Abstract: There is a growing body of evidence to support the
proposition of product take back for remanufacturing particularly
within the context of Extended Producer Responsibility (EPR).
Remanufacturing however presents challenges unlike that of
traditional manufacturing environments due to its high levels of
uncertainty which may further distract organizations from
considering its potential benefits. This paper presents a novel
modeling approach for evaluating the uncertainty of part failures
within the remanufacturing process and its impact on economic and
environmental performance measures. This paper presents both the
theoretical modeling approach and an example of its use in
application.
Abstract: The extract of milk thistle contains a mix of flavonolignans termed silymarine.. In order to analysis influence of growth regulators, genotype, explant and subculture on the accumulation of flavonolignans, a study was carried out by using two genotype (Budakalszi and Noor abad moghan cultivars), cotyledon and hypocotyle explants, solid media of MS supplemented by different combinations of two growth regulators; Kinetin (0.1, 1 mg/l) and 2,4-D (1, 2 mg/l). Seeds of the plant were germinated in MS media whitout growth regulators in growth chamber at 26°C and darkness condition. In order to callus induction, the culture media was supplemented whit different concentrations of 2,4-D and kinetin. Calli obtained from explants were sub-cultured four times into the fresh media of the first experiment. flavonoides was extracted from calli in four subcultures. The flavonoid components were determined by high- performance liquid choromatography (HPLC) and separated into Taxifolin, Silydianin+Silychristin, Silybin A+B and Isosilybin A+B. Results showed that with increasing callus age, increased accumulation of silybin A+B, but reduced Isosilybin A+B content. Highest accumulation of Taxifolin was observed at first calli. Calli produced from cotyledon explant of Budakalszi cultivar were superior for Silybin A+B, where calli from hypocotyl explant produced higher amount of Taxifolin and Silydianin+Silychristin. The best cultivar for Silymarin production in this study was Budakalszi cultivar. High amount of SBN A+B and TXF were obtained from hypocotil explant.
Abstract: Nurses in an Armed Force Hospital (AFH) expose to stronger stress than those in a civil hospital, especially in an emergency department (ED). Ironically, stresses of these nurses received few if any attention in academic research in the past. This study collects 227 samples from the emergency departments of four armed force hospitals in central and southern Taiwan. The research indicates that the top five stressors are a massive casualty event, delayed physician support, overloads of routine work, overloads of assignments, and annoying paper work. Excessive work loading was found to be the primary source of stress. Nurses who were perceived to have greater stress levels were more inclined to deploy emotion-oriented approaches and more likely to seek job rotations. Professional stressors and problem-oriented approaches were positively correlated. Unlike other local studies, this study concludes that the excessive work-loading is more stressful in an AFH.
Abstract: Extracellular ubiquitin in vivo effect on regenerative liver cells and liver histoarchitectonics has been studied. Experiments were performed on mature female white rats. Partial hepatectomy was made using the modified method of Higgins and Anderson. Standard histopathological assessment of liver tissue was used. Proliferative activity of hepatocytes was analyzed by colchicine mitotic index and immunohistochemical staining on ki67. We have found that regardless of number of injections and dose of extracellular ubiquitin liver histology has not been changed, so at tissue level no effect was observed. In vivo double injection of ubiquitin significantly decreases the mitotic activity at 32 hour point after partial hepatectomy. Thus, we can conclude that in vivo injected extracellular ubiquitin inhibits proliferative activity of hepatocytes in partially hepatectomyzed rats.
Abstract: Effect of high temperature exposure on properties of cement mortar containing municipal solid waste incineration (MSWI) bottom ash as partial natural aggregate replacement is analyzed in the paper. The measurements of mechanical properties, bulk density, matrix density, total open porosity, sorption and desorption isotherms are done on samples exposed to the temperatures of 20°C to 1000°C. TGA analysis is performed as well. Finally, the studied samples are analyzed by IR spectroscopy in order to evaluate TGA data.
Abstract: A method for solving linear and non-linear Goursat
problem is given by using the two-dimensional differential transform
method. The approximate solution of this problem is calculated in
the form of a series with easily computable terms and also the exact
solutions can be achieved by the known forms of the series solutions.
The method can easily be applied to many linear and non-linear
problems and is capable of reducing the size of computational work.
Several examples are given to demonstrate the reliability and the
performance of the presented method.
Abstract: Utilizing echoic intension and distribution from different organs and local details of human body, ultrasonic image can catch important medical pathological changes, which unfortunately may be affected by ultrasonic speckle noise. A feature preserving ultrasonic image denoising and edge enhancement scheme is put forth, which includes two terms: anisotropic diffusion and edge enhancement, controlled by the optimum smoothing time. In this scheme, the anisotropic diffusion is governed by the local coordinate transformation and the first and the second order normal derivatives of the image, while the edge enhancement is done by the hyperbolic tangent function. Experiments on real ultrasonic images indicate effective preservation of edges, local details and ultrasonic echoic bright strips on denoising by our scheme.
