Abstract: The agriculture lignocellulosic by-products are receiving increased attention, namely in the search for filter materials that retain contaminants from water. These by-products, specifically almond and hazelnut shells are abundant in Portugal once almond and hazelnuts production is a local important activity. Hazelnut and almond shells have as main constituents lignin, cellulose and hemicelluloses, water soluble extractives and tannins. Along the adsorption of heavy metals from contaminated waters, water soluble compounds can leach from shells and have a negative impact in the environment. Usually, the chemical characterization of treated water by itself may not show environmental impact caused by the discharges when parameters obey to legal quality standards for water. Only biological systems can detect the toxic effects of the water constituents. Therefore, the evaluation of toxicity by biological tests is very important when deciding the suitability for safe water discharge or for irrigation applications.
The main purpose of the present work was to assess the potential impacts of waters after been treated for heavy metal removal by hazelnut and almond shells adsorption systems, with short term acute toxicity tests.
To conduct the study, water at pH 6 with 25 mg.L-1 of lead, was treated with 10 g of shell per litre of wastewater, for 24 hours. This procedure was followed for each bark. Afterwards the water was collected for toxicological assays; namely bacterial resistance, seed germination, Lemna minor L. test and plant grow. The effect in isolated bacteria strains was determined by disc diffusion method and the germination index of seed was evaluated using lettuce, with temperature and humidity germination control for 7 days. For aquatic higher organism, Lemnas were used with 4 days contact time with shell solutions, in controlled light and temperature. For terrestrial higher plants, biomass production was evaluated after 14 days of tomato germination had occurred in soil, with controlled humidity, light and temperature.
Toxicity tests of water treated with shells revealed in some extent effects in the tested organisms, with the test assays showing a close behaviour as the control, leading to the conclusion that its further utilization may not be considered to create a serious risk to the environment.
Abstract: With the development of ubiquitous computing,
current user interaction approaches with keyboard, mouse and pen
are not sufficient. Due to the limitation of these devices the useable
command set is also limited. Direct use of hands as an input device is
an attractive method for providing natural Human Computer
Interaction which has evolved from text-based interfaces through 2D
graphical-based interfaces, multimedia-supported interfaces, to fully
fledged multi-participant Virtual Environment (VE) systems.
Imagine the human-computer interaction of the future: A 3Dapplication
where you can move and rotate objects simply by moving
and rotating your hand - all without touching any input device. In this
paper a review of vision based hand gesture recognition is presented.
The existing approaches are categorized into 3D model based
approaches and appearance based approaches, highlighting their
advantages and shortcomings and identifying the open issues.
Abstract: In this paper, solution of fuzzy differential equation
under general differentiability is obtained by genetic programming
(GP). The obtained solution in this method is equivalent or very close
to the exact solution of the problem. Accuracy of the solution to this
problem is qualitatively better. An illustrative numerical example is
presented for the proposed method.
Abstract: Maximal Ratio Combining (MRC) is considered the most complex combining technique as it requires channel coefficients estimation. It results in the lowest bit error rate (BER) compared to all other combining techniques. However the BER starts to deteriorate as errors are introduced in the channel coefficients estimation. A novel combining technique, termed Generalized Maximal Ratio Combining (GMRC) with a polynomial kernel, yields an identical BER as MRC with perfect channel estimation and a lower BER in the presence of channel estimation errors. We show that GMRC outperforms the optimal MRC scheme in general and we hereinafter introduce it to the scientific community as a new “supraoptimal" algorithm. Since diversity combining is especially effective in small femto- and pico-cells, internet-associated wireless peripheral systems are to benefit most from GMRC. As a result, many spinoff applications can be made to IP-based 4th generation networks.
Abstract: The work presented in this paper focus on Knowledge Management services enabling CSCW (Computer Supported Cooperative Work) applications to provide an appropriate adaptation to the user and the situation in which the user is working. In this paper, we explain how a knowledge management system can be designed to support users in different situations exploiting contextual data, users' preferences, and profiles of involved artifacts (e.g., documents, multimedia files, mockups...). The presented work roots in the experience we had in the MILK project and early steps made in the MAIS project.
