Abstract: Mobile Ad hoc Networks is an autonomous system of
mobile nodes connected by multi-hop wireless links without
centralized infrastructure support. As mobile communication gains
popularity, the need for suitable ad hoc routing protocols will
continue to grow. Efficient dynamic routing is an important research
challenge in such a network. Bandwidth constrained mobile devices
use on-demand approach in their routing protocols because of its
effectiveness and efficiency. Many researchers have conducted
numerous simulations for comparing the performance of these
protocols under varying conditions and constraints. Most of them are
not aware of MAC Protocols, which will impact the relative
performance of routing protocols considered in different network
scenarios. In this paper we investigate the choice of MAC protocols
affects the relative performance of ad hoc routing protocols under
different scenarios. We have evaluated the performance of these
protocols using NS2 simulations. Our results show that the
performance of routing protocols of ad hoc networks will suffer when
run over different MAC Layer protocols.
Abstract: Added stresses due to adjacent structure should be
considered in foundation design and stress control in soil under the structure. This case is considered less than other cases in design and
calculation whereas stresses in implementation are greater than analytical stress.
Structure load are transmitted to earth by foundation and role of foundation is propagation of load on the continuous and half extreme
soil. This act cause that, present stresses lessen to allowable strength
of soil. Some researchers such as Boussinesq and westergaurd by
using of some assumption studied on this issue, theorically. Target of
this paper is study and evaluation of added stresses under structure
due to adjacent structure. For this purpose, by using of assumption, theoric relation and numeral methods, effects of adjacent structure
with 4 to 10 storeys on the main structure with 4 storeys are studied
and effect of parameters and sensitivity of them are evaluated.
Abstract: Recently, there have been an increasing interest in RFID system and RFID systems have been applied to various applications. Load balancing is a fundamental technique for providing scalability of systems by moving workload from overloaded nodes to under-loaded nodes. This paper presents an approach to adaptive load balancing for RFID middlewares. Workloads of RFID middlewares can have a considerable variation according to the location of the connected RFID readers and can abruptly change at a particular instance. The proposed approach considers those characteristics of RFID middle- wares to provide an efficient load balancing.
Abstract: This article presents the results using a parametric approach and a Wavelet Transform in analysing signals emitting from the sperm whale. The extraction of intrinsic characteristics of these unique signals emitted by marine mammals is still at present a difficult exercise for various reasons: firstly, it concerns non-stationary signals, and secondly, these signals are obstructed by interfering background noise. In this article, we compare the advantages and disadvantages of both methods: Auto Regressive models and Wavelet Transform. These approaches serve as an alternative to the commonly used estimators which are based on the Fourier Transform for which the hypotheses necessary for its application are in certain cases, not sufficiently proven. These modern approaches provide effective results particularly for the periodic tracking of the signal's characteristics and notably when the signal-to-noise ratio negatively effects signal tracking. Our objectives are twofold. Our first goal is to identify the animal through its acoustic signature. This includes recognition of the marine mammal species and ultimately of the individual animal (within the species). The second is much more ambitious and directly involves the intervention of cetologists to study the sounds emitted by marine mammals in an effort to characterize their behaviour. We are working on an approach based on the recordings of marine mammal signals and the findings from this data result from the Wavelet Transform. This article will explore the reasons for using this approach. In addition, thanks to the use of new processors, these algorithms once heavy in calculation time can be integrated in a real-time system.
Abstract: Lung cancer accounts for the most cancer related deaths for men as well as for women. The identification of cancer associated genes and the related pathways are essential to provide an important possibility in the prevention of many types of cancer. In this work two filter approaches, namely the information gain and the biomarker identifier (BMI) are used for the identification of different types of small-cell and non-small-cell lung cancer. A new method to determine the BMI thresholds is proposed to prioritize genes (i.e., primary, secondary and tertiary) using a k-means clustering approach. Sets of key genes were identified that can be found in several pathways. It turned out that the modified BMI is well suited for microarray data and therefore BMI is proposed as a powerful tool for the search for new and so far undiscovered genes related to cancer.
