Abstract: The paper aims at investigating influence of medium
capacity on linear adsorbed solute dispersion into chemically
heterogeneous fixed beds. A discrete chemical heterogeneity
distribution is considered in the one-dimensional advectivedispersive
equation. The partial differential equation is solved using
finite volumes method based on the Adam-Bashforth algorithm.
Increased dispersion is estimated by comparing breakthrough curves
second order moments and keeping identical hydrodynamic
properties. As a result, dispersion increase due to chemical
heterogeneity depends on the column size and surprisingly on the
solid capacity. The more intense capacity is, the more important
solute dispersion is. Medium length which is known to favour this
effect vanishing according to the linear adsorption in fixed bed seems
to create nonmonotonous variation of dispersion because of the
heterogeneity. This nonmonotonous behaviour is also favoured by
high capacities.
Abstract: This paper presents PSS (Power system stabilizer) design based on optimal fuzzy PID (OFPID). OFPID based PSS design is considered for single-machine power systems. The main motivation for this design is to stabilize or to control low-frequency oscillation on power systems. Firstly, describing the linear PID control then to combine this PID control with fuzzy logic control mechanism. Finally, Fuzzy PID parameters (Kp. Kd, KI, Kupd, Kui) are tuned by Genetic Algorthm (GA) to reach optimal global stability. The effectiveness of the proposed PSS in increasing the damping of system electromechanical oscillation is demonstrated in a one-machine-infinite-bus system
Abstract: The hybridisation of genetic algorithm with heuristics has been shown to be one of an effective way to improve its performance. In this work, genetic algorithm hybridised with four heuristics including a new heuristic called neighbourhood improvement were investigated through the classical travelling salesman problem. The experimental results showed that the proposed heuristic outperformed other heuristics both in terms of quality of the results obtained and the computational time.
Abstract: The presence of chemical bonding between functionalized carbon nanotubes and matrix in carbon nanotube reinforced composites is modeled by elastic beam elements representing covalent bonding characteristics. Neglecting other reinforcing mechanisms in the composite such as relatively weak interatomic Van der Waals forces, this model shows close results to the Rule of Mixtures model-s prediction for effective Young-s modulus of a Representative Volume Element of composite for small volume fractions (~1%) and high aspect ratios (L/D>200) of CNTs.
Abstract: In this paper the application of rule mining in order to
review the effective factors on supplier selection is reviewed in the
following three sections 1) criteria selecting and information
gathering 2) performing association rule mining 3) validation and
constituting rule base. Afterwards a few of applications of rule base
is explained. Then, a numerical example is presented and analyzed
by Clementine software. Some of extracted rules as well as the
results are presented at the end.
Abstract: The aerodynamic stall control of a baseline 13-percent
thick NASA GA(W)-2 airfoil using a synthetic jet actuator (SJA) is
presented in this paper. Unsteady Reynolds-averaged Navier-Stokes
equations are solved on a hybrid grid using a commercial software to
simulate the effects of a synthetic jet actuator located at 13% of the
chord from the leading edge at a Reynolds number Re = 2.1x106 and
incidence angles from 16 to 22 degrees. The experimental data for the
pressure distribution at Re = 3x106 and aerodynamic coefficients at
Re = 2.1x106 (angle of attack varied from -16 to 22 degrees) without
SJA is compared with the computational fluid dynamic (CFD)
simulation as a baseline validation. A good agreement of the CFD
simulations is obtained for aerodynamic coefficients and pressure
distribution.
A working SJA has been integrated with the baseline airfoil and
initial focus is on the aerodynamic stall control at angles of attack
from 16 to 22 degrees. The results show a noticeable improvement in
the aerodynamic performance with increase in lift and decrease in
drag at these post stall regimes.
