Abstract: Erosion and abrasion are wear mechanisms reducing
the lifetime of machine elements like valves, pump and pipe systems.
Both wear mechanisms are acting at the same time, causing a
“Synergy” effect, which leads to a rapid damage of the surface.
Different parameters are effective on erosive abrasive wear rate. In
this study effect of particle impact angle on wear rate and wear
mechanism of ductile and brittle materials was investigated. A new
slurry pot was designed for experimental investigation. As abrasive
particle, silica sand was used. Particle size was ranking between 200-
500 μm. All tests were carried out in a sand-water mixture of 20%
concentration for four hours. Impact velocities of the particles were
4.76 m/s. As ductile material steel St 37 with Vickers Hardness
Number (VHN) of 245 and quenched St 37 with 510 VHN was used
as brittle material. After wear tests, morphology of the eroded
surfaces were investigated for better understanding of the wear
mechanisms acting at different impact angles by using Scanning
Electron Microscope. The results indicated that wear rate of ductile
material was higher than brittle material. Maximum wear rate was
observed by ductile material at a particle impact angle of 300 and
decreased further by an increase in attack angle. Maximum wear rate
by brittle materials was by impact angle of 450 and decreased further
up to 900. Ploughing was the dominant wear mechanism by ductile
material. Microcracks on the surface were detected by ductile
materials, which are nucleation centers for crater formation. Number
of craters decreased and depth of craters increased by ductile
materials by attack angle higher than 300. Deformation wear
mechanism was observed by brittle materials. Number and depth of
pits decreased by brittle materials by impact angles higher than 450.
At the end it is concluded that wear rate could not be directly related
to impact angle of particles due to the different reaction of ductile and
brittle materials.
Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: This paper discusses the general methods to saturation
in the steady-state, two axis (d & q) frame models of synchronous
machines. In particular, the important role of the magnetic coupling
between the d-q axes (cross-magnetizing phenomenon), is
demonstrated. For that purpose, distinct methods of saturation
modeling of dumper synchronous machine with cross-saturation are
identified, and detailed models synthesis in d-q axes. A number of
models are given in the final developed form. The procedure and the
novel models are verified by a critical application to prove the
validity of the method and the equivalence between all developed
models is reported. Advantages of some of the models over the
existing ones and their applicability are discussed.
Abstract: There are a number of Distributed Generations (DGs)
installed in microgrid, which may have diverse path and direction of
power flow or fault current. The overcurrent protection scheme for the
traditional radial type distribution system will no longer meet the
needs of microgrid protection. Integrating the Intelligent Electronic
Device (IED) and a Supervisory Control and Data Acquisition
(SCADA) with IEC 61850 communication protocol, the paper
proposes a Microgrid Protection Management System (MPMS) to
protect power system from the fault. In the proposed method, the
MPMS performs logic programming of each IED to coordinate their
tripping sequence. The GOOSE message defined in IEC 61850 is used
as the transmission information medium among IEDs. Moreover, to
cope with the difference in fault current of microgrid between
grid-connected mode and islanded mode, the proposed MPMS applies
the group setting feature of IED to protect system and robust
adaptability. Once the microgrid topology varies, the MPMS will
recalculate the fault current and update the group setting of IED.
Provided there is a fault, IEDs will isolate the fault at once. Finally, the
Matlab/Simulink and Elipse Power Studio software are used to
simulate and demonstrate the feasibility of the proposed method.
Abstract: This paper addresses minimizing the makespan of the
distributed permutation flow shop scheduling problem. In this
problem, there are several parallel identical factories or flowshops
each with series of similar machines. Each job should be allocated to
one of the factories and all of the operations of the jobs should be
performed in the allocated factory. This problem has recently gained
attention and due to NP-Hard nature of the problem, metaheuristic
algorithms have been proposed to tackle it. Majority of the proposed
algorithms require large computational time which is the main
drawback. In this study, a general variable neighborhood search
algorithm (GVNS) is proposed where several time-saving schemes
have been incorporated into it. Also, the GVNS uses the sophisticated
method to change the shaking procedure or perturbation depending
on the progress of the incumbent solution to prevent stagnation of the
search. The performance of the proposed algorithm is compared to
the state-of-the-art algorithms based on standard benchmark
instances.