Abstract: Developing a supply chain management (SCM) system is costly, but important. However, because of its complicated nature, not many of such projects are considered successful. Few research publications directly relate to key success factors (KSFs) for implementing a SCM system. Motivated by the above, this research proposes a hierarchy of KSFs for SCM system implementation in the semiconductor industry by using a two-step approach. First, the literature review indicates the initial hierarchy. The second step includes a focus group approach to finalize the proposed KSF hierarchy by extracting valuable experiences from executives and managers that actively participated in a project, which successfully establish a seamless SCM integration between the world's largest semiconductor foundry manufacturing company and the world's largest assembly and testing company. Future project executives may refer the resulting KSF hierarchy as a checklist for SCM system implementation in semiconductor or related industries.
Abstract: Application of Geo-Informatic technology in land
tenure and land use on the economic crop area, to create sustainable
land, access to the area, and produce sustainable food for the demand
of its people in the community. The research objectives are to 1)
apply Geo-Informatic Technology on land ownership and agricultural
land use (cash crops) in the research area, 2) create GIS database on
land ownership and land use, 3) create database of an online Geoinformation
system on land tenure and land use. The results of this
study reveal that, first; the study area is on high slope, mountains and
valleys. The land is mainly in the forest zone which was included in
the Forest Act 1941 and National Conserved Forest 1964. Residents
gained the rights to exploit the land passed down from their
ancestors. The practice was recognized by communities. The land
was suitable for cultivating a wide variety of economic crops that was
the main income of the family. At present the local residents keep
expanding the land to grow cash crops. Second; creating a database
of the geographic information system consisted of the area range,
announcement from the Interior Ministry, interpretation of satellite
images, transportation routes, waterways, plots of land with a title
deed available at the provincial land office. Most pieces of land
without a title deed are located in the forest and national reserve
areas. Data were created from a field study and a land zone
determined by a GPS. Last; an online Geo-Informatic System can
show the information of land tenure and land use of each economic
crop. Satellite data with high resolution which could be updated and
checked on the online Geo-Informatic System simultaneously.
Abstract: Approximate tandem repeats in a genomic sequence are
two or more contiguous, similar copies of a pattern of nucleotides.
They are used in DNA mapping, studying molecular evolution
mechanisms, forensic analysis and research in diagnosis of inherited
diseases. All their functions are still investigated and not well
defined, but increasing biological databases together with tools for
identification of these repeats may lead to discovery of their specific
role or correlation with particular features. This paper presents a new
approach for finding approximate tandem repeats in a given sequence,
where the similarity between consecutive repeats is measured using
the Hamming distance. It is an enhancement of a method for finding
exact tandem repeats in DNA sequences based on the Burrows-
Wheeler transform.
Abstract: Memristor is also known as the fourth fundamental
passive circuit element. When current flows in one direction through
the device, the electrical resistance increases and when current flows
in the opposite direction, the resistance decreases. When the current
is stopped, the component retains the last resistance that it had, and
when the flow of charge starts again, the resistance of the circuit will
be what it was when it was last active. It behaves as a nonlinear
resistor with memory. Recently memristors have generated wide
research interest and have found many applications. In this paper we
survey the various applications of memristors which include non
volatile memory, nanoelectronic memories, computer logic,
neuromorphic computer architectures low power remote sensing
applications, crossbar latches as transistor replacements, analog
computations and switches.
