Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: This paper presents comparative emission study of
newly introduced gasoline/LPG bifuel automotive engine in Indian
market. Emissions were tested as per LPG-Bharat stage III driving
cycle. Emission tests were carried out for urban cycle and extra urban
cycle. Total time for urban and extra urban cycle was 1180 sec.
Engine was run in LPG mode by using conversion system. Emissions
were tested as per standard procedure and were compared. Corrected
emissions were computed by deducting ambient reading from sample
reading. Paper describes detail emission test procedure and results
obtained. CO emissions were in the range of38.9 to 111.3 ppm. HC
emissions were in the range of 18.2 to 62.6 ppm. Nox emissions were
08 to 3.9 ppm and CO2 emissions were from 6719.2 to 8051 ppm.
Paper throws light on emission results of LPG vehicles recently
introduced in Indian automobile market. Objectives of this
experimental study were to measure emissions of engines in gasoline
& LPG mode and compare them.
Abstract: The purpose of this study was primarily assessing how important economic factors namely: The Thai export price of white rice, the exchange rate, and the world rice consumption affect the overall Thai white rice export, using historical data during the period 1989-2013 from the Thai Rice Exporters Association, and Food and Agricultural Organization of the United Nations. The co-integration method, regression analysis, and error correction model were applied to investigate the econometric model. The findings indicated that in the long-run, the world rice consumption, the exchange rate, and the Thai export price of white rice were the important factors affecting the export quantity of Thai white rice respectively, as indicated by their significant coefficients. Meanwhile, the rice export price was an important factor affecting the export quantity of Thai white rice in the short-run. This information is useful in the business, export opportunities, price competitiveness, and policymaker in Thailand.
Abstract: Organizational structure of the Turkish state
universities is a form of bureaucracy, a high efficient system in
rational and formal control. According to the dimensional approach
bureaucracy can occur in an organization in a degree, as some
bureaucracy characteristics can be stronger than others. In addition,
the units of an organization due to their different specific
characteristic properties can perceive the bureaucracy differently. In
the study, Hall-s Organizational Inventory, which was developed for
evaluating the degree of bureaucratization from the dimensional
perspective, is used to find out if there is a difference in the
perception of the bureaucracy between the academicians working in
three different departments and two faculties in the same university.
Abstract: This paper discusses a new, systematic approach to
the synthesis of a NP-hard class of non-regenerative Boolean
networks, described by FON[FOFF]={mi}[{Mi}], where for every
mj[Mj]∈{mi}[{Mi}], there exists another mk[Mk]∈{mi}[{Mi}], such
that their Hamming distance HD(mj, mk)=HD(Mj, Mk)=O(n), (where
'n' represents the number of distinct primary inputs). The method
automatically ensures exact minimization for certain important selfdual
functions with 2n-1 points in its one-set. The elements meant for
grouping are determined from a newly proposed weighted incidence
matrix. Then the binary value corresponding to the candidate pair is
correlated with the proposed binary value matrix to enable direct
synthesis. We recommend algebraic factorization operations as a post
processing step to enable reduction in literal count. The algorithm
can be implemented in any high level language and achieves best
cost optimization for the problem dealt with, irrespective of the
number of inputs. For other cases, the method is iterated to
subsequently reduce it to a problem of O(n-1), O(n-2),.... and then
solved. In addition, it leads to optimal results for problems exhibiting
higher degree of adjacency, with a different interpretation of the
heuristic, and the results are comparable with other methods.
In terms of literal cost, at the technology independent stage, the
circuits synthesized using our algorithm enabled net savings over
AOI (AND-OR-Invert) logic, AND-EXOR logic (EXOR Sum-of-
Products or ESOP forms) and AND-OR-EXOR logic by 45.57%,
41.78% and 41.78% respectively for the various problems.
Circuit level simulations were performed for a wide variety of
case studies at 3.3V and 2.5V supply to validate the performance of
the proposed method and the quality of the resulting synthesized
circuits at two different voltage corners. Power estimation was
carried out for a 0.35micron TSMC CMOS process technology. In
comparison with AOI logic, the proposed method enabled mean
savings in power by 42.46%. With respect to AND-EXOR logic, the
proposed method yielded power savings to the tune of 31.88%, while
in comparison with AND-OR-EXOR level networks; average power
savings of 33.23% was obtained.
Abstract: Food mileage is one of the important issues concerning environmental sustainability. In this research we have utilized a prototype platform with iterative user-centered testing. With these findings we successfully demonstrate the use of the context of persuasive methods to influence users- attitudes towards the sustainable concept.
