Abstract: Within Rapid Prototyping technologies are used many
types of materials. Many of them are recyclable but there are still as
plastic like, so practically they do not degrade in the landfill.
Polylactic acid (PLA) is one of the special plastic materials, which
are biodegradable and available for 3D printing within Fused
Deposition Modeling (FDM) technology. The question is, if the
mechanical properties of produced models are comparable to similar
technical plastic materials which are usual for prototype production.
Presented paper shows the experiments results for tensile strength
measurements for specimens prepared with different 3D printer
settings and model orientation. Paper contains also the comparison of
tensile strength values with values measured on specimens produced
by conventional technologies as injection moulding.
Abstract: Broiler slaughter waste has become a major source of
pollution throughout the world. Utilization of broiler slaughter waste
by dry rendering process produced Rendered Chicken Oil (RCO), a
cheap raw material for biodiesel production and Carcass Meal a feed
ingredient for pets and fishes. Conversion of RCO into biodiesel may
open new vistas for generating wealth from waste besides controlling
the major havoc of environmental pollution. A two-step process to
convert RCO to good quality Biodiesel was invented. Acid catalysed
esterification of FFA followed by base catalysed transesterification of
triglycerides was carried out after meticulously standardizing the
methanol molar ratio, catalyst concentration, reaction temperature,
and reaction time to obtain the maximum biodiesel yield of 97.62%
and lowest glycerol yield of 6.96%. RCO biodiesel blend was tested
in a CRDI diesel engine. The results revealed that the blending of
commercial diesel with 20% RCO biodiesel (B20) lead to less engine
wear, a quieter engine and better fuel economy. The better lubricating
qualities of RCO B20 prevented over heating of engine, which
prolongs the engine life. RCO B20 can reduce the import of crude oil
and substantially reduce the engine emissions as proved by
significantly lower smoke levels, thus mitigating climatic changes.
Abstract: The main cause of Alzheimer disease (AD) was
believed to be mainly due to the accumulation of free radicals owing
to oxidative stress (OS) in brain tissue. The mechanism of the
neurotoxicity of Aluminum chloride (AlCl3) induced AD in
hippocampus Albino wister rat brain tissue, the curative & the
protective effects of Lipidium sativum group (LS) water extract were
assessed after 8 weeks by attenuated total reflection spectroscopy
ATR-IR and histologically by light microscope. ATR-IR results
revealed that the membrane phospholipid undergo free radical
attacks, mediated by AlCl3, primary affects the polyunsaturated fatty
acids indicated by the increased of the olefinic -C=CH sub-band area
around 3012 cm-1 from the curve fitting analysis. The narrowing in
the half band width (HBW) of the sνCH2 sub-band around 2852 cm-1
due to Al intoxication indicates the presence of trans form fatty acids
rather than gauch rotomer. The degradation of hydrocarbon chain to
shorter chain length, increasing in membrane fluidity, disorder, and
decreasing in lipid polarity in AlCl3 group indicated by the detected
changes in certain calculated area ratios compared to the control.
Administration of LS was greatly improved these parameters
compared to the AlCl3 group. Al influences the Aβ aggregation and
plaque formation, which in turn interferes to and disrupts the
membrane structure. The results also showed a marked increase in
the β-parallel and antiparallel structure, that characterize the Aβ
formation in Al-induced AD hippocampal brain tissue, indicated by
the detected increase in both amide I sub-bands around 1674, 1692
cm-1. This drastic increase in Aβ formation was greatly reduced in the
curative and protective groups compared to the AlCl3 group and
approached nearly the control values. These results supported too by
the light microscope. AlCl3 group showed significant marked
degenerative changes in hippocampal neurons. Most cells appeared
small, shrieked and deformed. Interestingly, the administration of LS
in curative and protective groups markedly decreases the amount of
degenerated cells compared to the non-treated group. In addition, the
intensity of congo red stained cells was decreased. Hippocampal
neurons looked more/or less similar to those of control. This study showed a promising therapeutic effect of Lipidium
sativum group (LS) on AD rat model that seriously overcome the
signs of oxidative stress on membrane lipid and restore the protein
misfolding.
Abstract: According to IR, 13C and 1H NMR, APT, 1D NOE,
2D heteronuclear 1H/13C HSQC and 2D DOSY experiments the main
chemical constituent of high-molecular preparations from Symphytum
asperum, S. caucasicum, S. officinale and Anchusa italica
(Boraginaceae) was found to be caffeic acid-derived polyether,
namely poly[3-(3,4-dihydroxyphenyl)glyceric acid] (PDPGA) or
poly[oxy-1-carboxy-2-(3,4-dihydroxyphenyl)ethylene]. Most
carboxylic groups of this polymer of A. italica are methylated.
