Abstract: The objective of the present study is to determine
better eye end design of a mono leaf spring used in light motor
vehicle. A conventional 65Si7 spring steel leaf spring model with
standard eye, casted and riveted eye end are considered. The CAD
model of the leaf springs is prepared in CATIA and analyzed using
ANSYS. The standard eye, casted and riveted eye leaf springs are
subjected to similar loading conditions. The CAE analysis of the leaf
spring is performed for various parameters like deflection and Von-
Mises stress. Mass reduction of 62.9% is achieved in case of riveted
eye mono leaf spring as compared to standard eye mono leaf spring
for the same loading conditions.
Abstract: This paper provides a comparative study on the
performances of standard PID and adaptive PID controllers tested on
travel angle of a 3-Degree-of-Freedom (3-DOF) Quanser bench-top
helicopter. Quanser, a well-known manufacturer of educational
bench-top helicopter has developed Proportional Integration
Derivative (PID) controller with Linear Quadratic Regulator (LQR)
for all travel, pitch and yaw angle of the bench-top helicopter. The
performance of the PID controller is relatively good; however, its
performance could also be improved if the controller is combined
with adaptive element. The objective of this research is to design
adaptive PID controller and then compare the performances of the
adaptive PID with the standard PID. The controller design and test is
focused on travel angle control only. Adaptive method used in this
project is self-tuning controller, which controller’s parameters are
updated online. Two adaptive algorithms those are pole-placement
and deadbeat have been chosen as the method to achieve optimal
controller’s parameters. Performance comparisons have shown that
the adaptive (deadbeat) PID controller has produced more desirable
performance compared to standard PID and adaptive (poleplacement).
The adaptive (deadbeat) PID controller attained very fast
settling time (5 seconds) and very small percentage of overshoot (5%
to 7.5%) for 10° to 30° step change of travel angle.
Abstract: Periventricular Leukomalacia (PVL) is a White Matter
Injury (WMI) of preterm neonatal brain. Objectives of the study were
to assess the neuro-developmental outcome at one year of age and to
determine a good protocol of cranial ultrasonography to detect PVL.
Two hundred and sixty four preterm neonates were included in the
study. Series of cranial ultrasound scans were done by using a
dedicated neonatal head probe 4-10 MHz of Logic e portable
ultrasound scanner. Clinical history of seizures, abnormal head
growth (hydrocephalus or microcephaly) and developmental
milestones were assessed and neurological examinations were done
until one year of age. Among live neonates, 57% who had cystic PVL
(Grades 2 and 3) manifested as cerebral palsy. In conclusion cystic
PVL has permanent neurological disabilities like cerebral palsy.
Good protocol of real time cranial ultrasonography to detect PVL is
to perform scans at least once a week until one month and at term (40
weeks of gestation).
Abstract: With a long history, dual-task has become one of the
most intriguing research fields regarding human brain functioning
and cognition. However, findings considering effects of taskinterrelations
are limited (especially, in combined motor and
cognitive tasks). Therefore, we aimed at developing a measurement
system in order to analyse interrelation effects of cognitive and motor
tasks. On the one hand, the present study demonstrates the
applicability of the measurement system and on the other hand first
results regarding a systematisation of different task combinations are
shown. Future investigations should combine imagine technologies
and this developed measurement system.
Abstract: Cross flow water tube heat exchanger can be designed
and made operational using methods of model building and
simulation of the system. This paper projects the design and
development of a model of cross flow water tube heat-exchanger
system, simulation and validation of control analysis of different
tuning methods. Feedback and override control system is developed
using inputs acquired with the help of sensory system. A
mathematical model is formulated for analysis of system behaviour.
The temperature is regulated at the desired set point automatically.
Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.
Abstract: The problematic of gender and socioeconomic status
biased differences in academic motivation patterns is discussed.
Gender identity is understood according to symbolic interactionism
perspective: as a result of reflected appraisals, social comparisons,
self-attributions, and identifications, shaped by social environment
and family context. The effects of socioeconomic status on academic
motivation are conceptualized according to Bourdieu’s habitus
concept, reflecting the role of unconscious and internalized cultural
signals, proper to low and high socioeconomic status family contexts.
Since families differ by various socioeconomic features, the
hypothesis about possible impact of parents’ socioeconomic status on
their children’s academic motivation interfering with gender
socialization effects is held. The survey, aiming to seize gender
differences in academic motivation and self-recorded improvementoriented
efforts as a result of socialization processes operating in the
families of low and high socioeconomic status, was designed. The
results of Lithuanian higher education students’ survey are presented
and discussed.