Abstract: This research is to study the types of products and
services that employs 'ambient media and respective techniques in its
advertisement materials. Data collection has been done via analyses of a total of 62 advertisements that employed ambient media
approach in Thailand during the years 2004 to 2011. The 62 advertisement were qualifying advertisements of the Adman Awards
& Symposium under the category of Outdoor & Ambience. Analysis
results reveal that there is a total of 14 products and services that
chooses to utilize ambient media in its advertisement. Amongst all ambient media techniques, 'intrusion' uses the value of a medium in
its representation of content most often. Following intrusion is 'interaction', where consumers are invited to participate and interact
with the advertising materials. 'Illusion' ranks third in its ability to subject the viewers to distortions of reality that makes the division
between reality and fantasy less clear.
Abstract: Salinity is a measure of the amount of salts in the
water. Total Dissolved Solids (TDS) as salinity parameter are often
determined using laborious and time consuming laboratory tests, but
it may be more appropriate and economical to develop a method
which uses a more simple soil salinity index. Because dissolved ions
increase salinity as well as conductivity, the two measures are
related. The aim of this research was determine of constant
coefficients for predicting of Total Dissolved Solids (TDS) based on
Electrical Conductivity (EC) with Statistics of Correlation
coefficient, Root mean square error, Maximum error, Mean Bias
error, Mean absolute error, Relative error and Coefficient of residual
mass. For this purpose, two experimental areas (S1, S2) of Khuzestan
province-IRAN were selected and four treatments with three
replications by series of double rings were applied. The treatments
were included 25cm, 50cm, 75cm and 100cm water application. The
results showed the values 16.3 & 12.4 were the best constant
coefficients for predicting of Total Dissolved Solids (TDS) based on
EC in Pilot S1 and S2 with correlation coefficient 0.977 & 0.997 and
191.1 & 106.1 Root mean square errors (RMSE) respectively.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: This paper presents the outcomes of a qualitative
study which aims to investigate the pedagogical potentials of serious
games in the preparation of future teachers. The authors discuss the
existing problems and barriers associated with the organization of
teaching practices in Bulgaria as part of the pre-service teacher
training, as well as the attitudes and perceptions of the interviewed
academics, teachers and trainees concerning the integration of serious
games in the teaching practicum. The study outcomes strongly
confirm the positive attitudes of the respondents to the introduction
of virtual learning environments for the development of professional
skills of future teachers as a supplement to the traditional forms of
education. Through the inclusion of serious games it is expected to
improve the quality of practical training of pre-service teachers as
they overcome many of the problems identified in the existing
teaching practices. The outcomes of the study will inform the design
of the educational simulation software which is part of the project
SimAula Tomorrow's Teachers Training.
Abstract: The dynamics of Min proteins plays a center role in
accurate cell division. Although the nucleoids may presumably play
an important role in prokaryotic cell division, there is a lack of
models to account for its participation. In this work, we apply the
lattice Boltzmann method to investigate protein oscillation based on a
mesoscopic model that takes into account the nucleoid-s role. We
found that our numerical results are in reasonably good agreement
with the previous experimental results On comparing with the other
computational models without the presence of nucleoids, the
highlight of our finding is that the local densities of MinD and MinE
on the cytoplasmic membrane increases, especially along the cell
width, when the size of the obstacle increases, leading to a more
distinct cap-like structure at the poles. This feature indicated the
realistic pattern and reflected the combination of Min protein
dynamics and nucleoid-s role.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: Isobaric vapor-liquid equilibrium measurements are
reported for binary mixture of 2-Methyltetrahydrofuran and Cumene
at 97.3 kPa. The data were obtained using a vapor recirculating type
(modified Othmer's) equilibrium still. The mixture shows slight
negative deviation from ideality. The system does not form an
azeotrope. The experimental data obtained in this study are
thermodynamically consistent according to the Herington test. The
activity coefficients have been satisfactorily correlated by means of
the Margules, and NRTL equations. Excess Gibbs free energy has
been calculated from the experimental data. The values of activity
coefficients have also been obtained by the UNIFAC group
contribution method.
Abstract: Water is the main component of biological processes.
Water management is important to obtain higher productivity. In this
study, some of the yield components were investigated together with
different drought levels. Four chickpea genotypes (CDC Frontier,
CDC Luna, Sawyer and Sierra) were grown in pots with 3 different
irrigation levels (a dose of 17.5 ml, 35 ml and 70 ml for each pot per
day) after three weeks from sowing. In the research, flowering, pod
set, pod per plant, fertile pod, double seed/pod, stem diameter, plant
weight, seed per plant, 1000 seed weight, seed diameter, vegetation
length and weekly plant height were measured. Consequently,
significant differences were observed on all the investigated
characteristics owing to genotypes (except double seed/pod and stem
diameter), water levels (except first pod, seed weight and height on
3rd week) and genotype x water level interaction (except first pod,
double seed/pod, seed weight and height).