Abstract: Polymeric micro-cantilevers (Cs) are rapidly
becoming popular for MEMS applications such as chemo- and biosensing
as well as purely electromechanical applications such as
microrelays. Polymer materials present suitable physical and
chemical properties combined with low-cost mass production. Hence,
micro-cantilevers made of polymers indicate much more
biocompatibility and adaptability of rapid prototyping along with
mechanical properties. This research studies the effects of three
process and one size factors on the filling behaviour in micro cavity,
and the role of each in the replication of micro parts using different
polymer materials i.e. polypropylene (PP) SABIC 56M10 and
acrylonitrile butadiene styrene (ABS) Magnum 8434 . In particular,
the following factors are considered: barrel temperature, mould
temperature, injection speed and the thickness of micro features. The
study revealed that the barrel temperature and the injection speed are
the key factors affecting the flow length of micro features replicated
in PP and ABS. For both materials, an increase of feature sizes
improves the melt flow. However, the melt fill of micro features does
not increase linearly with the increase of their thickness.
Abstract: This study aims to increase understanding of the
transition of business models in servitization. The significance of
service in all business has increased dramatically during the past
decades. Service-dominant logic (SDL) describes this change in the
economy and questions the goods-dominant logic on which business
has primarily been based in the past. A business model canvas is one
of the most cited and used tools in defining end developing business
models. The starting point of this paper lies in the notion that the
traditional business model canvas is inherently goods-oriented and
best suits for product-based business. However, the basic differences
between goods and services necessitate changes in business model
representations when proceeding in servitization. Therefore, new
knowledge is needed on how the conception of business model and
the business model canvas as its representation should be altered in
servitized firms in order to better serve business developers and interfirm
co-creation. That is to say, compared to products, services are
intangible and they are co-produced between the supplier and the
customer. Value is always co-created in interaction between a
supplier and a customer, and customer experience primarily depends
on how well the interaction succeeds between the actors. The role of
service experience is even stronger in service business compared to
product business, as services are co-produced with the customer. This paper provides business model developers with a service
business model canvas, which takes into account the intangible,
interactive, and relational nature of service. The study employs a
design science approach that contributes to theory development via
design artifacts. This study utilizes qualitative data gathered in
workshops with ten companies from various industries. In particular,
key differences between Goods-dominant logic (GDL) and SDLbased
business models are identified when an industrial firm
proceeds in servitization. As the result of the study, an updated version of the business
model canvas is provided based on service-dominant logic. The
service business model canvas ensures a stronger customer focus and
includes aspects salient for services, such as interaction between
companies, service co-production, and customer experience. It can be
used for the analysis and development of a current service business
model of a company or for designing a new business model. It
facilitates customer-focused new service design and service
development. It aids in the identification of development needs, and
facilitates the creation of a common view of the business model.
Therefore, the service business model canvas can be regarded as a
boundary object, which facilitates the creation of a common
understanding of the business model between several actors involved.
The study contributes to the business model and service business
development disciplines by providing a managerial tool for
practitioners in service development. It also provides research insight
into how servitization challenges companies’ business models.
Abstract: This paper aims to study the heat transfer and fluid
flow characteristics of nanofluids used in spray cooling systems. The
effect of spray height, type of nanofluids and concentration of
nanofluids are numerically investigated. Five different nanofluids
such as AgH2O, Al2O3, CuO, SiO2 and TiO2 with volume fraction
range of 0.5% to 2.5% are used. The results revealed that the heat
transfer performance decreases as spray height increases. It is found
that TiO2 has the highest transfer coefficient among other nanofluids.
In dilute spray conditions, low concentration of nanofluids is
observed to be more effective in heat removal in a spray cooling
system.
Abstract: This paper will discuss how we optimize our physical
verification flow in our IC Design Department having various rule
decks from multiple foundries. Our ultimate goal is to achieve faster
time to tape-out and avoid schedule delay. Currently the physical
verification runtimes and memory usage have drastically increased
with the increasing number of design rules, design complexity, and
the size of the chips to be verified. To manage design violations, we
use a number of solutions to reduce the amount of violations needed
to be checked by physical verification engineers. The most important
functions in physical verifications are DRC (design rule check), LVS
(layout vs. schematic), and XRC (extraction). Since we have a
multiple number of foundries for our design tape-outs, we need a
flow that improve the overall turnaround time and ease of use of the
physical verification process. The demand for fast turnaround time is
even more critical since the physical design is the last stage before
sending the layout to the foundries.