Abstract: Nowadays, Photovoltaic-PV Farms/ Parks and large
PV-Smart Grid Interface Schemes are emerging and commonly
utilized in Renewable Energy distributed generation. However, PVhybrid-
Dc-Ac Schemes using interface power electronic converters
usually has negative impact on power quality and stabilization of
modern electrical network under load excursions and network fault
conditions in smart grid. Consequently, robust FACTS based
interface schemes are required to ensure efficient energy utilization
and stabilization of bus voltages as well as limiting switching/fault
onrush current condition. FACTS devices are also used in smart grid-
Battery Interface and Storage Schemes with PV-Battery Storage
hybrid systems as an elegant alternative to renewable energy
utilization with backup battery storage for electric utility energy and
demand side management to provide needed energy and power
capacity under heavy load conditions. The paper presents a robust
interface PV-Li-Ion Battery Storage Interface Scheme for
Distribution/Utilization Low Voltage Interface using FACTS
stabilization enhancement and dynamic maximum PV power tracking
controllers.
Digital simulation and validation of the proposed scheme is done
using MATLAB/Simulink software environment for Low Voltage-
Distribution/Utilization system feeding a hybrid Linear-Motorized
inrush and nonlinear type loads from a DC-AC Interface VSC-6-
pulse Inverter Fed from the PV Park/Farm with a back-up Li-Ion
Storage Battery.
Abstract: TiO2 thin films have been prepared by the sol-gel dipcoating
technique in order to elaborate antireflective thin films for
monocrystalline silicon (mono-Si). The titanium isopropoxyde was
chosen as a precursor with hydrochloric acid as a catalyser for
preparing a stable solution. The optical properties have been tailored
with varying the solution concentration, the withdrawn speed, and the
heat-treatment. We showed that using a TiO2 single layer with 64.5
nm in thickness, heat-treated at 450°C or 300°C reduces the mono-Si
reflection at a level lower than 3% over the broadband spectral
domains [669-834] nm and [786-1006] nm respectively. Those latter
performances are similar to the ones obtained with double layers of
low and high refractive index glasses respectively.
Abstract: The continuous decline of petroleum and natural gas
reserves and non linear rise of oil price has brought about a
realisation of the need for a change in our perpetual dependence on
the fossil fuel. A day to day increased consumption of crude and
petroleum products has made a considerable impact on our foreign
exchange reserves. Hence, an alternate resource for the conversion of
energy (both liquid and gas) is essential for the substitution of
conventional fuels. Biomass is the alternate solution for the present
scenario. Biomass can be converted into both liquid as well as
gaseous fuels and other feedstocks for the industries.
Abstract: Container handling problems at container terminals
are NP-hard problems. This paper presents an approach using
discrete-event simulation modeling to optimize solution for storage
space allocation problem, taking into account all various interrelated
container terminal handling activities. The proposed approach is
applied on a real case study data of container terminal at Alexandria
port. The computational results show the effectiveness of the
proposed model for optimization of storage space allocation in
container terminal where 54% reduction in containers handling time
in port is achieved.
Abstract: In this paper a new design of a broadband microwave
power limiter is presented and validated into simulation by using
ADS software (Advanced Design System) from Agilent technologies.
The final circuit is built on microstrip lines by using identical Zero
Bias Schottky diodes. The power limiter is designed by Associating 3
stages Schottky diodes. The obtained simulation results permit to
validate this circuit with a threshold input power level of 0 dBm until
a maximum input power of 30 dBm.
Abstract: The globalization of markets, the need to develop
competitive advantages and core competencies, among other things,
lead organizations to increasingly cross borders to operate in other
countries. The expatriation of professionals who go to work in
another country besides their own becomes increasingly common. In
order to generate data about this issue, research was conducted
concerning the perception of expatriate employees concerning
expatriation success. The research method used was case study
through a qualitative approach. This research was done through
interviews with five India expatriates and five China expatriates,
interview with expatriate department heads and analysis of company
documents. It was found that there are differences between the
organizational perception and perception of expatriates of what
constitutes mission success. The paper also provides suggestions for
further research and suggestions for future expatriates.
Abstract: The ad hoc networks are the future of wireless
technology as everyone wants fast and accurate error free information
so keeping this in mind Bit Error Rate (BER) and power is optimized
in this research paper by using the Genetic Algorithm (GA). The
digital modulation techniques used for this paper are Binary Phase
Shift Keying (BPSK), M-ary Phase Shift Keying (M-ary PSK), and
Quadrature Amplitude Modulation (QAM). This work is
implemented on Wireless Ad Hoc Networks (WLAN). Then it is
analyze which modulation technique is performing well to optimize
the BER and power of WLAN.
