Abstract: A bauxite ore can be utilized in Bayer Process, if the
mass ratio of Al2O3 to SiO2 is greater than 10. Otherwise, its FexOy
and SiO2 content should be removed. On the other hand, removal of
TiO2 from the bauxite ore would be beneficial because of both
lowering the red mud residue and obtaining a valuable raw material
containing TiO2 mineral. In this study, the low grade diasporic
bauxite ore of Yalvaç, Isparta, Turkey was roasted under reducing
atmosphere and subjected to magnetic separation. According to the
experimental results, 800°C for reduction temperature and 20000
Gauss of magnetic intensity were found to be the optimum
parameters for removal of iron oxide and rutile from the nonmagnetic
ore. On the other hand, 600°C and 5000 Gauss were
determined to be the optimum parameters for removal of silica from
the non-magnetic ore.
Abstract: In this study, breeding biology and induced breeding
of freshwater mud eel, Monopterus cuchia was observed during the
experimental period from February to June, 2013. Breeding biology
of freshwater mud eel, Monopterus cuchia was considered in terms of
gonadosomatic index, length-weight relationship of gonad, ova
diameter and fecundity. The ova diameter was recorded from 0.3 mm
to 4.30 mm and the individual fecundity was recorded from 155 to
1495 while relative fecundity was found from 2.64 to 12.45. The
fecundity related to body weight and length of fish was also
discussed. A peak of GSI was observed 2.14±0.2 in male and 5.1
±1.09 in female. Induced breeding of freshwater mud eel,
Monopterus cuchia was also practiced with different doses of
different inducing agents like pituitary gland (PG), human chorionic
gonadotropin (HCG), Gonadotropin releasing hormone (GnRH) and
Ovuline-a synthetic hormone in different environmental conditions.
However, it was observed that the artificial breeding of freshwater
mud eel, Monopterus cuchia was not yet succeeded through inducing
agents in captive conditions, rather the inducing agent showed
negative impacts on fecundity and ovarian tissues. It was seen that
mature eggs in the oviduct were reduced, absorbed and some eggs
were found in spoiled condition.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: Organizational tendencies towards computer-based
information processing have been observed noticeably in the
third-world countries. Many enterprises are taking major initiatives
towards computerized working environment because of massive
benefits of computer-based information processing. However,
designing and developing information resource management software
for small and mid-size enterprises under budget costs and strict
deadline is always challenging for software engineers. Therefore, we
introduced an approach to design mid-size enterprise software by
using the Waterfall model, which is one of the SDLC (Software
Development Life Cycles), in a cost effective way. To fulfill research
objectives, in this study, we developed mid-sized enterprise software
named “BSK Management System” that assists enterprise software
clients with information resource management and perform complex
organizational tasks. Waterfall model phases have been applied to
ensure that all functions, user requirements, strategic goals, and
objectives are met. In addition, Rich Picture, Structured English, and
Data Dictionary have been implemented and investigated properly in
engineering manner. Furthermore, an assessment survey with 20
participants has been conducted to investigate the usability and
performance of the proposed software. The survey results indicated
that our system featured simple interfaces, easy operation and
maintenance, quick processing, and reliable and accurate transactions.
Abstract: We report the microstructural and magnetic properties
of Ni50Mn39Sn11 and Ni50Mn36Sn14 ribbon Heusler alloys.
Experimental results were obtained by differential scanning
calorymetry, X-ray diffraction and vibrating sample magnetometry
techniques. The Ni-Mn-Sn system undergoes a martensitic structural
transformation in a wide temperature range. For example, for
Ni50Mn39Sn11 the start and finish temperatures of the martensitic and
austenite phase transformation for ribbon alloy were Ms=336K,
Mf=328K, As=335K and Af=343K whereas no structural
transformation is observed for Ni50Mn36Sn14 alloys. Magnetic
measurements show the typical ferromagnetic behavior with Curie
temperature 207 K at low applied field of 50 Oe. The complex
behavior exhibited by these Heusler alloys should be ascribed to the
strong coupling between magnetism and structure, being their
magnetic behavior determined by the distance between Mn atoms.
