Abstract: Employees commonly encounter unpredictable and
unavoidable work related stressors. Exposure to such stressors can
evoke negative appraisals and associated adverse mental, physical,
and behavioral responses. Because Acceptance and Commitment
Therapy (ACT) emphasizes acceptance of unavoidable stressors and
diffusion from negative appraisals, it may be particularly beneficial
for work stress. Forty-five workers were randomly assigned to an
ACT intervention for work stress (n = 21) or a waitlist control group
(n = 24). The intervention consisted of two 3-hour sessions spaced
one week apart. An examination of group process and outcomes was
conducted using the Revised Sessions Rating Scale. Results indicated
that the ACT participants reported that they perceived the
intervention to be supportive, task focused, and without adverse
therapist behaviors (e.g., feelings of being criticized or discounted).
Additionally, the second session (values clarification and
commitment to action) was perceived to be more supportive and task
focused than the first session (mindfulness, defusion). Process ratings
were correlated with outcomes. Results indicated that perceptions of
therapy supportiveness and task focus were associated with reduced
psychological distress and improved perceived physical health.
Abstract: In first stage of each microwave receiver there is Low
Noise Amplifier (LNA) circuit, and this stage has important rule in
quality factor of the receiver. The design of a LNA in Radio
Frequency (RF) circuit requires the trade-off many importance
characteristics such as gain, Noise Figure (NF), stability, power
consumption and complexity. This situation Forces desingners to
make choices in the desing of RF circuits. In this paper the aim is to
design and simulate a single stage LNA circuit with high gain and
low noise using MESFET for frequency range of 5 GHz to 6 GHz.
The desing simulation process is down using Advance Design
System (ADS). A single stage LNA has successfully designed with
15.83 dB forward gain and 1.26 dB noise figure in frequency of 5.3
GHz. Also the designed LNA should be working stably In a
frequency range of 5 GHz to 6 GHz.
Abstract: In the visual servoing systems, the data obtained by
Visionary is used for controlling robots. In this project, at first the
simulator which was proposed for simulating the performance of a
6R robot before, was examined in terms of software and test, and in
the proposed simulator, existing defects were obviated. In the first
version of simulation, the robot was directed toward the target object only in a Position-based method using two cameras in the
environment. In the new version of the software, three cameras were used simultaneously. The camera which is installed as eye-inhand on the end-effector of the robot is used for visual servoing in a
Feature-based method. The target object is recognized according to
its characteristics and the robot is directed toward the object in compliance with an algorithm similar to the function of human-s
eyes. Then, the function and accuracy of the operation of the robot are examined through Position-based visual servoing method using
two cameras installed as eye-to-hand in the environment. Finally, the obtained results are tested under ANSI-RIA R15.05-2 standard.
Abstract: Composite of Celatom-ZeoliteY (Cel-ZY) was used to
remove cobalt ion from an aqueous solution using batch mode.
ZeoliteY has successfully superimposed on Celatom FW-14 surface
using hydrothermal treatment .The product was synthesized as a
novel of hierarchical porous material. It was observed from the
results that Cel-ZY has higher ability to remove cobalt ions than the
pure ZeoliteY powder (PZY) synthesized under the same conditions.
Several parameters were studied in this project to investigate the
effect of removal cobalt ion such as pH and initial cobalt
concentration. It was clearly observed that the uptake of cobalt ions
was affected with increase these parameters. The results proved that
the product can be used effectively to remove Co2+ ions from
wastewater as an environmentally friendly alternative.
Abstract: Modern Society is strongly dependent on a reliable
power supply. The availability of cheap and reliable supply of
electrical energy is an indicator of societal welfare. Uninterrupted
reliable operation of a modern power system depends to a great
extent on reliable and satisfactory performance of insulators under
different environmental conditions. This paper reports result of
natural pollution tests that have been done at sites around city of
Aligarh (India). Flashover voltage per insulation distance (FOVUID)
of porcelain disc insulator for different pH values, ESDD has been
recorded for proper correlation between electrical and chemical
parameters. The pH of the contaminants has been suggested to be an
effective pollution severity indicator and may be used as a diagnostic
parameter for proper maintenance of porcelain insulators.
Abstract: Nanostructured Iron Oxide with different
morphologies of rod-like and granular have been suc-cessfully
prepared via a solid-state reaction in the presence of NaCl, NaBr, NaI
and NaN3, respectively. The added salts not only prevent a drastic
increase in the size of the products but also provide suitable
conditions for the oriented growth of primary nanoparticles. The
formation mechanisms of these materials by solid-state reaction at
ambient temperature are proposed. The photocatalytic experiments
for congo red (CR) have demonstrated that the mixture of α-Fe2O3
and Fe3O4 nanostructures were more efficient than α-Fe2O3
nanostructures.
Abstract: This paper describes simple implementation of
homotopy (also called continuation) algorithm for determining the proper resistance of the resistor to dissipate energy at a specified rate of an electric circuit. Homotopy algorithm can be considered as a developing of the classical methods in numerical computing such as Newton-Raphson and fixed
point methods. In homoptopy methods, an embedding
parameter is used to control the convergence. The method purposed in this work utilizes a special homotopy called Newton homotopy. Numerical example solved in MATLAB is given to show the effectiveness of the purposed method
Abstract: Computers are being integrated in the various aspects
of human every day life in different shapes and abilities. This fact
has intensified a requirement for the software development
technologies which is ability to be: 1) portable, 2) adaptable, and 3)
simple to develop. This problem is also known as the Pervasive
Computing Problem (PCP) which can be implemented in different
ways, each has its own pros and cons and Context Oriented
Programming (COP) is one of the methods to address the PCP.
In this paper a design for a COP framework, a context aware
framework, is presented which has eliminated weak points of a
previous design based on interpreter languages, while introducing the
compiler languages power in implementing these frameworks.
The key point of this improvement is combining COP and
Dependency Injection (DI) techniques. Both old and new frameworks
are analyzed to show advantages and disadvantages. Finally a
simulation of both designs is proposed to indicating that the practical
results agree with the theoretical analysis while the new design runs
almost 8 times faster.