Abstract: This paper presents a novel method for data hiding based on neighborhood pixels information to calculate the number of bits that can be used for substitution and modified Least Significant Bits technique for data embedding. The modified solution is independent of the nature of the data to be hidden and gives correct results along with un-noticeable image degradation. The technique, to find the number of bits that can be used for data hiding, uses the green component of the image as it is less sensitive to human eye and thus it is totally impossible for human eye to predict whether the image is encrypted or not. The application further encrypts the data using a custom designed algorithm before embedding bits into image for further security. The overall process consists of three main modules namely embedding, encryption and extraction cm.
Abstract: In an open real-time system environment, the coexistence of different kinds of real-time and non real-time applications makes the system scheduling mechanism face new requirements and challenges. One two-level scheduling scheme of the open real-time systems is introduced, and points out that hard and soft real-time applications are scheduled non-distinctively as the same type real-time applications, the Quality of Service (QoS) cannot be guaranteed. It has two flaws: The first, it can not differentiate scheduling priorities of hard and soft real-time applications, that is to say, it neglects characteristic differences between hard real-time applications and soft ones, so it does not suit a more complex real-time environment. The second, the worst case execution time of soft real-time applications cannot be predicted exactly, so it is not worth while to cost much spending in order to assure all soft real-time applications not to miss their deadlines, and doing that may cause resource wasting. In order to solve this problem, a novel two-level real-time scheduling mechanism (including scheduling profile and scheduling algorithm) which adds the process of dealing with soft real-time applications is proposed. Finally, we verify real-time scheduling mechanism from two aspects of theory and experiment. The results indicate that our scheduling mechanism can achieve the following objectives. (1) It can reflect the difference of priority when scheduling hard and soft real-time applications. (2) It can ensure schedulability of hard real-time applications, that is, their rate of missing deadline is 0. (3) The overall rate of missing deadline of soft real-time applications can be less than 1. (4) The deadline of a non-real-time application is not set, whereas the scheduling algorithm that server 0 S uses can avoid the “starvation" of jobs and increase QOS. By doing that, our scheduling mechanism is more compatible with different types of applications and it will be applied more widely.
Abstract: In designing river intakes and diversion structures, it is paramount that the sediments entering the intake are minimized or, if possible, completely separated. Due to high water velocity, sediments can significantly damage hydraulic structures especially when mechanical equipment like pumps and turbines are used. This subsequently results in wasting water, electricity and further costs. Therefore, it is prudent to investigate and analyze the performance of lateral intakes affected by sediment control structures. Laboratory experiments, despite their vast potential and benefits, can face certain limitations and challenges. Some of these include: limitations in equipment and facilities, space constraints, equipment errors including lack of adequate precision or mal-operation, and finally, human error. Research has shown that in order to achieve the ultimate goal of intake structure design – which is to design longlasting and proficient structures – the best combination of sediment control structures (such as sill and submerged vanes) along with parameters that increase their performance (such as diversion angle and location) should be determined. Cost, difficulty of execution and environmental impacts should also be included in evaluating the optimal design. This solution can then be applied to similar problems in the future. Subsequently, the model used to arrive at the optimal design requires high level of accuracy and precision in order to avoid improper design and execution of projects. Process of creating and executing the design should be as comprehensive and applicable as possible. Therefore, it is important that influential parameters and vital criteria is fully understood and applied at all stages of choosing the optimal design. In this article, influential parameters on optimal performance of the intake, advantages and disadvantages, and efficiency of a given design are studied. Then, a multi-criterion decision matrix is utilized to choose the optimal model that can be used to determine the proper parameters in constructing the intake.
Abstract: Noise contamination in a magnetic resonance (MR)
image could occur during acquisition, storage, and transmission in
which effective filtering is required to avoid repeating the MR
procedure. In this paper, an iterative asymmetrical triangle fuzzy
filter with moving average center (ATMAVi filter) is used to reduce
different levels of salt and pepper noise in a brain MR image. Besides
visual inspection on filtered images, the mean squared error (MSE) is
used as an objective measurement. When compared with the median
filter, simulation results indicate that the ATMAVi filter is effective
especially for filtering a higher level noise (such as noise density =
0.45) using a smaller window size (such as 3x3) when operated
iteratively or using a larger window size (such as 5x5) when operated
non-iteratively.
Abstract: Photonic Crystal (PhC) based devices are being
increasingly used in multifunctional, compact devices in integrated
optical communication systems. They provide excellent
controllability of light, yet maintaining the small size required for
miniaturization. In this paper, the band gap properties of PhCs and
their typical applications in optical waveguiding are considered.
Novel PhC based applications such as nonlinear switching and
tapers are considered and simulation results are shown using the
accurate time-domain numerical method based on Finite Difference
Time Domain (FDTD) scheme. The suitability of these devices for
novel applications is discussed and evaluated.
