Abstract: Porcelain specimens were fired at 6C/min to 1250C (dwell time 0.5-3h) and cooled at 6C/min to room temperature. Additionally, three different slower firing/cooling cycles were tried. Sintering profile and effects on MOR, crystalline phase content and morphology were investigated using dilatometry, 4-point bending strength, XRD and FEG-SEM respectively. Industrial-sized specimens prepared using the promising cycle were tested basing on the ANSI standards. Increasing dwell time from 1h to 3h at peak temperature of 1250C resulted in neither a significant effect on the quartz and mullite content nor MOR. Reducing the firing/cooling rate to below 6C/min, for peak temperature of 1250C (dwell time of 1h) does not result in improvement of strength of porcelain. The industrial sized specimen exhibited flashover voltages of 20.3kV (dry) and 9.3kV (wet) respectively, transverse strength of 12.5kN and bulk density of 2.27g/cm3, which are satisfactory. There was however dye penetration during porosity test. KeywordsDwell time, Microstructure, Porcelain, Strength.
Abstract: Changing in consumers lifestyles and food
consumption patterns provide a great opportunity in developing the
functional food sector in Malaysia. There is only a little knowledge
about whether Malaysian consumers are aware of functional food and
if so what image consumers have of this product. The objective of
this research is to determine the extent to which selected socioeconomic
characteristics and attitudes influence consumers-
awareness of functional food. A survey was conducted in the Klang
Valley, Malaysia where 439 respondents were interviewed using a
structured questionnaire. The result shows that most respondents
have a positive attitude towards functional food. For the binary
logistic estimation, the results indicate that age, income and other
factors such as concern about food safety, subscribing to cooking or
health magazines, being a vegetarian and consumers who have been
involved in a food production company significantly influence
Malaysian consumers- awareness towards functional food.
Abstract: Volume rendering is widely used in medical CT image
visualization. Applying 3D image visualization to diagnosis
application can require accurate volume rendering with high
resolution. Interpolation is important in medical image processing
applications such as image compression or volume resampling.
However, it can distort the original image data because of edge
blurring or blocking effects when image enhancement procedures
were applied. In this paper, we proposed adaptive tension control
method exploiting gradient information to achieve high resolution
medical image enhancement in volume visualization, where restored
images are similar to original images as much as possible. The
experimental results show that the proposed method can improve
image quality associated with the adaptive tension control efficacy.
Abstract: One of the basic concepts in marketing is the concept
of meeting customers- needs. Since customer satisfaction is essential
for lasting survival and development of a business, screening and
observing customer satisfaction and recognizing its underlying
factors must be one of the key activities of every business.
The purpose of this study is to recognize the drivers that effect
customer satisfaction in a business-to-business situation in order to
improve marketing activities. We conducted a survey in which 93
business customers of a manufacturer of Diesel Generator in Iran
participated and they talked about their ideas and satisfaction of
supplier-s services related to its products. We developed the measures
for drivers of satisfaction first by as investigative research (by means
of feedback from executives and customers of sponsoring firm). Then
based on these measures, we created a mail survey, and asked the
respondents to explain their opinion about the sponsoring firm which
was a supplier of diesel generator and similar products. Furthermore,
the survey required the participants to mention their functional areas
and their company features.
In Conclusion we found that there are three drivers for customer
satisfaction, which are reliability, information about product, and
commercial features. Buyers/users from different functional areas
attribute different degree of importance to the last two drivers. For
instance, people from buying and management areas believe that
commercial features are more important than information about
products. But people in engineering, maintenance and production
areas believe that having information about products is more
important than commercial aspects. Marketing experts should
consider the attribute of customers regarding information about the
product and commercial features to improve market share.
Abstract: This paper proposes a delay-dependent leader-following consensus condition of multi-agent systems with both communication delay and probabilistic self-delay. The proposed methods employ a suitable piecewise Lyapunov-Krasovskii functional and the average dwell time approach. New consensus criterion for the systems are established in terms of linear matrix inequalities (LMIs) which can be easily solved by various effective optimization algorithms. Numerical example showed that the proposed method is effective.