Abstract: Providing authentication for the messages exchanged
between group members in addition to confidentiality is an important
issue in Secure Group communication. We develop a protocol for
Secure Authentic Communication where we address authentication
for the group communication scheme proposed by Blundo et al.
which only provides confidentiality. Authentication scheme used is a
multiparty authentication scheme which allows all the users in the
system to send and receive messages simultaneously. Our scheme is
secure against colluding malicious parties numbering fewer than k.
Abstract: The motion planning technique described in this paper has been developed to eliminate or reduce the residual vibrations of belt-driven rotary platforms, while maintaining unchanged the motion time and the total angular displacement of the platform. The proposed approach is based on a suitable choice of the motion command given to the servomotor that drives the mechanical device; this command is defined by some numerical coefficients which determine the shape of the displacement, velocity and acceleration profiles. Using a numerical optimization technique, these coefficients can be changed without altering the continuity conditions imposed on the displacement and its time derivatives at the initial and final time instants. The proposed technique can be easily and quickly implemented on an actual device, since it requires only a simple modification of the motion command profile mapped in the memory of the electronic motion controller.
Abstract: It is well known that metallic particles reduce the
reliability of Gas-Insulated Substation (GIS) equipments by initiating
partial discharge (PDs) that can lead to breakdown and complete
failure of GIS. This paper investigates the characteristics of PDs
caused by metallic particle adhering to the solid spacer. The PD
detection and measurement were carried out by using IEC 60270
method with particles of different sizes and at different positions on
the spacer surface. The results show that a particle of certain size at
certain position possesses a unique PD characteristic as compared to
those caused by particles of different sizes and/or at different
positions. Therefore PD characteristics may be useful for the particle
size and position identification.
Abstract: Today technological process makes possible surface
control of producing parts which is needful for product quality
guarantee. Geometrical structure of part surface includes form,
proportion, accuracy to shape, accuracy to size, alignment and
surface topography (roughness, waviness, etc.). All these parameters
are dependence at technology, production machine parameters,
material properties, but also at human, etc. Every parameters
approves at total part accuracy, it is means at accuracy to shape. One
of the most important accuracy to shape element is roundness. This
paper will be deals by comparison of roughness deviations at
coordination measuring machines and at special single purpose
machines. Will describing measuring by discreet method
(discontinuous) and scanning method (continuous) at coordination
measuring machines and confrontation with reference method using
at single purpose machines.
Abstract: We introduce an extended resource leveling model that abstracts real life projects that consider specific work ranges for each resource. Contrary to traditional resource leveling problems this model considers scarce resources and multiple objectives: the minimization of the project makespan and the leveling of each resource usage over time. We formulate this model as a multiobjective optimization problem and we propose a multiobjective genetic algorithm-based solver to optimize it. This solver consists in a two-stage process: a main stage where we obtain non-dominated solutions for all the objectives, and a postprocessing stage where we seek to specifically improve the resource leveling of these solutions. We propose an intelligent encoding for the solver that allows including domain specific knowledge in the solving mechanism. The chosen encoding proves to be effective to solve leveling problems with scarce resources and multiple objectives. The outcome of the proposed solvers represent optimized trade-offs (alternatives) that can be later evaluated by a decision maker, this multi-solution approach represents an advantage over the traditional single solution approach. We compare the proposed solver with state-of-art resource leveling methods and we report competitive and performing results.
Abstract: Development of a Robust Supply Chain for Dynamic
Operating Environment as we move further into the twenty first
century, organisations are under increasing pressure to deliver a high
product variation at a reasonable cost without compromise in quality.
In a number of cases this will take the form of a customised or high
variety low volume manufacturing system that requires prudent
management of resources, among a number of functions, to achieve
competitive advantage. Purchasing and Supply Chain management is
one of such function and due to the substantial interaction with
external elements needs to be strategically managed. This requires a
number of primary and supporting tools that will enable the
appropriate decisions to be made rapidly. This capability is
especially vital in a dynamic environment as it provides a pivotal role
in increasing the profit margin of the product. The management of
this function can be challenging by itself and even more for Small
and Medium Enterprises (SMEs) due to the limited resources and
expertise available at their disposal.