Abstract: Nowadays, many manufacturing companies try to
reinforce their competitiveness or find a breakthrough by considering
collaboration. In Korea, more than 900 manufacturing companies are
using web-based collaboration systems developed by the
government-led project, referred to as i-Manufacturing. The system
supports some similar functions of Product Data Management (PDM)
as well as Project Management System (PMS). A web-based
collaboration system provides many useful functions for collaborative
works. This system, however, does not support new linking services
between buyers and suppliers. Therefore, in order to find new
collaborative partners, this paper proposes a framework which creates
new connections between buyers and suppliers facilitating their
collaboration, referred to as Excellent Manufacturer Scouting System
(EMSS). EMSS plays a role as a bridge between overseas buyers and
suppliers. As a part of study on EMSS, we also propose an evaluation
method of manufacturability of potential partners with six main factors.
Based on the results of evaluation, buyers may get a good guideline to
choose their new partners before getting into negotiation processes
with them.
Abstract: Computed tomography (CT) dosimetry normally uses
an ionization chamber 100 mm long to estimate the computed
tomography dose index (CTDI), however some reports have already
indicated that small devices could replace the long ion chamber to
improve quality assurance procedures in CT dosimetry. This paper
presents a novel dosimetry system based in a commercial
phototransistor evaluated for CT dosimetry. Three detector
configurations were developed for this system: with a single, two and
four devices. Dose profile measurements were obtained with them
and their angular response were evaluated. The results showed that
the novel dosimetry system with the phototransistor could be an
alternative for CT dosimetry. It allows to obtain the CT dose profile
in details and also to estimate the CTDI in longer length than the
100 mm pencil chamber. The angular response showed that the one
device detector configuration is the most adequate among the three
configurations analyzed in this study.
Abstract: The goal of this work is to describe a new algorithm for finding the optimal variable order, number of nodes for any order and other ROBDD parameters, based on a tabular method. The tabular method makes use of a pre-built backend database table that stores the ROBDD size for selected combinations of min-terms. The user uses the backend table and the proposed algorithm to find the necessary ROBDD parameters, such as best variable order, number of nodes etc. Experimental results on benchmarks are given for this technique.
Abstract: This paper describes the designs of a first and second
generation autonomous gas monitoring system and the successful
field trial of the final system (2nd generation). Infrared sensing
technology is used to detect and measure the greenhouse gases
methane (CH4) and carbon dioxide (CO2) at point sources. The
ability to monitor real-time events is further enhanced through the
implementation of both GSM and Bluetooth technologies to
communicate these data in real-time. These systems are robust,
reliable and a necessary tool where the monitoring of gas events in
real-time are needed.
Abstract: This paper presents the findings of two experiments that were performed on the Redundancy in Wireless Connection Model (RiWC) using the 802.11b standard. The experiments were simulated using OPNET 11.5 Modeler software. The first was aimed at finding the maximum number of simultaneous Voice over Internet Protocol (VoIP) users the model would support under the G.711 and G.729 codec standards when the packetization interval was 10 milliseconds (ms). The second experiment examined the model?s VoIP user capacity using the G.729 codec standard along with background traffic using the same packetization interval as in the first experiment. To determine the capacity of the model under various experiments, we checked three metrics: jitter, delay and data loss. When background traffic was added, we checked the response time in addition to the previous three metrics. The findings of the first experiment indicated that the maximum number of simultaneous VoIP users the model was able to support was 5, which is consistent with recent research findings. When using the G.729 codec, the model was able to support up to 16 VoIP users; similar experiments in current literature have indicated a maximum of 7 users. The finding of the second experiment demonstrated that the maximum number of VoIP users the model was able to support was 12, with the existence of background traffic.
Abstract: Methane is the second most important greenhouse gas
(GHG) after carbon dioxide. Amount of methane emission from
energy sector is increasing day by day with various activities. In
present work, various sources of methane emission from upstream,
middle stream and downstream of oil & gas sectors are identified and
categorised as per IPCC-2006 guidelines. Data were collected from
various oil & gas sector like (i) exploration & production of oil & gas
(ii) supply through pipelines (iii) refinery throughput & production
(iv) storage & transportation (v) usage. Methane emission factors for
various categories were determined applying Tier-II and Tier-I
approach using the collected data. Total methane emission from
Indian Oil & Gas sectors was thus estimated for the year 1990 to
2007.