Abstract: In this paper, we have compared the performance of a Turbo and Trellis coded optical code division multiple access (OCDMA) system. The comparison of the two codes has been accomplished by employing optical orthogonal codes (OOCs). The Bit Error Rate (BER) performances have been compared by varying the code weights of address codes employed by the system. We have considered the effects of optical multiple access interference (OMAI), thermal noise and avalanche photodiode (APD) detector noise. Analysis has been carried out for the system with and without double optical hard limiter (DHL). From the simulation results it is observed that a better and distinct comparison can be drawn between the performance of Trellis and Turbo coded systems, at lower code weights of optical orthogonal codes for a fixed number of users. The BER performance of the Turbo coded system is found to be better than the Trellis coded system for all code weights that have been considered for the simulation. Nevertheless, the Trellis coded OCDMA system is found to be better than the uncoded OCDMA system. Trellis coded OCDMA can be used in systems where decoding time has to be kept low, bandwidth is limited and high reliability is not a crucial factor as in local area networks. Also the system hardware is less complex in comparison to the Turbo coded system. Trellis coded OCDMA system can be used without significant modification of the existing chipsets. Turbo-coded OCDMA can however be employed in systems where high reliability is needed and bandwidth is not a limiting factor.
Abstract: In this paper, the steady-state temperature of a sample 500 KW two rotor one stator Non-slotted axial flux permanent magnet motor is calculated using the finite element simulator software package. Due to the high temperature in various parts of the machine, especially at stator winding, a cooling system is designed for the motor and the temperature is recalculated. The results show that the temperature obtained for the parts is within the permissible range.
Abstract: Technology transfer of renewable energy technologies is very often unsuccessful in the developing world. Aside from challenges that have social, economic, financial, institutional and environmental dimensions, technology transfer has generally been misunderstood, and largely seen as mere delivery of high tech equipment from developed to developing countries or within the developing world from R&D institutions to society. Technology transfer entails much more, including, but not limited to: entire systems and their component parts, know-how, goods and services, equipment, and organisational and managerial procedures. Means to facilitate the successful transfer of energy technologies, including the sharing of lessons are subsequently extremely important for developing countries as they grapple with increasing energy needs to sustain adequate economic growth and development. Improving the success of technology transfer is an ongoing process as more projects are implemented, new problems are encountered and new lessons are learnt. Renewable energy is also critical to improve the quality of lives of the majority of people in developing countries. In rural areas energy is primarily traditional biomass. The consumption activities typically occur in an inefficient manner, thus working against the notion of sustainable development. This paper explores the implementation of technology transfer in the developing world (sub-Saharan Africa). The focus is necessarily on RETs since most rural energy initiatives are RETs-based. Additionally, it aims to highlight some lessons drawn from the cited RE projects and identifies notable differences where energy technology transfer was judged to be successful. This is done through a literature review based on a selection of documented case studies which are judged against the definition provided for technology transfer. This paper also puts forth research recommendations that might contribute to improved technology transfer in the developing world. Key findings of this paper include: Technology transfer cannot be complete without satisfying pre-conditions such as: affordability, maintenance (and associated plans), knowledge and skills transfer, appropriate know how, ownership and commitment, ability to adapt technology, sound business principles such as financial viability and sustainability, project management, relevance and many others. It is also shown that lessons are learnt in both successful and unsuccessful projects.
Abstract: Bone material is treated as heterogeneous and hierarchical in nature therefore appropriate size of bone specimen is required to analyze its tensile properties at a particular hierarchical level. Tensile properties of cortical bone are important to investigate the effect of drug treatment, disease and aging as well as for development of computational and analytical models. In the present study tensile properties of buffalo as well as goat femoral and tibiae cortical bone are analyzed using sub-size tensile specimens. Femoral cortical bone was found to be stronger in tension as compared to the tibiae cortical bone and the tensile properties obtained using sub-size specimens show close resemblance with the tensile properties of full-size cortical specimens. A two dimensional finite element (FE) modal was also applied to simulate the tensile behavior of sub-size specimens. Good agreement between experimental and FE model was obtained for sub-size tensile specimens of cortical bone.
Abstract: Routing in MANET is extremely challenging because
of MANETs dynamic features, its limited bandwidth, frequent
topology changes caused by node mobility and power energy
consumption. In order to efficiently transmit data to destinations, the
applicable routing algorithms must be implemented in mobile ad-hoc
networks. Thus we can increase the efficiency of the routing by
satisfying the Quality of Service (QoS) parameters by developing
routing algorithms for MANETs. The algorithms that are inspired by
the principles of natural biological evolution and distributed
collective behavior of social colonies have shown excellence in
dealing with complex optimization problems and are becoming more
popular. This paper presents a survey on few meta-heuristic
algorithms and naturally-inspired algorithms.