Abstract: In this paper a novel method for multiple one dimensional real valued sinusoidal signal frequency estimation in the presence of additive Gaussian noise is postulated. A computationally simple frequency estimation method with efficient statistical performance is attractive in many array signal processing applications. The prime focus of this paper is to combine the subspace-based technique and a simple peak search approach. This paper presents a variant of the Propagator Method (PM), where a collaborative approach of SUMWE and Propagator method is applied in order to estimate the multiple real valued sine wave frequencies. A new data model is proposed, which gives the dimension of the signal subspace is equal to the number of frequencies present in the observation. But, the signal subspace dimension is twice the number of frequencies in the conventional MUSIC method for estimating frequencies of real-valued sinusoidal signal. The statistical analysis of the proposed method is studied, and the explicit expression of asymptotic (large-sample) mean-squared-error (MSE) or variance of the estimation error is derived. The performance of the method is demonstrated, and the theoretical analysis is substantiated through numerical examples. The proposed method can achieve sustainable high estimation accuracy and frequency resolution at a lower SNR, which is verified by simulation by comparing with conventional MUSIC, ESPRIT and Propagator Method.
Abstract: Properties of cement pastes with fine-ground ceramics
used as an alternative binder replacing Portland cement up to 20% of
its mass are investigated. At first, the particle size distribution of
cement and fine-ground ceramics is measured using laser analyser.
Then, the material properties are studied in the early hardening
period up to 28 days. The hydration process of studied materials is
monitored by electrical conductivity measurement using TDR
sensors. The changes of materials- structures within the hardening are
observed using pore size distribution measurement. The compressive
strength measurements are done as well. Experimental results show
that the replacement of Portland cement by fine-ground ceramics in
the amount of up to 20% by mass is acceptable solution from the
mechanical point of view. One can also assume similar physical
properties of designed materials to the reference material with only
Portland cement as binder.
Abstract: This paper presents the speed regulation scheme of a small brushless dc motor (BLDC motor) with trapezoidal back-emf consideration. The proposed control strategy uses the proportional controller in which the proportional gain, kp, is appropriately adjusted by using genetic algorithms. As a result, the proportional control can perform well in order to compensate the BLDC motor with load disturbance. This confirms that the proposed speed regulation scheme gives satisfactory results.
Abstract: Development, calibration and validation of a threedimensional
model of the Legform impactor for pedestrian crash with
bumper are presented. Lower limb injury is becoming an increasingly
important concern in vehicle safety for both occupants and
pedestrians. In order to prevent lower extremity injuries to a
pedestrian when struck by a car, it is important to elucidate the
loadings from car front structures on the lower extremities and the
injury mechanism caused by these loadings. An impact test
procedure with a legform addressing lower limb injuries in car
pedestrian accidents has been proposed by EEVC/WG17. In this
study a modified legform impactor is introduced and validated
against EEVC/WG17 criteria. The finite element model of this
legform is developed using LS-DYNA software. Total mass of
legform impactor is 13.4 kg.Technical specifications including the
mass and location of the center of gravity and moment of inertia
about a horizontal axis through the respective centre of gravity in
femur and tibia are determined. The obtained results of legform
impactor static and dynamic tests are as specified in the
EEVC/WG17.
Abstract: In the analysis of structures, the nonlinear effects due to large displacement, large rotation and materially-nonlinear are very important and must be considered for the reliable analysis. The non-linear fmite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of fmite element code using the standard Galerkin weighted residual formulation. Two-dimensional plane stress model was carried out to present the shear wall response. Total Lagangian formulation, which is computationally more effective, is used in the formulation of stiffness matrices and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The details of the program formulation are highlighted and the results of the analyses are presented, along with a comparison of the response of the structure with Ansys software results. The presented model in this paper can be developed for nonlinear analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: In the paper we presented the possibility of application
collagen gels with active principle-s from marine algae extract and chlorhexidine salt in dental medicine. The hydro-alcoholic extracts
from marine algae have been used as they have been obtained. The extracts from marine algae and chlorhexidine salt (digluconate) are
incorporated in type I non-denatured fibrillar collagen matrixes. In order to obtain therapeutic effects at nanostructure level, it is important to know the rheological characteristics of the relevant mixtures of collagen gels and extracts from marine algae selected for use. In this survey we have studied mixtures made of non-denatured
fibrillar collagen hydro-gels where different concentrations of marine
algae have been incorporated. Based on the data obtained for the
shearing tensions, we have traced the rheograms – the diagrams for shearing tensions depending on the shearing speed values – from
which we have calculated the apparent viscosities as ratios between shearing tension and speed values, which have been figured in
relation to the shearing speed values, with a view to levelling
dependency.