Abstract: A finite element analysis (FEA) computer software HyperWorks is utilized in re-designing an automotive component to reduce its mass. Reduction of components mass contributes towards environmental sustainability by saving world-s valuable metal resources and by reducing carbon emission through improved overall vehicle fuel efficiency. A shape optimization analysis was performed on a rear spindle component. Pre-processing and solving procedures were performed using HyperMesh and RADIOSS respectively. Shape variables were defined using HyperMorph. Then optimization solver OptiStruct was utilized with fatigue life set as a design constraint. Since Stress-Number of Cycle (S-N) theory deals with uni-axial stress, the Signed von Misses stress on the component was used for looking up damage on S-N curve, and Gerber criterion for mean stress corrections. The optimization analysis resulted in mass reduction of 24% of the original mass. The study proved that the adopted approach has high potential use for environmental sustainability.
Abstract: A wireless Ad-hoc network consists of wireless nodes
communicating without the need for a centralized administration, in
which all nodes potentially contribute to the routing process.In this
paper, we report the simulation results of four different scenarios for
wireless ad hoc networks having thirty nodes. The performances of
proposed networks are evaluated in terms of number of hops per
route, delay and throughput with the help of OPNET simulator.
Channel speed 1 Mbps and simulation time 600 sim-seconds were
taken for all scenarios. For the above analysis DSR routing protocols
has been used. The throughput obtained from the above analysis
(four scenario) are compared as shown in Figure 3. The average
media access delay at node_20 for two routes and at node_20 for four
different scenario are compared as shown in Figures 4 and 5. It is
observed that the throughput will degrade when it will follow
different hops for same source to destination (i.e. it has dropped from
1.55 Mbps to 1.43 Mbps which is around 9.7%, and then dropped to
0.48Mbps which is around 35%).
Abstract: In gas lifted oil fields, the lift gas should be distributed optimally among the wells which share gas from a common source to maximize total oil production. One of the objectives of the paper is to show that a linear MPC consisting of a control objective and an economic objective can be used both as an optimizer and a controller for gas lifted systems. The MPC is based on linearized model of the oil field developed from first principles modeling. Simulation results show that the total oil production is increased by 3.4%. Difficulties in accurately measuring the bottom hole pressure using sensors in harsh operating conditions can be resolved by using an Unscented Kalman Filter (UKF) for estimation. In oil fields where input disturbance (total supply of gas) is not measured, UKF can also be used for disturbance estimation. Increased total oil production due to optimization leads to increased profit.
Abstract: Integration of system process information obtained
through an image processing system with an evolving knowledge
database to improve the accuracy and predictability of wear particle
analysis is the main focus of the paper. The objective is to automate
intelligently the analysis process of wear particle using classification
via self organizing maps. This is achieved using relationship
measurements among corresponding attributes of various
measurements for wear particle. Finally, visualization technique is
proposed that helps the viewer in understanding and utilizing these
relationships that enable accurate diagnostics.
Abstract: Integration of system process information obtained
through an image processing system with an evolving knowledge
database to improve the accuracy and predictability of wear debris
analysis is the main focus of the paper. The objective is to automate
intelligently the analysis process of wear particle using classification
via self-organizing maps. This is achieved using relationship
measurements among corresponding attributes of various
measurements for wear debris. Finally, visualization technique is
proposed that helps the viewer in understanding and utilizing these
relationships that enable accurate diagnostics.
Abstract: Glaucoma diagnosis involves extracting three features
of the fundus image; optic cup, optic disc and vernacular. Present
manual diagnosis is expensive, tedious and time consuming. A
number of researches have been conducted to automate this process.
However, the variability between the diagnostic capability of an
automated system and ophthalmologist has yet to be established. This
paper discusses the efficiency and variability between
ophthalmologist opinion and digital technique; threshold. The
efficiency and variability measures are based on image quality
grading; poor, satisfactory or good. The images are separated into
four channels; gray, red, green and blue. A scientific investigation
was conducted on three ophthalmologists who graded the images
based on the image quality. The images are threshold using multithresholding
and graded as done by the ophthalmologist. A
comparison of grade from the ophthalmologist and threshold is made.
The results show there is a small variability between result of
ophthalmologists and digital threshold.
Abstract: In this paper, we propose a chaotic cipher system consisting of Improved Volterra Filters and the mapping that is created from the actual voice by using Radial Basis Function Network. In order to achieve a practical system, the system supposes to use the digital communication line, such as the Internet, to maintain the parameter matching between the transmitter and receiver sides. Therefore, in order to withstand the attack from outside, it is necessary that complicate the internal state and improve the sensitivity coefficient. In this paper, we validate the robustness of proposed method from three perspectives of "Chaotic properties", "Randomness", "Coefficient sensitivity".
