Abstract: Evolution of one-dimensional electron system under
high-energy-density (HED) conditions is investigated, using the
principle of least-action and variational method. In a single-mode
modulation model, the amplitude and spatial wavelength of the
modulation are chosen to be general coordinates. Equations of motion
are derived by considering energy conservation and force balance.
Numerical results show that under HED conditions, electron density
modulation could exist. Time dependences of amplitude and
wavelength are both positively related to the rate of energy input.
Besides, initial loading speed has a significant effect on modulation
amplitude, while wavelength relies more on loading duration.
Abstract: Surveillance system is widely used in the traffic
monitoring. The deployment of cameras is moving toward a
ubiquitous camera (UbiCam) environment. In our previous study, a
novel service, called GPS-VT, was firstly proposed by incorporating
global positioning system (GPS) and visual tracking techniques for
the UbiCam environment. The first prototype is called GODTA
(GPS-based Moving Object Detection and Tracking Approach). For a
moving person carried GPS-enabled mobile device, he can be
tracking when he enters the field-of-view (FOV) of a camera
according to his real-time GPS coordinate. In this paper, GPS-VT
service is applied to the tracking of vehicles. The moving speed of a
vehicle is much faster than a person. It means that the time passing
through the FOV is much shorter than that of a person. Besides, the
update interval of GPS coordinate is once per second, it is
asynchronous with the frame rate of the real-time image. The above
asynchronous is worsen by the network transmission delay. These
factors are the main challenging to fulfill GPS-VT service on a
vehicle.In order to overcome the influence of the above factors, a
back-propagation neural network (BPNN) is used to predict the
possible lane before the vehicle enters the FOV of a camera. Then, a
template matching technique is used for the visual tracking of a target
vehicle. The experimental result shows that the target vehicle can be
located and tracking successfully. The success location rate of the
implemented prototype is higher than that of the previous GODTA.
Abstract: In the domain of machine vision, the
measurement of length is done using cameras where the
accuracy is directly proportional to the resolution of the
camera and inversely to the size of the object. Since most of
the pixels are wasted imaging the entire body as opposed to
just imaging the edges in a conventional system, a double
aperture system is constructed to focus on the edges to
measure at higher resolution. The paper discusses the
complexities and how they are mitigated to realize a practical
machine vision system.
Abstract: In this study, we are interested in the economic lot
scheduling problem (ELSP) that considers manufacturing of the
serviceable products and remanufacturing of the reworked products. In
this paper, we formulate a mathematical model for the ELSP with
reworks using the basic period approach. In order to solve this
problem, we propose a search algorithm to find the cyclic multiplier ki
of each product that can be cyclically produced for every ki basic
periods. This research also uses two heuristics to search for the optimal
production sequence of all lots and the optimal time length of the basic
period so as to minimize the average total cost. This research uses a
numerical example to show the effectiveness of our approach.
Abstract: Clearance in the joints of multibody mechanical
systems such as linkage mechanisms and robots is a main source of
vibration, and noise of the whole system, and wear of the joints
themselves. This clearance is an inevitable matter and cannot be
eliminated, since it allows the relative motion between joint
components and make them assemblage. This paper presents an
experimental verification of the obtained simulation results of a slider
– crank mechanism of one clearance revolute joint. The simulation
results are obtained with the aid of CAD and dynamic simulation
softwares, which is an effective method of simulation multibody
systems with clearance joints and have many advantages. The
comparison between both simulation and experimental results shows
that the simulation results are so close to the experimental ones which
proves the accuracy and efficiency of this method of modeling and
simulation of mechanical systems with clearance joints.
Abstract: Environmental accounting is a recent phenomenon in the modern jurisprudence. It may reflect the corporate governance mechanisms in line with the natural resources and environmental sound management and administration systems in any country of the world. It may be a corporate focused on the improving of the environmental quality. But it is often identified that it is ignored due to some reasons such as unconsciousness, lack of ethical education etc. At present, the world community is very much concerned about the state of the environmental accounting and auditing systems as it bears sustainability on the mother earth for our generations. It is one of the important tools for understanding on the role played by the natural environment in the economy. It provides adequate data which is highlighted both in the contribution of natural resources to economic well-being as well as the costs imposed by pollution or resource degradation. It can play a critical role as on be a part of the many international environmental organizations such as IUCN, WWF, PADELIA, WRI etc.; as they have been taking many initiatives for ensuring the environmental accouting for our competent survivals. The global state actors have already taken some greening accounting initiatives under the forum of the United Nations Division for Sustainable Dedevolpment, the United Nations Statistical Division, the United Nations Conference on Environment and development known as Earth Summit in Rio de Janeiro, Johannesburg Conference 2002 etc. This study will provide an overview of the environmental accounting education consisting of 25 respondents based on the primary and secondary sources.