Abstract: Space Vector Pulse Width Modulation is popular for
variable frequency drives. The method has several advantages over
carried based PWM and is computation intensive. The
implementation of SVPWM for multilevel inverter requires special
attention and at the same time consumes considerable resources. Due
to faster processing power and reduced over all computational
burden, FPGAs are being investigated as an alternative for other
controllers. In this paper, a space vector PWM algorithm is
implemented using FPGA which requires less computational area and
is modular in structure. The algorithm is verified experimentally for
Neutral Point Clamped inverter using FPGA development board
xc3s5000-4fg900.
Abstract: The current tools for real time management of sewer
systems are based on two software tools: the software of weather
forecast and the software of hydraulic simulation. The use of the first
ones is an important cause of imprecision and uncertainty, the use of
the second requires temporal important steps of decision because of
their need in times of calculation. This way of proceeding fact that
the obtained results are generally different from those waited. The major idea of this project is to change the basic paradigm by
approaching the problem by the "automatic" face rather than by that
"hydrology". The objective is to make possible the realization of a
large number of simulations at very short times (a few seconds)
allowing to take place weather forecasts by using directly the real
time meditative pluviometric data. The aim is to reach a system
where the decision-making is realized from reliable data and where
the correction of the error is permanent. A first model of control laws was realized and tested with different
return-period rainfalls. The gains obtained in rejecting volume vary
from 19 to 100 %. The development of a new algorithm was then
used to optimize calculation time and thus to overcome the
subsequent combinatorial problem in our first approach. Finally, this
new algorithm was tested with 16- year-rainfall series. The obtained
gains are 40 % of total volume rejected to the natural environment
and of 65 % in the number of discharges.
Abstract: Elliptic curve discrete logarithm problem(ECDLP) is
one of problems on which the security of pairing-based cryptography
is based. This paper considers Pollard’s rho method to evaluate
the security of ECDLP on Barreto-Naehrig(BN) curve that is an
efficient pairing-friendly curve. Some techniques are proposed to
make the rho method efficient. Especially, the group structure on
BN curve, distinguished point method, and Montgomery trick are
well-known techniques. This paper applies these techniques and
shows its optimization. According to the experimental results for
which a large-scale parallel system with MySQL is applied, 94-bit
ECDLP was solved about 28 hours by parallelizing 71 computers.
Abstract: When high strength reinforced concrete is exposed to
high temperature due to a fire, deteriorations occur such as loss in
strength and elastic modulus, cracking and spalling of the concrete.
Therefore, it is important to understand risk of structural safety in
building structures by studying structural behaviors and rehabilitation
of fire damaged high strength concrete structures. This paper aims at
investigating rehabilitation effect on fire damaged high strength
concrete beams using experimental and analytical methods. In the
experiments, flexural specimens with high strength concrete are
exposed to high temperatures according to ISO 834 standard time
temperature curve. From four-point loading test, results show that
maximum loads of the rehabilitated beams are similar to or higher than
those of the non-fire damaged RC beam. In addition, structural
analyses are performed using ABAQUS 6.10-3 with same conditions
as experiments to provide accurate predictions on structural and
mechanical behaviors of rehabilitated RC beams. The parameters are
the fire cover thickness and strengths of repairing mortar. Analytical
results show good rehabilitation effects, when the results predicted
from the rehabilitated models are compared to structural behaviors of
the non-damaged RC beams. In this study, fire damaged high strength concrete beams are
rehabilitated using polymeric cement mortar. The predictions from the
finite element (FE) models show good agreements with the
experimental results and the modeling approaches can be used to
investigate applicability of various rehabilitation methods for further
study.
Abstract: Present study was aimed to develop a discharge
measuring device for irrigation and laboratory channels. Experiments
were conducted on sharp edged constricted flow meters having four
types of width constrictions namely 2:1, 1.5:1, 1:1 and 90o in the
direction of flow. These devices were made of MS sheets and
installed separately in a rectangular flume. All these four devices
were tested under free and submerged flow conditions. Eight
different discharges varying from 2 lit/sec to 30 lit/sec were passed
through each device. In total around 500 observations of upstream
and downstream depths were taken in the present work. For each
discharge, free submerged and critical submergence under different
flow conditions were noted and plotted. Once the upstream and
downstream depths of flow over any of the device are known, the
discharge can be easily calculated with the help of the curves
developed for free and submerged flow conditions. The device
having contraction 2:1 is the most efficient one as it allows maximum
critical submergence.