Abstract: For the last decade, statistics show traumatic brain
injury (TBI) is a growing concern in our legal system. In an effort to
obtain data regarding the influence of neuropsychological expert
witness testimony in a criminal case, this study tested three
hypotheses. H1: The majority of jurors will vote not guilty, due to
mild head injury. H2: The jurors will give more credence to the
testimony of the neuropsychologist rather than the psychiatrist. H3:
The jurors will be more lenient in their sentencing, given the
testimony of the neuropsychologist-s testimony. The criterion for
inclusion in the study as a participant is identical to those used for
inclusion in the eligibility for jury duty in the United States. A chisquared
test was performed to analyze the data for the three
hypotheses. The results supported all of the hypotheses; however
statistical significance was seen in H1 and H2 only.
Abstract: In this paper a non-parametric statistical pattern recognition algorithm for the problem of credit scoring will be presented. The proposed algorithm is based on a clustering k- means algorithm and allows for the determination of subclasses of homogenous elements in the data. The algorithm will be tested on two benchmark datasets and its performance compared with other well known pattern recognition algorithm for credit scoring.
Abstract: Despite the fact that B2c eCommerce has become
important in numerous economies, its adoption varies from country to
country. This paper aims to identify the factors affecting (enabling or
inhibiting) B2c eCommerce and to determine their quantitative
impact on the diffusion of online sales across countries. A dynamic
panel model analyzing the relationship between 13 factors
(Macroeconomic, Demographic, Socio-Cultural, Infrastructural and
Offer related) stemming from a complete literature analysis and the
B2c eCommerce value in 45 countries over 9 years has been
developed. Having a positive correlation coefficient, GDP, mobile
penetration, Internet user penetration and credit card penetration
resulted as enabling drivers of the B2c eCommerce value across
countries, whereas, having a negative correlation coefficient,equal
distribution of income and the development of traditional retailing
network act as inhibiting factors.
Abstract: The conceptually construction of axially chiral indolostilbenesi.eN-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'chloro-4,4',6,6'-tetramethoxy[1,1'-biphenyl]-2yl]ethenyl}phenyl)acetamide and N-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'-chloro-2,4',6,6'-tetramethoxy[1,1'-biphenyl]-4-yl]ethenyl}phenyl) acetamide are described in this paper. These structure, were obtained by the tactical combination of palladium-catalyzed coupling which produced 10-acetamido-3,5-dimethoxystilbene, follow by FeCl3-induced oxidative cyclization/dimerisation. All structures were unambiguously confirmed by 1D (1H, 13C) and 2D NMR experiment, (COSY, HMQC, HMBC) and mass spectrometry.
Abstract: Although lots of experiments have been done in enhanced oil recovery, the number of experiments which consider the effects of local and global heterogeneity on efficiency of enhanced oil recovery based on the polymer-surfactant flooding is low and rarely done. In this research, we have done numerous experiments of water flooding and polymer-surfactant flooding on a five spot glass micromodel in different conditions such as different positions of layers. In these experiments, five different micromodels with three different pore structures are designed. Three models with different layer orientation, one homogenous model and one heterogeneous model are designed. In order to import the effect of heterogeneity of porous media, three types of pore structures are distributed accidentally and with equal ratio throughout heterogeneous micromodel network according to random normal distribution. The results show that maximum EOR recovery factor will happen in a situation where the layers are orthogonal to the path of mainstream and the minimum EOR recovery factor will happen in a situation where the model is heterogeneous. This experiments show that in polymer-surfactant flooding, with increase of angles of layers the EOR recovery factor will increase and this recovery factor is strongly affected by local heterogeneity around the injection zone.
Abstract: In this paper we present an efficient system for
independent speaker speech recognition based on neural network
approach. The proposed architecture comprises two phases: a
preprocessing phase which consists in segmental normalization and
features extraction and a classification phase which uses neural
networks based on nonparametric density estimation namely the
general regression neural network (GRNN). The relative
performances of the proposed model are compared to the similar
recognition systems based on the Multilayer Perceptron (MLP), the
Recurrent Neural Network (RNN) and the well known Discrete
Hidden Markov Model (HMM-VQ) that we have achieved also.
Experimental results obtained with Arabic digits have shown that the
use of nonparametric density estimation with an appropriate
smoothing factor (spread) improves the generalization power of the
neural network. The word error rate (WER) is reduced significantly
over the baseline HMM method. GRNN computation is a successful
alternative to the other neural network and DHMM.
Abstract: The effect of antifungal compound from Bacillus
subtilis strain LB5 was tested against conidial germination of
Colletotrichum gloeosporioides and Pestalotiopsis eugeniae, causal
agent of anthracnose and fruit rot of wax apple, respectively.