Abstract: The groundwater is one of the main sources for
sustainability in the United Arab Emirates (UAE). Intensive
developments in Al-Ain area lead to increase water demand, which
consequently reduced the overall groundwater quantity in major
aquifers. However, in certain residential areas within Al-Ain, it has
been noticed that the groundwater level is rising, for example in
Sha-ab Al Askher area. The reasons for the groundwater rising
phenomenon are yet to be investigated. In this work, twenty four
seismic refraction profiles have been carried out along the study
pilot area; as well as field measurement of the groundwater level in
a number of available water wells in the area. The processed
seismic data indicated the deepest and shallowest groundwater
levels are 15m and 2.3 meters respectively. This result is greatly
consistent with the proper field measurement of the groundwater
level. The minimum detected value may be referred to perched
subsurface water which may be associated to the infiltration from
the surrounding water bodies such as lakes, and elevated farms. The
maximum values indicate the accurate groundwater level within the
study area. The findings of this work may be considered as a
preliminary help to the decision makers.
Abstract: Theoptimal extraction condition of dried Phaseolus
vulgaris powderwas studied. The three independent variables are raw
material concentration, shaking and centrifugaltime. The dependent
variables are both yield percentage of crude extract and alphaamylase
enzyme inhibition activity. The experimental design was
based on box-behnkendesign. Highest yield percentage of crude
extract could get from extraction condition at concentration of 1, 0,1,
concentration of 0.15 M ,extraction time for 2hour, and
separationtime for60 min. Moreover, the crude extract with highest
alpha-amylase enzyme inhibition activityoccurred by extraction
condition at concentration of 0.10 M, extraction time for 2 min, and
separation time for 45 min
Abstract: We propose a low-cost uniform analysis framework
allowing comparison of the strengths and weaknesses of the
bicycling experience within and between cities. A primary
component is an expedient, one-page mobility survey from which
mode share is calculated. The bicycle mode share of many cities
remains unknown, creating a serious barrier for both scientists and
policy makers aiming to understand and increase rates of bicycling.
Because of its low cost and expedience, this framework could be
replicated widely, uniformly filling the data gap. The framework has
been applied to 13 Central European cities with success. Data is
collected on multiple modes with specific questions regarding both
behavior and quality of travel experience. Individual preferences are
also collected, examining the conditions under which respondents
would change behavior to adopt more sustainable modes (bicycling
or public transportation). A broad analysis opportunity results,
intended to inform policy choices.
Abstract: Least Development Countries (LDC) like
Bangladesh, whose 25% revenue earning is achieved from Textile
export, requires producing less defective textile for minimizing
production cost and time. Inspection processes done on these
industries are mostly manual and time consuming. To reduce error
on identifying fabric defects requires more automotive and
accurate inspection process. Considering this lacking, this research
implements a Textile Defect Recognizer which uses computer
vision methodology with the combination of multi-layer neural
networks to identify four classifications of textile defects. The
recognizer, suitable for LDC countries, identifies the fabric defects
within economical cost and produces less error prone inspection
system in real time. In order to generate input set for the neural
network, primarily the recognizer captures digital fabric images by
image acquisition device and converts the RGB images into binary
images by restoration process and local threshold techniques.
Later, the output of the processed image, the area of the faulty
portion, the number of objects of the image and the sharp factor of
the image, are feed backed as an input layer to the neural network
which uses back propagation algorithm to compute the weighted
factors and generates the desired classifications of defects as an
output.
Abstract: The vehicle fleet of public transportation companies is often equipped with intelligent on-board passenger information systems. A frequently used but time and labor-intensive way for keeping the on-board controllers up-to-date is the manual update using different memory cards (e.g. flash cards) or portable computers. This paper describes a compression algorithm that enables data transmission using low bandwidth wireless radio networks (e.g. GPRS) by minimizing the amount of data traffic. In typical cases it reaches a compression rate of an order of magnitude better than that of the general purpose compressors. Compressed data can be easily expanded by the low-performance controllers, too.
Abstract: In this article we propose to model Net-banking
system by game theory. We adopt extensive game to model our web
application. We present the model in term of players and strategy.
We present UML diagram related the protocol game.
Abstract: Metal matrix composites have been increasingly used
as materials for components in automotive and aerospace industries
because of their improved properties compared with non-reinforced
alloys. During machining the selection of appropriate machining
parameters to produce job for desired surface roughness is of great
concern considering the economy of manufacturing process. In this
study, a surface roughness prediction model using fuzzy logic is
developed for end milling of Al-SiCp metal matrix composite
component using carbide end mill cutter. The surface roughness is
modeled as a function of spindle speed (N), feed rate (f), depth of cut
(d) and the SiCp percentage (S). The predicted values surface
roughness is compared with experimental result. The model predicts
average percentage error as 4.56% and mean square error as 0.0729.
It is observed that surface roughness is most influenced by feed rate,
spindle speed and SiC percentage. Depth of cut has least influence.