This paper discusses the development of tools and concepts
towards effectively managing the purchasing and supply chain
function. The developed tools and concepts will provide a cost
effective way of managing this function within SMEs. The paper
further shows the use of these tools within Contechs, a manufacturer
of luxury boat interiors, and the associated benefits achieved as a
result of this implementation. Finally a generic framework towards
use in such environments is presented.
Abstract: Directive 2009/28/CE establishes, as obligatory objective, a share of renewable energies on energetic consumption of 20%, in European Union, in 2020 However, such European normative gives freedom to member states in the selection of the renewable promotion mechanism that allows them to obtain that objective. In this paper, we analyze the main characteristics of the promotion mechanisms of renewable energy used in the countries that shape the Electricity Iberian Market (Spain and Portugal) and the results in employment. The importance of these countries is given by the great increasing of the renewable energies which suppose a share higher than 30% of the overall generation in 2010. Therefore, this research paper can serve as the basis for the learning of other countries with regard to the main advantages that entail the use of a feed-in tariff system.
Abstract: Combined conduction-free convection heat transfer in
vertical eccentric annuli is numerically investigated using a finitedifference
technique. Numerical results, representing the heat transfer
parameters such as annulus walls temperature, heat flux, and heat
absorbed in the developing region of the annulus, are presented for a
Newtonian fluid of Prandtl number 0.7, fluid-annulus radius ratio 0.5,
solid-fluid thermal conductivity ratio 10, inner and outer wall
dimensionless thicknesses 0.1 and 0.2, respectively, and
dimensionless eccentricities 0.1, 0.3, 0.5, and 0.7. The annulus walls
are subjected to thermal boundary conditions, which are obtained by
heating one wall isothermally whereas keeping the other wall at inlet
fluid temperature. In the present paper, the annulus heights required
to achieve thermal full development for prescribed eccentricities are
obtained. Furthermore, the variation in the height of thermal full
development as function of the geometrical parameter, i.e.,
eccentricity is also investigated.
Abstract: The aim of the current work is to present a comparison among three popular optimization methods in the inverse elastostatics problem (IESP) of flaw detection within a solid. In more details, the performance of a simulated annealing, a Hooke & Jeeves and a sequential quadratic programming algorithm was studied in the test case of one circular flaw in a plate solved by both the boundary element (BEM) and the finite element method (FEM). The proposed optimization methods use a cost function that utilizes the displacements of the static response. The methods were ranked according to the required number of iterations to converge and to their ability to locate the global optimum. Hence, a clear impression regarding the performance of the aforementioned algorithms in flaw identification problems was obtained. Furthermore, the coupling of BEM or FEM with these optimization methods was investigated in order to track differences in their performance.
Abstract: The industrial process of the sugar cane crystallization produces a residual that still contains a lot of soluble sucrose and the objective of the factory is to improve its extraction. Therefore, there are substantial losses justifying the search for the optimization of the process. Crystallization process studied on the industrial site is based on the “three massecuites process". The third step of this process constitutes the final stage of exhaustion of the sucrose dissolved in the mother liquor. During the process of the third step of crystallization (Ccrystallization), the phase that is studied and whose control is to be improved, is the growing phase (crystal growth phase). The study of this process on the industrial site is a problem in its own. A control scheme is proposed to improve the standard PID control law used in the factory. An auto-tuning PID controller based on instantaneous linearization of a neural network is then proposed.
Abstract: The goal of speech parameterization is to extract the relevant information about what is being spoken from the audio signal. In speech recognition systems Mel-Frequency Cepstral Coefficients (MFCC) and Relative Spectral Mel-Frequency Cepstral Coefficients (RASTA-MFCC) are the two main techniques used. It will be shown in this paper that it presents some modifications to the original MFCC method. In our work the effectiveness of proposed changes to MFCC called Modified Function Cepstral Coefficients (MODFCC) were tested and compared against the original MFCC and RASTA-MFCC features. The prosodic features such as jitter and shimmer are added to baseline spectral features. The above-mentioned techniques were tested with impulsive signals under various noisy conditions within AURORA databases.