Abstract: For the first time since 1940 and presentation of
theodorson-s theory, distribution of thrust, torque and efficiency
along the blade of a counter rotating propeller axial fan was studied
with a novel method in this research. A constant chord, constant
pitch symmetric fan was investigated with Reynolds Stress
Turbulence method in this project and H.E.S. method was utilized to
obtain distribution profiles from C.F.D. tests outcome. C.F.D. test
results were validated by estimation from Playlic-s analytical method.
Final results proved ability of H.E.S. method to obtain distribution
profiles from C.F.D test results and demonstrated interesting facts
about effects of solidity and differences between distributions in front
and rear section.
Abstract: Gesture recognition is a challenging task for extracting
meaningful gesture from continuous hand motion. In this paper, we propose an automatic system that recognizes isolated gesture,
in addition meaningful gesture from continuous hand motion for Arabic numbers from 0 to 9 in real-time based on Hidden Markov Models (HMM). In order to handle isolated gesture, HMM using
Ergodic, Left-Right (LR) and Left-Right Banded (LRB) topologies is applied over the discrete vector feature that is extracted from stereo
color image sequences. These topologies are considered to different
number of states ranging from 3 to 10. A new system is developed to recognize the meaningful gesture based on zero-codeword detection
with static velocity motion for continuous gesture. Therefore, the
LRB topology in conjunction with Baum-Welch (BW) algorithm for
training and forward algorithm with Viterbi path for testing presents the best performance. Experimental results show that the proposed system can successfully recognize isolated and meaningful gesture and achieve average rate recognition 98.6% and 94.29% respectively.
Abstract: Contemporary science and technologies largely widen
the gap between the spiritual and rational of the society. Industrial
and technological breakthroughs might radically affect most
processes in the society, thus losing the cultural heritage. The
thinkers recognized the dangers of the decadence in the first place. In
the present article the ways of preserving cultural heritage have been
investigated. Memory has always been a necessary condition for selfidentification,
- continuity is based on this. The authors have
supported the hypothesis that continuity and ethnic memory are the
very mechanisms that preserve cultural heritage. Such problemformulating
will facilitate another, new look at the material, spiritual
and arts spheres of the cultural heritage of numerous ethnic groups.
The fundamental works by major European and Kazakh scientists
have been taken as a basis for the research done.
Abstract: In this paper, we propose a novel adaptive
spatiotemporal filter that utilizes image sequences in order to remove
noise. The consecutive frames include: current, previous and next
noisy frames. The filter proposed in this paper is based upon the
weighted averaging pixels intensity and noise variance in image
sequences. It utilizes the Appropriate Number of Consecutive Frames
(ANCF) based on the noisy pixels intensity among the frames. The
number of consecutive frames is adaptively calculated for each
region in image and its value may change from one region to another
region depending on the pixels intensity within the region. The
weights are determined by a well-defined mathematical criterion,
which is adaptive to the feature of spatiotemporal pixels of the
consecutive frames. It is experimentally shown that the proposed
filter can preserve image structures and edges under motion while
suppressing noise, and thus can be effectively used in image
sequences filtering. In addition, the AWA filter using ANCF is
particularly well suited for filtering sequences that contain segments
with abruptly changing scene content due to, for example, rapid
zooming and changes in the view of the camera.
Abstract: Operational risk has become one of the most discussed topics in the financial industry in the recent years. The reasons for this attention can be attributed to higher investments in information systems and technology, the increasing wave of mergers and acquisitions and emergence of new financial instruments. In addition, the New Basel Capital Accord (known as Basel II) demands a capital requirement for operational risk and further motivates financial institutions to more precisely measure and manage this type of risk. The aim of this paper is to shed light on main characteristics of operational risk management and common applied methods: scenario analysis, key risk indicators, risk control self assessment and loss distribution approach.