Abstract: Today, Genetic Algorithm has been used to solve
wide range of optimization problems. Some researches conduct on
applying Genetic Algorithm to text classification, summarization
and information retrieval system in text mining process. This
researches show a better performance due to the nature of Genetic
Algorithm. In this paper a new algorithm for using Genetic
Algorithm in concept weighting and topic identification, based on
concept standard deviation will be explored.
Abstract: Texture information plays increasingly an important
role in remotely sensed imagery classification and many pattern
recognition applications. However, the selection of relevant textural
features to improve this classification accuracy is not a straightforward
task. This work investigates the effectiveness of two Mutual
Information Feature Selector (MIFS) algorithms to select salient
textural features that contain highly discriminatory information for
multispectral imagery classification. The input candidate features are
extracted from a SPOT High Resolution Visible(HRV) image using
Wavelet Transform (WT) at levels (l = 1,2).
The experimental results show that the selected textural features
according to MIFS algorithms make the largest contribution to
improve the classification accuracy than classical approaches such
as Principal Components Analysis (PCA) and Linear Discriminant
Analysis (LDA).
Abstract: The study of proteomics reached unexpected levels of
interest, as a direct consequence of its discovered influence over some
complex biological phenomena, such as problematic diseases like
cancer. This paper presents the latest authors- achievements regarding
the analysis of the networks of proteins (interactome networks), by
computing more efficiently the betweenness centrality measure. The
paper introduces the concept of betweenness centrality, and then
describes how betweenness computation can help the interactome net-
work analysis. Current sequential implementations for the between-
ness computation do not perform satisfactory in terms of execution
times. The paper-s main contribution is centered towards introducing
a speedup technique for the betweenness computation, based on
modified shortest path algorithms for sparse graphs. Three optimized
generic algorithms for betweenness computation are described and
implemented, and their performance tested against real biological
data, which is part of the IntAct dataset.
Abstract: This paper presents strategies for dynamically creating, managing and removing mesh cells during computations in the context of the Material Point Method (MPM). The dynamic meshing approach has been developed to help address problems involving motion of a finite size body in unbounded domains in which the extent of material travel and deformation is unknown a priori, such as in the case of landslides and debris flows. The key idea is to efficiently instantiate and search only cells that contain material points, thereby avoiding unneeded storage and computation. Mechanisms for doing this efficiently are presented, and example problems are used to demonstrate the effectiveness of dynamic mesh management relative to alternative approaches.
Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: This paper presents the design, fabrication and
evaluation of magneto-rheological damper. Semi-active control
devices have received significant attention in recent years because
they offer the adaptability of active control devices without requiring
the associated large power sources. Magneto-Rheological (MR)
dampers are semi- active control devices that use MR fluids to
produce controllable dampers. They potentially offer highly reliable
operation and can be viewed as fail-safe in that they become passive
dampers if the control hardware malfunction. The advantage of MR
dampers over conventional dampers are that they are simple in
construction, compromise between high frequency isolation and
natural frequency isolation, they offer semi-active control, use very
little power, have very quick response, has few moving parts, have a
relax tolerances and direct interfacing with electronics. Magneto-
Rheological (MR) fluids are Controllable fluids belonging to the
class of active materials that have the unique ability to change
dynamic yield stress when acted upon by an electric or magnetic
field, while maintaining viscosity relatively constant. This property
can be utilized in MR damper where the damping force is changed by
changing the rheological properties of the fluid magnetically. MR
fluids have a dynamic yield stress over Electro-Rheological fluids
(ER) and a broader operational temperature range. The objective of
this papert was to study the application of an MR damper to vibration
control, design the vibration damper using MR fluids, test and
evaluate its performance. In this paper the Rheology and the theory
behind MR fluids and their use on vibration control were studied.
Then a MR vibration damper suitable for vehicle suspension was
designed and fabricated using the MR fluid. The MR damper was
tested using a dynamic test rig and the results were obtained in the
form of force vs velocity and the force vs displacement plots. The
results were encouraging and greatly inspire further research on the
topic.