Observation under scanning electron microscope and light compound
microscope revealed that conidial germination was completely
inhibited when treated with culture broth, culture filtrate, or crude
extract from strain LB5. Identification of purified antifungal
compound produced by strain LB5 in cell-free supernatant by nuclear
magnetic resonance and fast atom bombardment showed that the
active compound was iturin A-2.
Abstract: In this paper an attempt has been made to correlate the usefulness of electrodes made through powder metallurgy (PM) in comparison with conventional copper electrode during electric discharge machining. Experimental results are presented on electric discharge machining of AISI D2 steel in kerosene with copper tungsten (30% Cu and 70% W) tool electrode made through powder metallurgy (PM) technique and Cu electrode. An L18 (21 37) orthogonal array of Taguchi methodology was used to identify the effect of process input factors (viz. current, duty cycle and flushing pressure) on the output factors {viz. material removal rate (MRR) and surface roughness (SR)}. It was found that CuW electrode (made through PM) gives high surface finish where as the Cu electrode is better for higher material removal rate.
Abstract: Development of cities and villages, agricultural farms
and industrial regions in abutment and/or in the course of streams and
rivers or in prone flood lands has been caused more notations in
hydrology problems and city planning topics. In order to protection
of cities against of flood damages, embankment construction is a
desired and scientific method. The cities that located in arid zones
may damage by floods periodically. Zavvareh city in Ardestan
township(Isfahan province) with 7704 people located in Ardestan
plain that has been damaged by floods that have flowed from
dominant mountainous watersheds in past years with regard to return
period. In this study, according to flowed floods toward Zavvareh
city, was attempt to plan suitable hydraulic structures such as canals,
bridges and collectors in order to collection, conduction and
depletion of city surface runoff.
Abstract: Knowing the geometrical object pose of products in manufacturing line before robot manipulation is required and less time consuming for overall shape measurement. In order to perform it, the information of shape representation and matching of objects is become required. Objects are compared with its descriptor that conceptually subtracted from each other to form scalar metric. When the metric value is smaller, the object is considered closed to each other. Rotating the object from static pose in some direction introduce the change of value in scalar metric value of boundary information after feature extraction of related object. In this paper, a proposal method for indexing technique for retrieval of 3D geometrical models based on similarity between boundaries shapes in order to measure 3D CAD object pose using object shape feature matching for Computer Aided Testing (CAT) system in production line is proposed. In experimental results shows the effectiveness of proposed method.
Abstract: In this paper, the experimental design of using the
Taguchi method is employed to optimize the processing parameters in
the plasma arc surface hardening process. The processing parameters
evaluated are arc current, scanning velocity and carbon content of
steel. In addition, other significant effects such as the relation between
processing parameters are also investigated. An orthogonal array,
signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are
employed to investigate the effects of these processing parameters.
Through this study, not only the hardened depth increased and surface
roughness improved, but also the parameters that significantly affect
the hardening performance are identified. Experimental results are
provided to verify the effectiveness of this approach.
Abstract: Cloud Computing (CC) has become one of the most
talked about emerging technologies that provides powerful
computing and large storage environments through the use of the
Internet. Cloud computing provides different dynamically scalable
computing resources as a service. It brings economic benefits to
individuals and businesses that adopt the technology. In theory
adoption of cloud computing reduces capital and operational
expenditure on information technology. For this to be a reality there
is need to solve some challenges and at the same time addressing
concerns that consumers have about cloud computing. This paper
looks at Cloud Computing in general then highlights the challenges
of Cloud Computing and finally suggests solutions to some of the
challenges.
Abstract: The paper makes part from a complex research project
on Romanian Grey Steppe, a unique breed in terms of biological and
cultural-historical importance, on the verge of extinction and which
has been included in a preservation programme of genetic resources
from Romania. The study of genetic polymorphism of protean
fractions, especially kappa-casein, and the genotype relations of
these lactoproteins with some quantitative and qualitative features of
milk yield represents a current theme and a novelty for this breed. In
the estimation of the genetic parameters we used R.E.M.L.
(Restricted Maximum Likelihood) method.
The main lactoprotein from milk, kappa - casein (K-cz),
characterized in the specialized literature as a feature having a high
degree of hereditary transmission, behaves as such in the nucleus under
study, a value also confirmed by the heritability coefficient (h2 = 0.57
%). We must mention the medium values for milk and fat quantity
(h2=0.26, 0.29 %) and the fat and protein percentage from milk
having a high hereditary influence h2 = 0.71 - 0.63 %.
Correlations between kappa-casein and the milk quantity are
negative and strong. Between kappa-casein and other qualitative
features of milk (fat content 0.58-0.67 % and protein content 0.77-
0.87%), there are positive and very strong correlations. At the same
time, between kappa-casein and β casein (β-cz), β lactoglobulin (β-
lg) respectively, correlations are positive having high values (0.37 –
0.45 %), indicating the same causes and determining factors for the
two groups of features.