Abstract: This research investigates risk factors for defective products in autoparts factories. Under a Bayesian framework, a generalized linear mixed model (GLMM) in which the dependent variable, the number of defective products, has a Poisson distribution is adopted. Its performance is compared with the Poisson GLM under a Bayesian framework. The factors considered are production process, machines, and workers. The products coded RT50 are observed. The study found that the Poisson GLMM is more appropriate than the Poisson GLM. For the production Process factor, the highest risk of producing defective products is Process 1, for the Machine factor, the highest risk is Machine 5, and for the Worker factor, the highest risk is Worker 6.
Abstract: Water pollution assessment problems arise frequently
in environmental science. In this research, a finite difference method
for solving the one-dimensional steady convection-diffusion equation
with variable coefficients is proposed; it is then used to optimize
water treatment costs.
Abstract: In the present paper; an experimental and numerical
investigations of drag reduction on a grooved circular cylinder have
been performed. The experiments were carried out in closed circuit
subsonic wind tunnel (TE44); the pressure distribution on the
cylinder was conducted using a TE44DPS differential pressure
scanner and the drag forces were measured using the TE81 balance.
The display unit is linked to a computer, loaded with DATASLIM
software for data analysis and logging of result. The numerical study
was performed using the code ANSYS FLUENT solving the
Reynolds Averaged Navier-Stokes (RANS) equations. The k-ε and k-
ω SST models were tested. The results obtained from the
experimental and numerical investigations have showed a reduction
in the drag when using longitudinal grooves namely 2 and 6 on the
cylinder.
Abstract: Stress analysis of functionally graded composite plates
composed of ceramic, functionally graded material and metal layers is
investigated using 3-D finite element method. In FGM layer, material
properties are assumed to be varied continuously in the thickness
direction according to a simple power law distribution in terms of the
volume fraction of a ceramic and metal. The 3-D finite element model
is adopted by using an 18-node solid element to analyze more
accurately the variation of material properties in the thickness
direction. Numerical results are compared for three types of materials.
In the analysis, the tensile and the compressive stresses are
summarized for various FGM thickness ratios, volume fraction
distributions, geometric parameters and mechanical loads.
Abstract: The advantage of solving the complex nonlinear
problems by utilizing fuzzy logic methodologies is that the
experience or expert-s knowledge described as a fuzzy rule base can
be directly embedded into the systems for dealing with the problems.
The current limitation of appropriate and automated designing of
fuzzy controllers are focused in this paper. The structure discovery
and parameter adjustment of the Branched T-S fuzzy model is
addressed by a hybrid technique of type constrained sparse tree
algorithms. The simulation result for different system model is
evaluated and the identification error is observed to be minimum.
Abstract: The purpose of this study was to suggest some optimal
waterfront scales around small rivers by reviewing domestic and
foreign survey reports about concept and relevant systems of the
ecological cities, analyzing the data collected from a survey about
scales and facilities of waterfront green zones around small rivers. The
questionnaire survey was conducted by sampling professional
designers, developers, the citizens living in the GunpoSanbon district
covered by no river system and the citizens living in such districts
covered by a river system. The question items were about need, uses,
scale and facilities of waterfront in common, and about satisfaction
with waterfront in case of citizen groups. In short, most of the subjects
in 5 groups preferred 10~20 wide waterfront green zone. And it is
judged that the results of this study about uses and facilities of the
waterfront green zone and its scales would provide for some basic data
useful to future waterfront green zone and urban development plans.
Abstract: Block replacement algorithms to increase hit ratio
have been extensively used in cache memory management. Among
basic replacement schemes, LRU and FIFO have been shown to be
effective replacement algorithms in terms of hit rates. In this paper,
we introduce a flexible stack-based circuit which can be employed in
hardware implementation of both LRU and FIFO policies. We
propose a simple and efficient architecture such that stack-based
replacement algorithms can be implemented without the drawbacks
of the traditional architectures. The stack is modular and hence, a set
of stack rows can be cascaded depending on the number of blocks in
each cache set. Our circuit can be implemented in conjunction with
the cache controller and static/dynamic memories to form a cache
system. Experimental results exhibit that our proposed circuit
provides an average value of 26% improvement in storage bits and its
maximum operating frequency is increased by a factor of two
Abstract: This paper proposes a novel feature extraction method,
based on Discrete Wavelet Transform (DWT) and K-L Seperability
(KLS), for the classification of Functional Data (FD). This method
combines the decorrelation and reduction property of DWT and the
additive independence property of KLS, which is helpful to extraction
classification features of FD. It is an advanced approach of the
popular wavelet based shrinkage method for functional data reduction
and classification. A theory analysis is given in the paper to prove the
consistent convergence property, and a simulation study is also done
to compare the proposed method with the former shrinkage ones. The
experiment results show that this method has advantages in improving
classification efficiency, precision and robustness.