Abstract: Millions of girls are forcibly married during the
transitional period between puberty and adulthood. At a stage of
vulnerability cultural practices, religious rights and social standards
place her in a position where she is catapult into womanhood. An
advocate against forced child marriage could argue that child rights,
cultural rights, religious rights, right to marry, right to life, right to
health, right to education, right to be free from slavery, right to be
free from torture, right to consent to marriage are all violated by the
practice of child marriage. The author is this advocate and this paper
will present how some of these rights are violated and establish the
need for change.
Abstract: The plastic industry plays very important role in the
economy of any country. It is generally among the leading share of
the economy of the country. Since metals and their alloys are very
rarely available on the earth. Therefore, to produce plastic products
and components, which finds application in many industrial as well
as household consumer products is beneficial. Since 50% plastic
products are manufactured by injection moulding process. For
production of better quality product, we have to control quality
characteristics and performance of the product. The process
parameters plays a significant role in production of plastic, hence the
control of process parameter is essential. In this paper the effect of
the parameters selection on injection moulding process has been
described. It is to define suitable parameters in producing plastic
product. Selecting the process parameter by trial and error is neither
desirable nor acceptable, as it is often tends to increase the cost and
time. Hence, optimization of processing parameter of injection
moulding process is essential. The experiments were designed with
Taguchi’s orthogonal array to achieve the result with least number of
experiments. Plastic material polypropylene is studied. Tensile
strength test of material is done on universal testing machine, which
is produced by injection moulding machine. By using Taguchi
technique with the help of MiniTab-14 software the best value of
injection pressure, melt temperature, packing pressure and packing
time is obtained. We found that process parameter packing pressure
contribute more in production of good tensile plastic product.
Abstract: Direct Torque Control (DTC) is an AC drive control
method especially designed to provide fast and robust responses. In
this paper a progressive algorithm for direct torque control of threephase
induction drive system supplied by photovoltaic arrays using
voltage source inverter to control motor torque and flux with
maximum power point tracking at different level of insolation is
presented. Experimental results of the new DTC method obtained by
an experimental rapid prototype system for drives are presented.
Simulation and experimental results confirm that the proposed system
gives quick, robust torque and speed responses at constant switching
frequencies.
Abstract: A method of effective planning and control of
industrial facility energy consumption is offered. The method allows
optimally arranging the management and full control of complex
production facilities in accordance with the criteria of minimal
technical and economic losses at the forecasting control. The method
is based on the optimal construction of the power efficiency
characteristics with the prescribed accuracy. The problem of optimal
designing of the forecasting model is solved on the basis of three
criteria: maximizing the weighted sum of the points of forecasting
with the prescribed accuracy; the solving of the problem by the
standard principles at the incomplete statistic data on the basis of
minimization of the regularized function; minimizing the technical
and economic losses due to the forecasting errors.
Abstract: This article proposes a hybrid algorithm for spectrum
allocation in cognitive radio networks based on the algorithms
Analytical Hierarchical Process (AHP) and Technique for Order of
Preference by Similarity to Ideal Solution (TOPSIS) to improve the
performance of the spectrum mobility of secondary users in cognitive
radio networks. To calculate the level of performance of the proposed algorithm a
comparative analysis between the proposed AHP-TOPSIS, Grey
Relational Analysis (GRA) and Multiplicative Exponent Weighting
(MEW) algorithm is performed. Four evaluation metrics are used.
These metrics are accumulative average of failed handoffs,
accumulative average of handoffs performed, accumulative average
of transmission bandwidth, and accumulative average of the
transmission delay. The results of the comparison show that AHP-TOPSIS Algorithm
provides 2.4 times better performance compared to a GRA Algorithm
and, 1.5 times better than the MEW Algorithm.
Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: Unemployment among the youth is a significant
problem in South Africa. Large corporations and the public sector
simply cannot create enough jobs. Too many youths in South Africa
currently do not consider entrepreneurship as an option in order to
become independent. Unlike the youth of the Netherlands, South
African youth prefer to find employment in the public or private
sector. The Netherlands has a much lower unemployment rate than
South Africa and the Dutch are generally very entrepreneurial. From
early on, entrepreneurship is considered a desirable career option in
the Netherlands. The purpose of this study was to determine whether
there is a difference in the perceptions of some Dutch and South
African students in terms of unemployment and entrepreneurship.
