Abstract: RF performance of SOI CMOS device has attracted
significant amount of interest recently. In order to improve RF
parameters, Strained Si/Relaxed Si0.8Ge0.2 investigated as a
replacement for Si technology .Enhancement of carrier mobility
associated with strain engineering makes Strained Si a promising
candidate for improving RF performance of CMOS technology.
From the simulation, the cut-off frequency is estimated to be 224
GHZ, whereas in SOI at similar bias is about 188 GHZ. Therefore,
Strained Si exhibits 19% improvement in cut-off frequency over
similar Si counterpart. In this paper, Ion/Ioff ratio is studied as one of
the key parameters in logic and digital application. Strained Si/SiGe
demonstrates better Ion/Ioff characteristic than SOI, in similar channel
length of 100 nm.Another important key analog figures of merit such
as Early Voltage (VEA) ,transconductance vs drain current (gm /Ids)
are studied. They introduce the efficiency of the devices to convert
dc power into ac frequency.
Abstract: In the Lost Foam Casting process, melting point
temperature of metal, as well as volume and rate of the foam
degradation have significant effect on the mold filling pattern.
Therefore, gas generation capacity and gas gap length are two
important parameters for modeling of mold filling time of the lost
foam casting processes. In this paper, the gas gap length at the liquidfoam
interface for a low melting point (aluminum) alloy and a high
melting point (Carbon-steel) alloy are investigated by the
photography technique. Results of the photography technique
indicated, that the gas gap length and the mold filling time are
increased with increased coating thickness and density of the foam.
The Gas gap lengths measured in aluminum and Carbon-steel,
depend on the foam density, and were approximately 4-5 and 25-60
mm, respectively. By using a new system, the gas generation
capacity for the aluminum and steel was measured. The gas
generation capacity measurements indicated that gas generation in
the Aluminum and Carbon-steel lost foam casting was about 50 CC/g
and 3200 CC/g polystyrene, respectively.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: A laboratory set-up was designed to survey the
effectiveness of UV/O3 advanced oxidation process (AOP) for the
removal of Carbaryl from polluted water in batch reactor. The study
was carried out by UV/O3 process for water samples containing 1 to
20 mg/L of Carbaryl in distilled water. Also the range of drinking
water resources adjusted in synthetic water and effects of contact
time, pH and Carbaryl concentration were studied. The residual
pesticide concentration was determined by applying high
performance liquid chromatography (HPLC). The results indicated
that increasing of retention time and pH, enhances pesticide removal
efficiency. The removal efficiency has been affected by pesticide
initial concentration. Samples with low pesticide concentration
showed a remarkable removal efficiency compared to the samples
with high pesticide concentration. AOP method showed the removal
efficiencies of 80% to 100%. Although process showed high
performance for removal of pesticide from water samples, this
process has different disadvantages including complication,
intolerability, difficulty of maintenance and equipmental and
structural requirements.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: Distillation column is one of the most common
operations in process industries and is while the most expensive unit
of the amount of energy consumption. Many ideas have been
presented in the related literature for optimizing energy consumption
in distillation columns. This paper studies the different heat
integration methods in a distillation column which separate Benzene,
Toluene, Xylene, and C9+. Three schemes of heat integration
including, indirect sequence (IQ), indirect sequence with forward
energy integration (IQF), and indirect sequence with backward
energy integration (IQB) has been studied in this paper. Using
shortcut method these heat integration schemes were simulated with
Aspen HYSYS software and compared with each other with
regarding economic considerations. The result shows that the energy
consumption has been reduced 33% in IQF and 28% in IQB in
comparison with IQ scheme. Also the economic result shows that the
total annual cost has been reduced 12% in IQF and 8% in IQB
regarding with IQ scheme. Therefore, the IQF scheme is most
economic than IQB and IQ scheme.
Abstract: In this paper, one-dimensional analysis of flow in a
single-stage gas gun is conducted. The compressible inviscid flow
equations are numerically solved by the second-order Roe TVD
method, by using moving boundaries. For investigation of real gas
effect the Noble-Able equation is applied. The numerical results are
compared with the experimental data to validate the numerical
scheme. The results show that with using the Noble-Able equation,
the muzzle velocity decreases.
Abstract: In the planning point of view, it is essential to have
mode choice, due to the massive amount of incurred in transportation
systems. The intercity travellers in Libya have distinct features, as
against travellers from other countries, which includes cultural and
socioeconomic factors. Consequently, the goal of this study is to
recognize the behavior of intercity travel using disaggregate models,
for projecting the demand of nation-level intercity travel in Libya.