Abstract: Nowadays, without the awareness of consumer
behavior and correct understanding of it, it is not possible for organizations to take appropriate measures to meet the consumer
needs and demands. The aim of this paper is the identification and
prioritization of the factors affecting the consumer behavior based on
the product value. The population of the study includes all the
consumers of furniture producing firms in East Azarbaijan province,
Iran. The research sample includes 93 people selected by the sampling formula in unlimited population. The data collection
instrument was a questionnaire, the validity of which was confirmed
through face validity and the reliability of which was determined,
using Cronbach's alpha coefficient. The Kolmogorov-Smironov test
was used to test data normality, the t-test for identification of factors
affecting the product value, and Friedman test for prioritizing the
factors. The results show that quality, satisfaction, styling, price, finishing operation, performance, safety, worth, shape, use, and
excellence are placed from 1 to 11 priorities, respectively.
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: In metal cutting industries, mathematical/statistical
models are typically used to predict tool replacement time. These
off-line methods usually result in less than optimum replacement
time thereby either wasting resources or causing quality problems.
The few online real-time methods proposed use indirect measurement
techniques and are prone to similar errors. Our idea is based on
identifying the optimal replacement time using an electronic nose to
detect the airborne compounds released when the tool wear reaches
to a chemical substrate doped into tool material during the
fabrication. The study investigates the feasibility of the idea, possible
doping materials and methods along with data stream mining
techniques for detection and monitoring different phases of tool
wear.
Abstract: The aim of this retrospective study was to evaluate the
parameters of dental implants such as patient gender, number of
implant, failed implant before prosthetic restorations and failed
implant after implantation and failed implant after prosthetic
restorations. 135 male and 99 female patients, total 234 implant
patients which have been treated with 450 implant between 2005-
2009 years in GATA Haydarpasa Training Hospital Dental Service.
Twelve implants were failed before prosthetic restorations. Four
implant were failed after fixed prosthetic restorations. Cumulative
survival rate after prostheses were 97.56 % during 6 years period.
Abstract: Nowadays, new home appliances and office appliances
have been developed that communicate with users through the
Internet, for remote monitor and remote control. However, developments
and sales of these new appliances are just started, then,
many products in our houses and offices do not have these useful
functions. In few years, we add these new functions to the outlet,
it means multifunctional electrical power socket plug adapter. The
outlet measure power consumption of connecting appliances, and it
can switch power supply to connecting appliances, too. Using this
outlet, power supply of old appliances can be control and monitor.
And we developed the interface system using web browser to operate
it from users[1]. But, this system need to set up LAN cables between
outlets and so on. It is not convenience that cables around rooms. In
this paper, we develop the system that use wireless mobile ad hoc
network instead of wired LAN to communicate with the outlets.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: The Petri net tool INA is a well known tool by the
Petri net community. However, it lacks a graphical environment to
cerate and analyse INA models. Building a modelling tool for the
design and analysis from scratch (for INA tool for example) is
generally a prohibitive task. Meta-Modelling approach is useful to
deal with such problems since it allows the modelling of the
formalisms themselves. In this paper, we propose an approach based
on the combined use of Meta-modelling and Graph Grammars to
automatically generate a visual modelling tool for INA for analysis
purposes. In our approach, the UML Class diagram formalism is
used to define a meta-model of INA models. The meta-modelling
tool ATOM3 is used to generate a visual modelling tool according to
the proposed INA meta-model. We have also proposed a graph
grammar to automatically generate INA description of the
graphically specified Petri net models. This allows the user to avoid
the errors when this description is done manually. Then the INA tool
is used to perform the simulation and the analysis of the resulted INA
description. Our environment is illustrated through an example.
Abstract: This paper describes part of a project about Learningby-
Modeling (LbM). Studying complex systems is increasingly
important in teaching and learning many science domains. Many
features of complex systems make it difficult for students to develop
deep understanding. Previous research indicates that involvement
with modeling scientific phenomena and complex systems can play a
powerful role in science learning. Some researchers argue with this
view indicating that models and modeling do not contribute to
understanding complexity concepts, since these increases the
cognitive load on students. This study will investigate the effect of
different modes of involvement in exploring scientific phenomena
using computer simulation tools, on students- mental model from the
perspective of structure, behavior and function. Quantitative and
qualitative methods are used to report about 121 freshmen students
that engaged in participatory simulations about complex phenomena,
showing emergent, self-organized and decentralized patterns. Results
show that LbM plays a major role in students' concept formation
about complexity concepts.