Questionnaires were distributed to students at the North West
University's Vaal Triangle campus in Vanderbijlpark in Gauteng,
South Africa and the Technical University of Delft in the
Netherlands. A descriptive statistical analysis approach was followed
and the means for the independent questions were calculated. The
results demonstrate that the Dutch students are not as concerned
about unemployment after completion of their studies as this is not as
significant a problem as it is in South Africa. Both groups had
positive responses towards the posed questions, but the South African
group felt more strongly about the issues. Both groups of students felt
that there was a need for more practical entrepreneurship training.
The South African education system should focus on practical
entrepreneurship training from a young age.
Abstract: Globally, many women are still disadvantaged when it
comes to business opportunities. Entrepreneurship development
programs, specifically designed to assist women entrepreneurs, are
assisting in solving this problem to a certain extent. The purpose of
this study is to identify the factors that motivate females to start their
own business. Females, from three different groups (2013, 2014 and
2015), who were all enrolled in a short learning program specifically
designed for women in early start-up stage or intending to start a
business, were asked what motivated them to start a business. The
results indicated that, from all three groups, the majority of the
women wanted to start a business to be independent and have
freedom and to add towards a social goal. The results further
indicated that in general, women would enter into entrepreneurship
activity due to pull factors rather than push factors.
Abstract: A Multi-dimensional computational fluid dynamics
(CFD) two-phase model was developed with the aim to simulate
the in-core coolant circuit of a pressurized heavy water reactor
(PHWR) of a commercial nuclear power plant (NPP). Due to the
fact that this PHWR is a Reactor Pressure Vessel type (RPV),
three-dimensional (3D) detailed modelling of the large reservoirs of
the RPV (the upper and lower plenums and the downcomer) were
coupled with an in-house finite volume one-dimensional (1D) code
in order to model the 451 coolant channels housing the nuclear fuel.
Regarding the 1D code, suitable empirical correlations for taking into
account the in-channel distributed (friction losses) and concentrated
(spacer grids, inlet and outlet throttles) pressure losses were used.
A local power distribution at each one of the coolant channels
was also taken into account. The heat transfer between the coolant
and the surrounding moderator was accurately calculated using a
two-dimensional theoretical model. The implementation of subcooled
boiling and condensation models in the 1D code along with the use
of functions for representing the thermal and dynamic properties of
the coolant and moderator (heavy water) allow to have estimations
of the in-core steam generation under nominal flow conditions for a
generic fission power distribution. The in-core mass flow distribution
results for steady state nominal conditions are in agreement with the
expected from design, thus getting a first assessment of the coupled
1/3D model. Results for nominal condition were compared with
those obtained with a previous 1/3D single-phase model getting more
realistic temperature patterns, also allowing visualize low values of
void fraction inside the upper plenum. It must be mentioned that the
current results were obtained by imposing prescribed fission power
functions from literature. Therefore, results are showed with the aim
of point out the potentiality of the developed model.
Abstract: In order to be competitive, companies have to reduce
their production costs while meeting increasing quality requirements.
Therefore, companies try to plan their assembly processes as detailed
as possible. However, increasing product individualization leading to
a higher number of variants, smaller batch sizes and shorter product
life cycles raise the question to what extent the effort of detailed
planning is still justified. An important approach in this field of
research is the concept of determining the economic planning depth
for assembly process planning based on production specific
influencing factors. In this paper first solution hypotheses as well as a
first draft of the resulting method will be presented.
Abstract: Radio Frequency Identification (RFID) has become a
key technology in the emerging concept of Internet of Things (IoT).