Abstract: In this paper, we present a robust algorithm to recognize extracted text from grocery product images captured by mobile phone cameras. Recognition of such text is challenging since text in grocery product images varies in its size, orientation,
style, illumination, and can suffer from perspective distortion.
Pre-processing is performed to make the characters scale and
rotation invariant. Since text degradations can not be appropriately
defined using well-known geometric transformations such
as translation, rotation, affine transformation and shearing, we
use the whole character black pixels as our feature vector.
Classification is performed with minimum distance classifier
using the maximum likelihood criterion, which delivers very
promising Character Recognition Rate (CRR) of 89%. We
achieve considerably higher Word Recognition Rate (WRR) of
99% when using lower level linguistic knowledge about product
words during the recognition process.
Abstract: In recent years, the compression of date (Phoenix
dactylifera L.) fruit powders (DP) to obtain date tablets (DT) has
been suggested as a promising form of valorization of non
commercial valuable date fruit (DF) varieties. To further improve
and characterize DT, the present study aims to investigate the
influence of the DP particle size and compression force on some
physical properties of DT. The results show that independently of
particle size, the hardness (y) of tablets increases with the increase of
the compression force (x) following a logarithmic law (y = a ln (bx)
where a and b are the constants of model). Further, a full factorial
design (FFD) at two levels, applied to investigate the erosion %,
reveals that the effects of time and particle size are the same in
absolute value and they are beyond the effect of the compression.
Regarding the disintegration time, the obtained results also by means
of a FFD show that the effect of the compression force exceeds 4
times that of the DP particle size. As final stage, the color parameters
in the CIELab system of DT immediately after their obtaining are
differently influenced by the size of the initial powder.
Abstract: Taking the design tolerance into account, this paper
presents a novel efficient approach to generate iso-scallop tool path for
five-axis strip machining with a barrel cutter. The cutter location is
first determined on the scallop surface instead of the design surface,
and then the cutter is adjusted to locate the optimal tool position based
on the differential rotation of the tool axis and satisfies the design
tolerance simultaneously. The machining strip width and error are
calculated with the aid of the grazing curve of the cutter. Based on the
proposed tool positioning algorithm, the tool paths are generated by
keeping the scallop height formed by adjacent tool paths constant. An
example is conducted to confirm the validity of the proposed method.
Abstract: In this study, we are interested in a species of the
family of Asteraceae (Tagetes erecta). This family is considered as a
source of antimicrobial extracts with strong capacity. The extraction
of the flavonoids is carried out by the method of liquid/liquid with the
use of successive solvents. Afterwards, we evaluated the biological
activity of the flavonoids on five pathogenic bacterial stocks such as
Escherichia coli, Bacillus subtilis, Klebsiella pneumoniae,
Pseudomonas aeruginosa and Staphylococcus aureus and two stocks
of yeasts to knowing Candida albicans) and Saccharomyces
cerevisiae, by employing the method of the aromatogramme starting
from a solid disc. The result of the antimicrobial activity shows an
action and a variable degree of sensitivity according to bacterial
stocks tested. It will be noted that the flavonoids have an inhibiting
effect on E. coli, B. subtilis, K. pneumoniae and S. aureus. But a
resistance with respect to the extract by P. aeruginosa, C. albicans
and S. cerevisiae is to be mentioned.
Abstract: The paper focus on robotic telepresence system build
around humanoid robot operated with controller-less Wizard of Oz
technique. Proposed solution gives possibility to quick start acting as
a operator with short, if any, initial training.
Abstract: The use of eXtensible Markup Language (XML) in
web, business and scientific databases lead to the development of
methods, techniques and systems to manage and analyze XML data.
Semi-structured documents suffer due to its heterogeneity and
dimensionality. XML structure and content mining represent
convergence for research in semi-structured data and text mining. As
the information available on the internet grows drastically, extracting
knowledge from XML documents becomes a harder task. Certainly,
documents are often so large that the data set returned as answer to a
query may also be very big to convey the required information. To
improve the query answering, a Semantic Tree Based Association
Rule (STAR) mining method is proposed. This method provides
intentional information by considering the structure, content and the
semantics of the content. The method is applied on Reuter’s dataset
and the results show that the proposed method outperforms well.