computational biology. Thus, protein-protein
interactions can reveal important organization and function of the
cell. Here, we investigated the correspondence between protein
interactions and function for the yeast. We obtained the correlations
among the set of proteins. Then these correlations are clustered using
both the hierarchical and biclustering methods. The detailed analyses
of proteins in each cluster were carried out by making use of their
functional annotations. As a result, we found that some functional
classes appear together in almost all biclusters. On the other hand, in
hierarchical clustering, the dominancy of one functional class is
observed. In brief, from interaction data to function, some correlated
results are noticed about the relationship between interaction and
function which might give clues about the organization of the
proteins.
Abstract: With Power system movement toward restructuring along with factors such as life environment pollution, problems of transmission expansion and with advancement in construction technology of small generation units, it is expected that small units like wind turbines, fuel cells, photovoltaic, ... that most of the time connect to the distribution networks play a very essential role in electric power industry. With increase in developing usage of small generation units, management of distribution networks should be reviewed. The target of this paper is to present a new method for optimal management of active and reactive power in distribution networks with regard to costs pertaining to various types of dispersed generations, capacitors and cost of electric energy achieved from network. In other words, in this method it-s endeavored to select optimal sources of active and reactive power generation and controlling equipments such as dispersed generations, capacitors, under load tapchanger transformers and substations in a way that firstly costs in relation to them are minimized and secondly technical and physical constraints are regarded. Because the optimal management of distribution networks is an optimization problem with continuous and discrete variables, the new evolutionary method based on Ant Colony Algorithm has been applied. The simulation results of the method tested on two cases containing 23 and 34 buses exist and will be shown at later sections.
Abstract: Migration in breast cancer cell wound healing assay
had been studied using image fractal dimension analysis. The
migration of MDA-MB-231 cells (highly motile) in a wound healing
assay was captured using time-lapse phase contrast video microscopy
and compared to MDA-MB-468 cell migration (moderately motile).
The Higuchi fractal method was used to compute the fractal
dimension of the image intensity fluctuation along a single pixel
width region parallel to the wound. The near-wound region fractal
dimension was found to decrease three times faster in the MDA-MB-
231 cells initially as compared to the less cancerous MDA-MB-468
cells. The inner region fractal dimension was found to be fairly
constant for both cell types in time and suggests a wound influence
range of about 15 cell layer. The box-counting fractal dimension
method was also used to study region of interest (ROI). The MDAMB-
468 ROI area fractal dimension was found to decrease
continuously up to 7 hours. The MDA-MB-231 ROI area fractal
dimension was found to increase and is consistent with the behavior
of a HGF-treated MDA-MB-231 wound healing assay posted in the
public domain. A fractal dimension based capacity index has been
formulated to quantify the invasiveness of the MDA-MB-231 cells in
the perpendicular-to-wound direction. Our results suggest that image
intensity fluctuation fractal dimension analysis can be used as a tool
to quantify cell migration in terms of cancer severity and treatment
responses.
Abstract: A transient finite element model has been developed
to study the heat transfer and fluid flow during spot Gas Tungsten
Arc Welding (GTAW) on stainless steel. Temperature field, fluid
velocity and electromagnetic fields are computed inside the cathode,
arc-plasma and anode using a unified MHD formulation. The
developed model is then used to study the influence of different
helium-argon gas mixtures on both the energy transferred to the
workpiece and the time evolution of the weld pool dimensions. It is
found that the addition of helium to argon increases the heat flux
density on the weld axis by a factor that can reach 6.5. This induces
an increase in the weld pool depth by a factor of 3. It is also found
that the addition of only 10% of argon to helium decreases
considerably the weld pool depth, which is due to the electrical
conductivity of the mixture that increases significantly when argon is
added to helium.
Abstract: In very narrow pathways, the speed of sound propagation and the phase of sound waves change due to the air viscosity. We have developed a new finite element method (FEM) that includes the effects of air viscosity for modeling a narrow sound pathway. This method is developed as an extension of the existing FEM for porous sound-absorbing materials. The numerical calculation results for several three-dimensional slit models using the proposed FEM are validated against existing calculation methods.
Abstract: The knowledge base of welding defect recognition is
essentially incomplete. This characteristic determines that the recognition results do not reflect the actual situation. It also has a further influence on the classification of welding quality. This paper is
concerned with the study of a rough set based method to reduce the influence and improve the classification accuracy. At first, a rough set
model of welding quality intelligent classification has been built. Both condition and decision attributes have been specified. Later on, groups
of the representative multiple compound defects have been chosen
from the defect library and then classified correctly to form the
decision table. Finally, the redundant information of the decision table has been reducted and the optimal decision rules have been reached. By this method, we are able to reclassify the misclassified defects to
the right quality level. Compared with the ordinary ones, this method
has higher accuracy and better robustness.