Abstract: Recently attention has been focused on incomplete
spinal cord injuries (SCI) to the central spine caused by pressure on
parts of the white matter conduction pathway, such as the pyramidal
tract. In this paper, we focus on a training robot designed to assist with
primary walking-pattern training. The target patient for this training
robot is relearning the basic functions of the usual walking pattern; it is
meant especially for those with incomplete-type SCI to the central
spine, who are capable of standing by themselves but not of
performing walking motions. From the perspective of human
engineering, we monitored the operator’s actions to the robot and
investigated the movement of joints of the lower extremities, the
circumference of the lower extremities, and exercise intensity with the
machine. The concept of the device was to provide mild training
without any sudden changes in heart rate or blood pressure, which will
be particularly useful for the elderly and disabled. The mechanism of
the robot is modified to be simple and lightweight with the expectation
that it will be used at home.
Abstract: Two normal populations with different means and same
variance are considered, where the variance is known. The population
with the smaller sample mean is selected. Various estimators are
constructed for the mean of the selected normal population. Finally,
they are compared with respect to the bias and MSE risks by
the mehod of Monte-Carlo simulation and their performances are
analysed with the help of graphs.
Abstract: In some applications, such as image recognition or
compression, segmentation refers to the process of partitioning a
digital image into multiple segments. Image segmentation is typically
used to locate objects and boundaries (lines, curves, etc.) in images.
Image segmentation is to classify or cluster an image into several
parts (regions) according to the feature of image, for example, the
pixel value or the frequency response. More precisely, image
segmentation is the process of assigning a label to every pixel in an
image such that pixels with the same label share certain visual
characteristics. The result of image segmentation is a set of segments
that collectively cover the entire image, or a set of contours extracted
from the image. Several image segmentation algorithms were
proposed to segment an image before recognition or compression. Up
to now, many image segmentation algorithms exist and be
extensively applied in science and daily life. According to their
segmentation method, we can approximately categorize them into
region-based segmentation, data clustering, and edge-base
segmentation. In this paper, we give a study of several popular image
segmentation algorithms that are available.
Abstract: This paper investigates the thermal issue of permanent
magnet synchronous generator which is frequently used in direct
drive gearless small-scale wind turbine applications. Permanent
Magnet Synchronous Generator (PMSG) is designed with 2.5 kW
continuous and 6 kW peak power. Then considering generator
geometry, mechanical design of wind turbine is performed. Thermal
analysis and optimization is carried out considering all wind turbine
components to reach realistic results. This issue is extremely
important in research and development (R&D) process for wind
turbine applications.
Abstract: This study presents a hybrid metaheuristic algorithm
to obtain optimum designs for steel space buildings. The optimum
design problem of three-dimensional steel frames is mathematically
formulated according to provisions of LRFD-AISC (Load and
Resistance factor design of American Institute of Steel Construction).
Design constraints such as the strength requirements of structural
members, the displacement limitations, the inter-story drift and the
other structural constraints are derived from LRFD-AISC
specification. In this study, a hybrid algorithm by using teachinglearning
based optimization (TLBO) and harmony search (HS)
algorithms is employed to solve the stated optimum design problem.
These algorithms are two of the recent additions to metaheuristic
techniques of numerical optimization and have been an efficient tool
for solving discrete programming problems. Using these two
algorithms in collaboration creates a more powerful tool and
mitigates each other’s weaknesses. To demonstrate the powerful
performance of presented hybrid algorithm, the optimum design of a
large scale steel building is presented and the results are compared to
the previously obtained results available in the literature.
Abstract: Regions with extreme climate conditions such as
Astana city require energy saving measures to increase energy
performance of buildings which are responsible for more than 40% of
total energy consumption. Identification of optimal building
geometry is one of key factors to be considered. Architectural form of
a building has impact on space heating and cooling energy use,
however the interrelationship between the geometry and resultant
energy use is not always readily apparent. This paper presents a
comparative case study of two prototypical buildings with compact
building shape to assess its impact on energy performance.