Multinomial Logit Model for all the intercity trips has been
formulated to examine the national-level intercity transportation in
Libya. The Multinomial logit model was calibrated using nationwide
revealed preferences (RP) and stated preferences (SP) survey. The
model was developed for deference purpose of intercity trips (work,
social and recreational). The variables of the model have been
predicted based on maximum likelihood method. The data needed for
model development were obtained from all major intercity corridors
in Libya. The final sample size consisted of 1300 interviews. About
two-thirds of these data were used for model calibration, and the
remaining parts were used for model validation. This study, which is
the first of its kind in Libya, investigates the intercity traveler’s
mode-choice behavior. The intercity travel mode-choice model was
successfully calibrated and validated. The outcomes indicate that, the
overall model is effective and yields higher precision of estimation.
The proposed model is beneficial, due to the fact that, it is receptive
to a lot of variables, and can be employed to determine the impact of
modifications in the numerous characteristics on the need for various
travel modes. Estimations of the model might also be of valuable to
planners, who can estimate possibilities for various modes and
determine the impact of unique policy modifications on the need for
intercity travel.
Abstract: A composite made of plasma functionalized multiwall
carbon nanotubes (MWNTs) coated with SnO2 was synthesized by
sonochemical precipitation method. Thick layer of this
nanocomposite material was used as ethanol sensor at low
temperatures. The composite sensitivity for ethanol has increased by
a factor of 2 at room temperature and by a factor of 13 at 250°C in
comparison to that of pure SnO2. SEM image of nanocomposite
material showed MWNTs were embedded in SnO2 matrix and also a
higher surface area was observed in the presence of functionalized
MWNTs. Greatly improved sensitivity of the composite material to
ethanol can be attributed to new gas accessing passes through
MWNTs and higher specific surface area.
Abstract: In this paper, we propose a multiple objective optimization model with respect to portfolio selection problem for investors looking forward to diversify their equity investments in a number of equity markets. Based on Markowitz-s M-V model we developed a Fuzzy Mixed Integer Multi-Objective Nonlinear Programming Problem (FMIMONLP) to maximize the investors- future gains on equity markets, reach the optimal proportion of the budget to be invested in different equities. A numerical example with a comprehensive analysis on artificial data from several equity markets is presented in order to illustrate the proposed model and its solution method. The model performed well compared with the deterministic version of the model.
Abstract: The paper reports the preparation and photocatalytic
activity of ZnO/SnO2 and SnO2 nanoparticles. These nanoparticles
were synthesized by hydrothermal method. The products were
characterized by X-ray diffraction (XRD) and scanning electron
microscopy (SEM). Their grain sizes are about 50-100 nm. The
photocatalytic activities of these materials were investigated for
congo red removal from aqueous solution under UV light irradiation.
It was shown that the use of ZnO/SnO2 as photocatalyst have better
photocatalytic activity for degradation of congo red than SnO2 or
TiO2 (anatase, particle size: 30nm) alone.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: The selection of parents and breeding strategies for
the successful maize hybrid production will be facilitated by
heterotic groupings of parental lines and determination of combining
abilities of them. Fourteen maize inbred lines, used in maize breeding
programs in Iran, were crossed in a diallel mating design. The 91 F1
hybrids and the 14 parental lines were studied during two years at
four locations of Iran for investigation of combining ability of
gentypes for grain yield and to determine heterotic patterns among
germplasm sources, using both, the Griffing-s method and the biplot
approach for diallel analysis. The graphical representation offered by
biplot analysis allowed a rapid and effective overview of general
combining ability (GCA) and specific combining ability (SCA)
effects of the inbred lines, their performance in crosses, as well as
grouping patterns of similar genotypes. GCA and SCA effects were
significant for grain yield (GY). Based on significant positive GCA
effects, the lines derived from LSC could be used as parent in crosses
to increase GY. The maximum best- parent heterosis values and
highest SCA effects resulted from crosses B73 × MO17 and A679 ×
MO17 for GY. The best heterotic patterns were LSC × RYD, which
would be potentially useful in maize breeding programs to obtain
high-yielding hybrids in the same climate of Iran.
Abstract: Intravitreal injection (IVI) is the most common treatment for eye posterior segment diseases such as endopthalmitis, retinitis, age-related macular degeneration, diabetic retinopathy, uveitis, and retinal detachment. Most of the drugs used to treat vitreoretinal diseases, have a narrow concentration range in which they are effective, and may be toxic at higher concentrations. Therefore, it is critical to know the drug distribution within the eye following intravitreal injection. Having knowledge of drug distribution, ophthalmologists can decide on drug injection frequency while minimizing damage to tissues. The goal of this study was to develop a computer model to predict intraocular concentrations and pharmacokinetics of intravitreally injected drugs. A finite volume model was created to predict distribution of two drugs with different physiochemical properties in the rabbit eye. The model parameters were obtained from literature review. To validate this numeric model, the in vivo data of spatial concentration profile from the lens to the retina were compared with the numeric data. The difference was less than 5% between the numerical and experimental data. This validation provides strong support for the numerical methodology and associated assumptions of the current study.