Abstract: Cooktop burners are widely used nowadays. In
cooktop burner design, nozzle efficiency and greenhouse
gas(GHG) emissions mainly depend on heat transfer from the
premixed flame to the impinging surface. This is a complicated
issue depending on the individual and combined effects of various
input combustion variables. Optimal operating conditions for
sustainable burner design were rarely addressed, especially in the
case of multiple slot-jet burners. Through evaluating the optimal
combination of combustion conditions for a premixed slot-jet
array, this paper develops a practical approach for the sustainable
design of gas cooktop burners. Efficiency, CO and NOx emissions
in respect of an array of slot jets using premixed flames were
analysed. Response surface experimental design were applied to
three controllable factors of the combustion process, viz.
Reynolds number, equivalence ratio and jet-to-vessel distance.
Desirability Function Approach(DFA) is the analytic technique
used for the simultaneous optimization of the efficiency and
emission responses.
Abstract: In this paper, we propose the Modified Synchronous Detection (MSD) Method for determining the reference compensating currents of the shunt active power filter under non sinusoidal voltages conditions. For controlling the inverter switching we used the PI regulator. The numerical simulation results, using Power System Blockset Toolbox PSB of Matlab, from a complete structure, are presented and discussed.
Abstract: This paper proposed a nonlinear model predictive
control (MPC) method for the control of gantry crane. One of the main
motivations to apply MPC to control gantry crane is based on its
ability to handle control constraints for multivariable systems. A
pre-compensator is constructed to compensate the input nonlinearity
(nonsymmetric dead zone with saturation) by using its inverse
function. By well tuning the weighting function matrices, the control
system can properly compromise the control between crane position
and swing angle. The proposed control algorithm was implemented for
the control of gantry crane system in System Control Lab of University
of Technology, Sydney (UTS), and achieved desired experimental
results.
Abstract: The problem of complex use of water resources in
Central Asia by taking into consideration the sovereignty of the states
and increasing demand on use of water for economic aspects are
considered. Complex program with appropriate mathematical
software intended for calculation of possible variants of using the
Amudarya up-stream water resources according to satisfaction of
incompatible requirements of the national economics in irrigation
and energy generation is proposed.
Abstract: Scatter behavior of fatigue life in die-cast AM60B
alloy was investigated. For comparison, those in rolled AM60B alloy
and die-cast A365-T5 aluminum alloy were also studied. Scatter
behavior of pore size was also investigated to discuss dominant
factors for fatigue life scatter in die-cast materials. Three-parameter
Weibull function was suitable to explain the scatter behavior of both
fatigue life and pore size. The scatter of fatigue life in die-cast
AM60B alloy was almost comparable to that in die-cast A365-T5
alloy, while it was significantly large compared to that in the rolled
AM60B alloy. Scatter behavior of pore size observed at fracture
nucleation site on the fracture surface was comparable to that
observed on the specimen cross-section and also to that of fatigue
life. Therefore, the dominant factor for large scatter of fatigue life in
die-cast alloys would be the large scatter of pore size. This
speculation was confirmed by the fracture mechanics fatigue life
prediction, where the pore observed at fatigue crack nucleation site
was assumed as the pre-existing crack.
Abstract: The paper presents a part of the results obtained in a
complex research project on Romanian Grey Steppe breed, owner of
some remarkable qualities such as hardiness, longevity, adaptability,
special resistance to ban weather and diseases and included in the
genetic fund (G.D. no. 822/2008.) from Romania.
Following the researches effectuated, we identified alleles of six
loci, codifying the six types of major milk proteins: alpha-casein S1
(α S1-cz); beta-casein (β-cz); kappa-casein (K-cz); beta-lactoglobulin
(β-lg); alpha-lactalbumin (α-la) and alpha-casein S2 (α S2-cz). In
system αS1-cz allele αs1-Cn B has the highest frequency (0.700), in
system β-cz allele β-Cn A2 ( 0.550 ), in system K-cz allele k-CnA2 (
0.583 ) and heterozygote genotype AB ( 0.416 ) and BB (0.375), in
system β-lg allele β-lgA1 has the highest frequency (0.542 ) and
heterozygote genotype AB ( 0.500 ), in system α-la there is
monomorphism for allele α-la B and similarly in system αS2-cz for
allele αs2-Cn A.
The milk analysis by the isoelectric focalization technique (I.E.F.)
allowed the identification of a new allele for locus αS1-casein, for two
of the individuals under analysis, namely allele called αS1-casein
IRV. When experiments were repeated, we noticed that this is not a
proteolysis band and it really was a new allele that has not been
registered in the specialized literature so far. We identified two
heterozygote individuals, carriers of this allele, namely: BIRV and
CIRV. This discovery is extremely important if focus is laid on the
national genetic patrimony.