Abstract: This paper presents a study the effect of nose radius
(Rz-mm) on cutting force components and temperatures during the
machining simulation in an orthogonal cutting process for titanium
alloy (Ti-6Al-4V). The cutting process was performed at various
nose radiuses (Rz-mm) while the depth of cut (d-mm), feed rate (fmm/
tooth) and cutting speed (vc-m/ min) were remained constant.
The main cutting force (Fc), feed cutting force (Ft) and temperatures
were estimated by using finite element modeling (FEM) through
ABAQUS/EXPLICIT software and the simulation was developed the
two-dimension via an orthogonal cutting process during machining
titanium alloy (Ti-6Al-4V). The results led to the conclusion that the
nose radius (Rz-mm) has affected directly on the cutting force
components. However, temperature gave no indication or has no
significant relation with nose radius during machining titanium alloy
(Ti-6Al-4V). Hence, any increase or decrease in the nose radius (Rzmm)
during machining operation led to effect on the cutting forces
and thus it will be effective on surface finish, quality, and quantity of
products.
Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: Co-crystal is believed to improve the solubility and
dissolution rates and thus, enhanced the bioavailability of poor water
soluble drugs particularly during the oral route of administration.
With the existing of poorly soluble drugs in pharmaceutical industry,
the screening of co-crystal formation using carbamazepine (CBZ) as
a model drug compound with dicarboxylic acids co-crystal formers
(CCF) namely fumaric (FA) and succinic (SA) acids in ethanol has
been studied. The co-crystal formations were studied by varying the
mol ratio values of CCF to CBZ to access the effect of CCF
concentration on the formation of the co-crystal. Solvent evaporation,
slurry and cooling crystallization which representing the solution
based method co-crystal screening were used. Based on the
differential scanning calorimetry (DSC) analysis, the melting point of
CBZ-SA in different ratio was in the range between 188oC-189oC.
For CBZ-FA form A and CBZ-FA form B the melting point in
different ratio were in the range of 174oC-175oC and 185oC-186oC
respectively. The product crystal from the screening was also
characterized using X-ray powder diffraction (XRPD). The XRPD
pattern profile analysis has shown that the CBZ co-crystals with FA
and SA were successfully formed for all ratios studied. The findings
revealed that CBZ-FA co-crystal were formed in two different
polymorphs. It was found that CBZ-FA form A and form B were
formed from evaporation and slurry crystallization methods
respectively. On the other hand, in cooling crystallization method,
CBZ-FA form A was formed at lower mol ratio of CCF to CBZ and
vice versa. This study disclosed that different methods and mol ratios
during the co-crystal screening can affect the outcome of co-crystal
produced such as polymorphic forms of co-crystal and thereof. Thus,
it was suggested that careful attentions is needed during the screening
since the co-crystal formation is currently one of the promising
approach to be considered in research and development for
pharmaceutical industry to improve the poorly soluble drugs.
Abstract: In this research paper were investigated the main
regularities of a radical bromination reaction of decalin. There had
been studied the temperature effect, durations of reaction, frequency
rate of process, a ratio of initial components, type and number of the
initiator on decalin bromination degree.
There were specified optimum conditions of synthesis of a
perbromodecalin by the method of a decalin bromination. There are
developed the technological flowchart of receiving a
perbromodecalin and the mass balance of process on the first and the
subsequent loadings of components.
The results of research of antibacterial and antifungal activity of
synthesized bromoderivatives have been represented.
Abstract: The elastic period has a primary role in the seismic
assessment of buildings. Reliable calculations and/or estimates of the
fundamental frequency of a building and its site are essential during
analysis and design process. Various code formulas based on
empirical data are generally used to estimate the fundamental
frequency of a structure. For existing structures, in addition to code
formulas and available analytical tools such as modal analyses,
various methods of testing including ambient and forced vibration
testing procedures may be used to determine dynamic characteristics.