Abstract: Since the admission of Islam onto the Malay World in
16th century, the Malay culture began to grow in line with the
teachings of Islam as a guide of life. Mosque become a symbol of
Muslim communities, as well as the cultural values that have been
adapted represent the maturity and readiness of Malay Muslim in
manifest a lifestyle tradition into the community. Refinement of
ornament that used to take from Hindu-Buddhist beliefs before were
adopted and refined to the Islamic values based on the teachings of
al-Quran and as-Sunnah delivered a certain message to convey a
meaning to the observer. The main purpose of this paper is to analyze
the typology and classification of ornaments in Malaysia-s traditional
mosque as a channel to the community towards understanding of the
identity and also the framework of design thinking in ornaments
particularly to the urban mosques in Malaysia.
Abstract: One of the most challenges for hard surface cleaning product is to get rid of soap scum, a filmy sticky layer in the bathroom. The deposits of soap scum can be removed by using a proper surfactant solution with chelating agent. Unfortunately, the conventional chelating agent, ethylenediamine tetraacetic acid (EDTA), has low biodegradability, which can be tolerance in water resources and harmful to aquatic animal and microorganism. In this study, two biodegradable chelating agents, ethylenediamine disuccinic acid (EDDS) and glutamic acid diacetic acid (GLDA) were introduced as a replacement of EDTA. The result shows that using GLDA with amphoteric surfactant gave the highest equilibrium solubility of soap scum.
Abstract: This paper presents a new methodology to study power and energy consumption in mechatronic systems early in the development process. This new approach makes use of two modeling languages to represent and simulate embedded control software and electromechanical subsystems in the discrete event and continuous time domain respectively within a single co-model. This co-model enables an accurate representation of power and energy consumption and facilitates the analysis and development of both software and electro-mechanical subsystems in parallel. This makes the engineers aware of energy-wise implications of different design alternatives and enables early trade-off analysis from the beginning of the analysis and design activities.
Abstract: In this paper performance of Puma 560
manipulator is being compared for hybrid gradient descent
and least square method learning based ANFIS controller with
hybrid Genetic Algorithm and Generalized Pattern Search
tuned radial basis function based Neuro-Fuzzy controller.
ANFIS which is based on Takagi Sugeno type Fuzzy
controller needs prior knowledge of rule base while in radial
basis function based Neuro-Fuzzy rule base knowledge is not
required. Hybrid Genetic Algorithm with generalized Pattern
Search is used for tuning weights of radial basis function
based Neuro- fuzzy controller. All the controllers are checked
for butterfly trajectory tracking and results in the form of
Cartesian and joint space errors are being compared. ANFIS
based controller is showing better performance compared to
Radial Basis Function based Neuro-Fuzzy Controller but rule
base independency of RBF based Neuro-Fuzzy gives it an
edge over ANFIS
Abstract: This research aimed at investigating the Cr (III), Cd
(II) and Pb (II) removal efficiencies by using the newly synthesized
metal oxides/ polyethersulfone (PES), Al2O3/PES and ZrO2/PES,
membranes from synthetic wastewater and exploring fouling
mechanisms. A Comparative study between the removal efficiencies
of Cr (III), Cd (II) and Pb (II) from synthetic and natural wastewater
by using adsorption onto agricultural by products and the newly
synthesized Al2O3/PES and ZrO2/PES membranes was conducted to
assess the advantages and limitations of using the metal oxides/PES
membranes for heavy metals removal. The results showed that about
99 % and 88 % removal efficiencies were achieved by the tested
membranes for Pb (II) and Cr (III), respectively.
Abstract: Machining is an important manufacturing process used to produce a wide variety of metallic parts. Among various machining processes, turning is one of the most important one which is employed to shape cylindrical parts. In turning, the quality of finished product is measured in terms of surface roughness. In turn, surface quality is determined by machining parameters and tool geometry specifications. The main objective of this study is to simultaneously model and optimize machining parameters and tool geometry in order to improve the surface roughness for AISI1045 steel. Several levels of machining parameters and tool geometry specifications are considered as input parameters. The surface roughness is selected as process output measure of performance. A Taguchi approach is employed to gather experimental data. Then, based on signal-to-noise (S/N) ratio, the best sets of cutting parameters and tool geometry specifications have been determined. Using these parameters values, the surface roughness of AISI1045 steel parts may be minimized. Experimental results are provided to illustrate the effectiveness of the proposed approach.
Abstract: The resource-based view of the firm regards
knowledge as one of the most important organizational assets and a
key strategic resource that contributes unique value to organizations.
The acquisition, absorption and internalization of external
knowledge are central to an organization-s innovative capabilities.
This ability to evaluate, acquire and integrate new knowledge from
its environment is referred to as a firm-s absorptive capacity (AC).
This research in progress paper explores the link between interorganizational
Social Networks (SNs) and a firm-s Absorptive
Capacity (AC). Based on an in-depth literature survey of both
concepts, four propositions are proposed that explain the link
between AC and SNs. These propositions suggest that SNs are key
to a firm-s AC. A qualitative research method is proposed to test the
set of propositions in the next stage of this research.