Abstract: The experimental design was 4 x 5 factorial with three
replications in fully controlled research greenhouse in Department of
Soil Sciences and Plant Nutrition, Faculty of Agriculture, University
of Selcuk in the year of 2009. Determination of tolerant chickpea
genotypes to drought was made in the research. Additionally,
sophisticated effects of drought on plant growth and development,
biochemical and physical properties or physical defense mechanisms
were presented. According to the results, the primary genotypes were
Ilgın YP (0.0063 g/gh) for leaf water capacity, 22235 70.44(%) for
relative water content, 22159 (82.47%) for real water content,
22159 (5.03 mg/l) for chlorophyll a+b, Ilgın YP (125.89 nmol
H2O2.dak-1/ mg protein-1) for peroxidase, Yunak YP (769.67
unit/ mg protein-1) for superoxide dismutase, Seydişehir YP
(16.74 μg.TA-1) for proline, Gökçe (80.01 nmol H2O2.dak-1/ mg
protein-1) for catalase. Consequently, all the genotypes
increased their enzyme activity depending on the increasing of
drought stress consider with the effects of drought stress on leaf
enzyme activity. Chickpea genotypes are increasing enzyme
activity against to drought stress.
Abstract: Today-s children, who are born into a more colorful,
more creative, more abstract and more accessible communication
environment than their ancestors as a result of dizzying advances in
technology, have an interesting capacity to perceive and make sense
of the world. Millennium children, who live in an environment where
all kinds of efforts by marketing communication are more intensive
than ever are, from their early childhood on, subject to all kinds of
persuasive messages. As regards advertising communication, it
outperforms all the other marketing communication efforts in
creating little consumer individuals and, as a result of processing of
codes and signs, plays a significant part in building a world of seeing,
thinking and understanding for children. Children who are raised with
metaphorical expressions such as tales and riddles also meet that fast
and effective meaning communication in advertisements.
Children-s perception of metaphors, which help grasp the “product
and its promise" both verbally and visually and facilitate association
between them is the subject of this study. Stimulating and activating
imagination, metaphors have unique advantages in promoting the
product and its promise especially in regard to print advertisements,
which have certain limitations. This study deals comparatively with
both literal and metaphoric versions of print advertisements
belonging to various product groups and attempts to discover to what
extent advertisements are liked, recalled, perceived and are
persuasive. The sample group of the study, which was conducted in
two elementary schools situated in areas that had different socioeconomic
features, consisted of children aged 12.
Abstract: We have proposed an information filtering system
using index word selection from a document set based on the
topics included in a set of documents. This method narrows
down the particularly characteristic words in a document set
and the topics are obtained by Sparse Non-negative Matrix
Factorization. In information filtering, a document is often
represented with the vector in which the elements correspond
to the weight of the index words, and the dimension of the
vector becomes larger as the number of documents is
increased. Therefore, it is possible that useless words as index
words for the information filtering are included. In order to
address the problem, the dimension needs to be reduced. Our
proposal reduces the dimension by selecting index words
based on the topics included in a document set. We have
applied the Sparse Non-negative Matrix Factorization to the
document set to obtain these topics. The filtering is carried out
based on a centroid of the learning document set. The centroid
is regarded as the user-s interest. In addition, the centroid is
represented with a document vector whose elements consist of
the weight of the selected index words. Using the English test
collection MEDLINE, thus, we confirm the effectiveness of
our proposal. Hence, our proposed selection can confirm the
improvement of the recommendation accuracy from the other
previous methods when selecting the appropriate number of
index words. In addition, we discussed the selected index
words by our proposal and we found our proposal was able to
select the index words covered some minor topics included in
the document set.