In this study, the dynamic properties of the 32 buildings located in
the Madinah of Saudi Arabia were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Ambient vibration measurements of buildings have been
analyzed and the fundamental longitudinal and transverse periods for
all tested buildings are presented. The fundamental mode of vibration
has been compared in plots with codes formulae (Saudi Building
Code, EC8, and UBC1997). The results indicate that measured
periods of existing buildings are shorter than that given by most
empirical code formulas. Recommendations are given based on the
common design and construction practice in Madinah city.
Abstract: The management of Helicobacter pylori (H. pylori)
eradication is still a matter of discussion, full effectiveness is rarely
achieved, and it has many adverse effects. The use of probiotics may
be associated with better eradication rates and possibly prevention of
adverse events due to antibiotic therapy. The present clinical study
was undertaken to evaluate the efficacy of a specially designed
fermented milk product, containing Bifidobacterium lactis B420, on
the eradication of H. pylori infection in a prospective, randomized,
double-blind, controlled study in humans. Four test fermented milks
(FM) were specially designed in which counts of viable cells in all
products were 10^10 Log CFU. 100 mL-1 for Bifidobacterium lactis -
Bifidobacterium species 420. 190 subjects infected with H. pylori,
with previous diagnosis of functional dyspepsia according to Rome
III criteria entered the study. Bifidobacterium lactis B420,
administered twice a day for 90 days was not able to eradicate H.
pylori in Brazilian patients with functional dyspepsia.
Abstract: Recently, universities are increasingly consuming
energy to support various activities. A large population of staff and
students in Malaysian universities has led to excessive energy
consumption which directly gives an impact to the environment. The
key question then ascended “How well is an energy management
(EM) been practiced in universities without taking the Critical
Success Factors (CSFs) into consideration to ensure the management
of university achieves the goals in reducing energy consumption.
Review on past literature is carried out to establish CSFs for EM best
practices. Thus, this paper highlighted the CSFs which have to be
focused on by management of university to successfully measure the
EM implementation and its performance. At the end of this paper, a
theoretical framework is developed for EM success factors towards
sustainable university.
Abstract: In this paper, two options of anodic alumina barrier
layer thinning have been demonstrated. The approaches varied with
the duration of the voltage step. It was found that too long step of the
barrier layer thinning process leads to chemical etching of the
nanopores on their top. At the bottoms pores are not fully opened
what is disadvantageous for further applications in nanofabrication.
On the other hand, while the duration of the voltage step is controlled
by the current density (value of the current density cannot exceed
75% of the value recorded during previous voltage step) the pores are
fully opened. However, pores at the bottom obtained with this
procedure have smaller diameter, nevertheless this procedure
provides electric contact between the bare aluminum (substrate) and
electrolyte, what is suitable for template assisted electrodeposition,
one of the most cost-efficient synthesis method in nanotechnology.
Abstract: Sandwich structure composites produced by epoxy
core and aluminium skin were developed as potential building
materials. Interface bonding between core and skin was controlled by
varying kenaf content. Five different weight percentage of kenaf
loading ranging from 10 wt% to 50 wt% were employed in the core
manufacturing in order to study the mechanical properties of the
sandwich composite. Properties of skin aluminium with epoxy were
found to be affected by drying time of the adhesive. Mechanical
behavior of manufactured sandwich composites in relation with
properties of constituent materials was studied. It was found that 30
wt% of kenaf loading contributed to increase the flexural strength and
flexural modulus up to 102 MPa and 32 GPa, respectively. Analysis
were done on the flatwise and edgewise compression test. For
flatwise test, it was found that 30 wt% of fiber loading could
withstand maximum force until 250 kN, with compressive strength
results at 96.94 MPa. However, at edgewise compression test, the
sandwich composite with same fiber loading only can withstand 31
kN of the maximum load with 62 MPa of compressive strength
results.