Abstract: Alumina matrix composites with addition of hexagonal boron nitride (hBN), acting as solid lubricant, were produced. Main purpose of solid lubricants is to dispose the necessity of using cooling lubricants in machining process. Hot pressing was used as a consolidating process for Al2O3-x%wt.hBN (x=1/ 2,5/ 5 /7,5 /10) composites. Properties of sinters such as relative density, hardness, Young-s modulus and fracture toughness were examined. Obtained samples characterize by high relative density. Hardness and fracture toughness values allow the use of alumina – hBN composites for machining steels even in hardened condition. However it was observed that high weight content of hBN can negatively influence the mechanical properties of composites.
Abstract: Technological innovation capability (TIC) is
defined as a comprehensive set of characteristics of a firm that
facilities and supports its technological innovation strategies.
An audit to evaluate the TICs of a firm may trigger
improvement in its future practices. Such an audit can be used
by the firm for self assessment or third-party independent
assessment to identify problems of its capability status. This
paper attempts to develop such an auditing framework that
can help to determine the subtle links between innovation
capabilities and business performance; and to enable the
auditor to determine whether good practice is in place. The
seven TICs in this study include learning, R&D, resources
allocation, manufacturing, marketing, organization and
strategic planning capabilities. Empirical data was acquired
through a survey study of 200 manufacturing firms in the
Hong Kong/Pearl River Delta (HK/PRD) region. Structural
equation modelling was employed to examine the
relationships among TICs and various performance indicators:
sales performance, innovation performance, product
performance, and sales growth. The results revealed that
different TICs have different impacts on different
performance measures. Organization capability was found to
have the most influential impact. Hong Kong manufacturers
are now facing the challenge of high-mix-low-volume
customer orders. In order to cope with this change, good
capability in organizing different activities among various
departments is critical to the success of a company.
Abstract: Direct numerical simulation (DNS) is used to study the evolution of a boundary layer that was laminar initially followed by separation and then reattachment owing to generation of turbulence. This creates a closed region of recirculation, known as the laminar-separation bubble. The present simulation emulates the flow environment encountered in a modern LP turbine blade, where a laminar separation bubble may occur on the suction surface. The unsteady, incompressible three-dimensional (3-D) Navier-Stokes (NS) equations have been solved over a flat plate in the Cartesian coordinates. The adverse pressure gradient, which causes the flow to separate, is created by a boundary condition. The separated shear layer undergoes transition through appearance of ╬ø vortices, stretching of these create longitudinal streaks. Breakdown of the streaks into small and irregular structures makes the flow turbulent downstream.
Abstract: We investigated this hypothesis that arterial CO2 pressure (PaCO2) drives ventilation (V.E) with a time delay duringrecovery from short impulse-like exercise (10 s) with work load of 200 watts. V.E and end tidal CO2 pressure (PETCO2) were measured continuously during rest, warming up, exercise and recovery periods. PaCO2 was predicted (PaCO2 pre) from PETCO2 and tidal volume (VT). PETCO2 and PaCO2 pre peaked at 20 s of recovery. V.E increased and peaked at the end of exercise and then decreased during recovery; however, it peaked again at 30 s of recovery, which was 10 s later than the peak of PaCO2 pre. The relationship between V. E and PaCO2pre was not significant by using data of them obtained at the same time but was significant by using data of V.E obtained 10 s later for data of PaCO2 pre. The results support our hypothesis that PaCO2 drives V.E with a time delay.
Abstract: A spatial classification technique incorporating a State of Art Feature Extraction algorithm is proposed in this paper for classifying a heterogeneous classes present in hyper spectral images. The classification accuracy can be improved if and only if both the feature extraction and classifier selection are proper. As the classes in the hyper spectral images are assumed to have different textures, textural classification is entertained. Run Length feature extraction is entailed along with the Principal Components and Independent Components. A Hyperspectral Image of Indiana Site taken by AVIRIS is inducted for the experiment. Among the original 220 bands, a subset of 120 bands is selected. Gray Level Run Length Matrix (GLRLM) is calculated for the selected forty bands. From GLRLMs the Run Length features for individual pixels are calculated. The Principle Components are calculated for other forty bands. Independent Components are calculated for next forty bands. As Principal & Independent Components have the ability to represent the textural content of pixels, they are treated as features. The summation of Run Length features, Principal Components, and Independent Components forms the Combined Features which are used for classification. SVM with Binary Hierarchical Tree is used to classify the hyper spectral image. Results are validated with ground truth and accuracies are calculated.