Naturally, business applications would require the deployment of
various RFID systems developed by different vendors that use
different data formats and structures. This heterogeneity poses a
challenge in developing real-life IoT systems with RFID, as
integration is becoming very complex and challenging. Semantic
integration is a key approach to deal with this challenge. To do so,
ontology for RFID systems need to be developed in order to
annotated semantically RFID systems, and hence, facilitate their
integration. Accordingly, in this paper, we propose ontology for
RFID systems. The proposed ontology can be used to semantically
enrich RFID systems, and hence, improve their usage and reasoning.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: Large-scale machine tools for the manufacturing of
large work pieces, e.g. blades, casings or gears for wind turbines,
feature pose-dependent dynamic behavior. Small structural damping
coefficients lead to long decay times for structural vibrations that
have negative impacts on the production process. Typically, these
vibrations are handled by increasing the stiffness of the structure by
adding mass. This is counterproductive to the needs of sustainable
manufacturing as it leads to higher resource consumption both in
material and in energy. Recent research activities have led to higher
resource efficiency by radical mass reduction that is based on controlintegrated
active vibration avoidance and damping methods. These
control methods depend on information describing the dynamic
behavior of the controlled machine tools in order to tune the
avoidance or reduction method parameters according to the current
state of the machine. This paper presents the appearance, consequences and challenges
of the pose-dependent dynamic behavior of lightweight large-scale
machine tool structures in production. It starts with the theoretical
introduction of the challenges of lightweight machine tool structures
resulting from reduced stiffness. The statement of the pose-dependent
dynamic behavior is corroborated by the results of the experimental
modal analysis of a lightweight test structure. Afterwards, the
consequences of the pose-dependent dynamic behavior of lightweight
machine tool structures for the use of active control and vibration
reduction methods are explained. Based on the state of the art of
pose-dependent dynamic machine tool models and the modal
investigation of an FE-model of the lightweight test structure, the
criteria for a pose-dependent model for use in vibration reduction are
derived. The description of the approach for a general posedependent
model of the dynamic behavior of large lightweight
machine tools that provides the necessary input to the aforementioned
vibration avoidance and reduction methods to properly tackle
machine vibrations is the outlook of the paper.
Abstract: The importance of agribusiness development is
proved in accordance with the trends in the agricultural sector of
Georgia. Agribusiness environment and the consequences of the
agricultural reforms are evaluated. The factors hindering the
development of agribusiness are revealed and the ways for
overcoming these problems are suggested. SWOT analysis is done in
order to identify the needs of agribusiness. The needs of agribusiness
development in Georgia are evaluated by priorities: prevention of
diseases and reduction of the harm caused by these diseases,
accessibility of long-term agricultural loans with low interest rates,
improving qualification of farmers, the level of education and usage
of modern technologies, changes in legislation, accessibility to high
quality agricultural machinery, and the development of infrastructure.
Based on the outcomes of the research, agribusiness development
strategies in Georgia are suggested and appropriate priorities of
economic policy are determined. Conclusions are made and based on
these conclusions, some recommendations are suggested.
Abstract: Many herbal medicinal products are considered
potential anti-hypercholesterolemic agents with encouraging safety
profiles, however only a limited amount of clinical research exists to
support their efficacy. The present study was designed to compare the
antihypercholesterolemic and antioxidant activities of the crude
ethanolic extracts of Citrus reticulata fruit peel, Zingiber officinale
rhizome and Sesamum indicum seeds. Forty-five rats were used throughout the experiment which are
extended for four weeks. These were divided into nine groups, five
rats per each group as follows; group 1 was the normal control group
(rats only fed standard normal rat diet), group 2 was the
hypercholesterolemic control group (rats fed only
hypercholesterolemic diet which contained 1% cholesterol plus 10%
saturated animal fat added to the normal rat diet), groups 3 and 4
were fed hypercholesterolemic diet in addition to Citrus reticulata
ethanolic extract at doses of (250mg/kg (group 3) and 500mg/kg
(group 4)) administered daily via oral route, groups 5 and 6 were
given hypercholesterolemic diet in addition to Zingiber officinale
ethanolic extract at doses of (250mg/kg (group 5) and 500mg/kg
(group 6)) daily through oral route, groups 7 and 8 fed on
hypercholesterolemic diet in addition to Sesamum indicum ethanolic
extract at doses of (250mg/kg (group 7) and 500mg/kg (group 8))
daily orally; and group 9 rats were given hypercholesterolemic diet in
addition to atorvastatin (0.18mg/kg) daily via oral route as a standard
reference antihypercholesterolemic drug. Blood samples from all
groups were drawn from the retro-orbital venous plexus four weeks
following treatment after overnight fasting and the lipid profile (total
cholesterol (TC), high density lipoprotein-cholesterol (HDL-C), low
density lipoprotein-cholesterol (LDL-C) and triglyceride levels) were
measured and the risk ratio (TC/HDL-C) was assessed. The
antioxidant activity of the three plants extracts was determined using
DPPH free-radical antioxidant assay. Results of in vivo and in vitro
antihypercholesterolemic and antioxidant assay respectively, revealed
that the three extracts possess comparable antioxidant and
antihypercholesterolemic activities.