Abstract: An existing RC building in Madinah is seismically
evaluated with and without infill wall. Four model systems have been
considered i.e. model I (no infill), model IIA (strut infill-update from
field test), model IIB (strut infill- ASCE/SEI 41) and model IIC (strut
infill-Soft storey- ASCE/SEI 41). Three dimensional pushover
analyses have been carried out using SAP2000 software
incorporating inelastic material behavior for concrete, steel and infill
walls. Infill wall has been modeled as equivalent strut according to
suggested equation matching field test measurements and to the
ASCE/SEI 41 equation. The effect of building modeling on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madinah area has been investigated. The
response modification factor (R) for the 5 story RC building is
evaluated from capacity and demand spectra (ATC-40) for the
studied models. The results are summarized and discussed.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: Periventricular Leukomalacia (PVL) is a White Matter
Injury (WMI) of preterm neonatal brain. Objectives of the study were
to assess the neuro-developmental outcome at one year of age and to
determine a good protocol of cranial ultrasonography to detect PVL.
Two hundred and sixty four preterm neonates were included in the
study. Series of cranial ultrasound scans were done by using a
dedicated neonatal head probe 4-10 MHz of Logic e portable
ultrasound scanner. Clinical history of seizures, abnormal head
growth (hydrocephalus or microcephaly) and developmental
milestones were assessed and neurological examinations were done
until one year of age. Among live neonates, 57% who had cystic PVL
(Grades 2 and 3) manifested as cerebral palsy. In conclusion cystic
PVL has permanent neurological disabilities like cerebral palsy.
Good protocol of real time cranial ultrasonography to detect PVL is
to perform scans at least once a week until one month and at term (40
weeks of gestation).
Abstract: Science and technology has a major impact on many
societal domains such as communication, medicine, food,
transportation, etc. However, this dominance of modern technology
can have a negative unintended impact on indigenous systems, and in
particular on indigenous foods. This problem serves as a motivation
to this study whose aim is to examine the perceptions of learners on
the usefulness of Information and Communication Technologies
(ICTs) for learning about indigenous foods. This aim will be
subdivided into two types of research objectives. The design and
identification of theories and models will be achieved using literature
content analysis. The objective on the empirical testing of such
theories and models will be achieved through the survey of
Hospitality studies learners from different schools in the iLembe and
Umgungundlovu Districts of the South African Kwazulu-Natal
province. SPSS is used to quantitatively analyze the data collected by
the questionnaire of this survey using descriptive statistics and
Pearson correlations after the assessment of the validity and the
reliability of the data. The main hypothesis behind this study is that
there is a connection between the demographics of learners, their
perceptions on the usefulness of ICTs for learning about indigenous
foods, and the following personality and eLearning related theories
constructs: Computer self-efficacy, Trust in ICT systems, and
Conscientiousness; as suggested by existing studies on learning
theories. This hypothesis was fully confirmed by the survey
conducted by this study except for the demographic factors where
gender and age were not found to be determinant factors of learners’
perceptions on the usefulness of ICTs for learning about indigenous
foods.
Abstract: This paper presents the hardware implemented and
validation for a special system to assist the unprofessional users of
car with back trailers. The system consists of two platforms; the front
car platform (C) and the trailer platform (T). The main objective is to
control the Trailer platform using the actuators found in the front
platform (c). The mobility of the platform (C) is investigated and
inverse and forward kinematics model is obtained for both platforms
(C) and (T).The system is simulated using Matlab M-file and the
simulation examples results illustrated the system performance. The
system is constructed with a hardware setup for the front and trailer
platform. The hardware experimental results and the simulated
examples outputs showed the validation of the hardware setup.
Abstract: Dissimilar joining of Titanium and Aluminum thin
sheets has potential applications in aerospace and automobile
industry which can reduce weight and cost and improve strength,
corrosion resistance and high temperature properties. However
successful welding of Titanium/Aluminium sheets is of challenge due
to differences in physical, chemical and metallurgical properties
between the two. This paper describes research results of Laser Beam
Welding (LBW) of Ti/Al thin sheets in which many researchers have
recently performed and critically reviewed from different
perspectives. Also some of notable works in the field of laser welding
with changes in mechanical properties, crack propagation, diffusion
behavior, chemical potential, interfacial reaction and the
microstructure are reported.