Abstract: The acoustic and articulatory properties of fricative speech sounds are being studied using magnetic resonance imaging (MRI) and acoustic recordings from a single subject. Area functions were derived from a complete set of axial and coronal MR slices using two different methods: the Mermelstein technique and the Blum transform. Area functions derived from the two techniques were shown to differ significantly in some cases. Such differences will lead to different acoustic predictions and it is important to know which is the more accurate. The vocal tract acoustic transfer function (VTTF) was derived from these area functions for each fricative and compared with measured speech signals for the same fricative and same subject. The VTTFs for /f/ in two vowel contexts and the corresponding acoustic spectra are derived here; the Blum transform appears to show a better match between prediction and measurement than the Mermelstein technique.
Abstract: This paper presents a systematic approach for designing Unified Power Flow Controller (UPFC) based supplementary damping controllers for damping low frequency oscillations in a single-machine infinite-bus power system. Detailed investigations have been carried out considering the four alternatives UPFC based damping controller namely modulating index of series inverter (mB), modulating index of shunt inverter (mE), phase angle of series inverter (δB ) and phase angle of the shunt inverter (δE ). The design problem of the proposed controllers is formulated as an optimization problem and Real- Coded Genetic Algorithm (RCGA) is employed to optimize damping controller parameters. Simulation results are presented and compared with a conventional method of tuning the damping controller parameters to show the effectiveness and robustness of the proposed design approach.
Abstract: Stock portfolio selection is a classic problem in finance,
and it involves deciding how to allocate an institution-s or an individual-s
wealth to a number of stocks, with certain investment objectives
(return and risk). In this paper, we adopt the classical Markowitz
mean-variance model and consider an additional common realistic
constraint, namely, the cardinality constraint. Thus, stock portfolio
optimization becomes a mixed-integer quadratic programming problem
and it is difficult to be solved by exact optimization algorithms.
Chemical Reaction Optimization (CRO), which mimics the molecular
interactions in a chemical reaction process, is a population-based
metaheuristic method. Two different types of CRO, named canonical
CRO and Super Molecule-based CRO (S-CRO), are proposed to solve
the stock portfolio selection problem. We test both canonical CRO
and S-CRO on a benchmark and compare their performance under
two criteria: Markowitz efficient frontier (Pareto frontier) and Sharpe
ratio. Computational experiments suggest that S-CRO is promising
in handling the stock portfolio optimization problem.
Abstract: The Bulgarian natural expanded mineral obtained from Bentonite AD perlite (A deposit of "The Broken Mountain" for perlite mining, near by the village of Vodenicharsko, in the municipality of Djebel), was loaded with silver (as ion form - Ag+ 2 and 5 wt% by the incipient wetness impregnation method), and as atomic silver - Ag0 using Tollen-s reagent (silver mirror reaction). Some physicochemical characterization of the samples are provided via: DC arc-AES, XRD, DR-IR and UV-VIS. The aim of this work was to obtain and test the silver-loaded catalyst for ozone decomposition. So the samples loaded with atomic silver show ca. 80% conversion of ozone 20 minutes after the reaction start. Then conversion decreases to ca. 20 % but stay stable during the prolongation of time.
Abstract: The increase on the demand of IT resources diverts
the enterprises to use the cloud as a cheap and scalable solution.
Cloud computing promises achieved by using the virtual machine as a
basic unite of computation. However, the virtual machine pre-defined
settings might be not enough to handle jobs QoS requirements. This
paper addresses the problem of mapping jobs have critical start
deadlines to virtual machines that have predefined specifications.
These virtual machines hosted by physical machines and shared a
fixed amount of bandwidth. This paper proposed an algorithm that
uses the idle virtual machines bandwidth to increase the quote of other
virtual machines nominated as executors to urgent jobs. An algorithm
with empirical study have been given to evaluate the impact of the
proposed model on impatient jobs. The results show the importance
of dynamic bandwidth allocation in virtualized environment and its
affect on throughput metric.