Abstract: Cements, which are intrinsically brittle materials, can
exhibit a degree of pseudo-ductility when reinforced with a sufficient
volume fraction of a fibrous phase. This class of materials, called
Engineered Cement Composites (ECC) has the potential to be used in
future tunneling applications where a level of pseudo-ductility is
required to avoid brittle failures. However uncertainties remain
regarding mechanical performance. Previous work has focused on
comparatively thin specimens; however for future civil engineering
applications, it is imperative that the behavior in tension of thicker
specimens is understood. In the present work, specimens containing
cement powder and admixtures have been manufactured following
two different processes and tested in tension. Multiple matrix
cracking has been observed during tensile testing, leading to a
“strain-hardening" behavior, confirming the possible suitability of
ECC material when used as thick sections (greater than 50mm) in
tunneling applications.
Abstract: A considerable amount of energy is consumed during
transmission and reception of messages in a wireless mesh network
(WMN). Reducing per-node transmission power would greatly
increase the network lifetime via power conservation in addition to
increasing the network capacity via better spatial bandwidth reuse. In
this work, the problem of topology control in a hybrid WMN of
heterogeneous wireless devices with varying maximum transmission
ranges is considered. A localized distributed topology control
algorithm is presented which calculates the optimal transmission
power so that (1) network connectivity is maintained (2) node
transmission power is reduced to cover only the nearest neighbours
(3) networks lifetime is extended. Simulations and analysis of results
are carried out in the NS-2 environment to demonstrate the
correctness and effectiveness of the proposed algorithm.
Abstract: Linear induction motors are used in various industries
but they have some specific phenomena which are the causes for
some problems. The most important phenomenon is called end effect.
End effect decreases efficiency, power factor and output force and
unbalances the phase currents. This phenomenon is more important
in medium and high speeds machines. In this paper a factor, EEF , is
obtained by an accurate equivalent circuit model, to determine the
end effect intensity. In this way, all of effective design parameters on
end effect is described. Accuracy of this equivalent circuit model is
evaluated by two dimensional finite-element analysis using ANSYS.
The results show the accuracy of the equivalent circuit model.
Abstract: The typical coupled-tanks process that is TITO
plant has the difficulty in controller design because changing
of system dynamics and interacting of process. This paper
presents design methodology of auto-adjustable PI controller
using MRAC technique. The proposed method can adjust the
controller parameters in response to changes in plant and
disturbance real time by referring to the reference model that
specifies properties of the desired control system.
Abstract: The possible therapeutic effect of cannabidiol, the major non-psychotropic Cannabis constituent, was investigated against acute hepatotoxicity induced by a single oral dose of acetaminophen (500mg/kg) in mice. Cannabidiol (two intraperitoneal injections, 5mg/kg, each) was given 1 hour and 12 hours following acetaminophen administration. Acetaminophen administration caused significant elevations of serum alanine aminotransferase, and hepatic malondialdehyde, and nitric oxide levels, and a significant decrease in hepatic reduced glutathione. Cannabidiol significantly attenuated the deterioration in the measured biochemical parameters resulted from acetaminophen administration. Also, histopathological examination showed that cannabidiol markedly attenuated ameliorated acetaminophen-induced liver tissue damage. These results emphasize that cannabidiol represents a potential therapeutic option to protect against acetaminophen hepartotoxicity which is a common clinical problem.
Abstract: The distillation process in the general sense is a
relatively simple technique from the standpoints of its principles.
When dedicating distillation to water treatment and specifically
producing fresh water from sea, ocean and/ briny waters it is
interesting to notice that distillation has no limitations or domains of
applicability regarding the nature or the type of the feedstock water.
This is not the case however for other techniques that are
technologically quite complex, necessitate bigger capital investments
and are limited in their usability. In a previous paper we have
explored some of the effects of temperature on yield. In this paper,
we continue building onto that knowledge base and focus on the
effects of several additional engineering and design variables on
productivity.
Abstract: In order to be able to automatically differentiate
between two modes of permanent flow of a liquid simulating blood,
it was imperative to put together a data bank. Thus, the acquisition of
the various amplitude spectra of the Doppler signal of this liquid in
laminar flow and other spectra in turbulent flow enabled us to
establish an automatic difference between the two modes. According
to the number of parameters and their nature, a comparative study
allowed us to choose the best classifier.
Abstract: This paper investigates several factors affecting the
cost of capital for listed Romanian companies. Although there is a
large amount of literature investigating the drivers of the cost of
capital internationally, there is currently little evidence from
emergent markets. Based on a sample of 19 Romanian listed
companies followed by financial analysts for the years 2008-2010,
according to Thomson Reuters- I/B/E/S data base, the paper confirms
the international trends, showing that size, corporate governance
policies, and growth are negatively correlated with the cost of capital.
Abstract: This paper presents data annotation models at
five levels of granularity (database, relation, column, tuple, and cell) of relational data to address the problem of unsuitability of most relational databases to express annotations. These models
do not require any structural and schematic changes to the
underlying database. These models are also flexible, extensible,
customizable, database-neutral, and platform-independent. This paper also presents an SQL-like query language, named Annotation Query Language (AnQL), to query annotation documents. AnQL is simple to understand and exploits the already-existent wide knowledge and skill set of SQL.
Abstract: This article explores the self-identity of the Kazakh
people by way of identifying the roots of self-understanding in
Kazakh culture. Unfortunately, Western methods of ethno
psychology cannot fully capture what is unique about identity in
Kazakh culture. Although Kazakhstan is the ninth largest country in
terms of geographical space, Kazakh cultural identity is not wellknown
in the West. In this article we offer an account of the national
psychological features of the Kazakh people, in order to reveal the
spiritual, mental, ethical dimensions of modern Kazakhs. These
factors play a central role in the revival of forms of identity that are
central to the Kazakh people.
Abstract: A simple analytical model has been developed to
optimize biasing conditions for obtaining maximum linearity among
lattice-matched, pseudomorphic and metamorphic HEMT types as
well as enhancement and depletion HEMT modes. A nonlinear
current-voltage model has been simulated based on extracted data to
study and select the most appropriate type and mode of HEMT in
terms of a given gate-source biasing voltage within the device so as
to employ the circuit for the highest possible output current or
voltage linear swing. Simulation results can be used as a basis for the
selection of optimum gate-source biasing voltage for a given type
and mode of HEMT with regard to a circuit design. The
consequences can also be a criterion for choosing the optimum type
or mode of HEMT for a predetermined biasing condition.
Abstract: We investigate nonfactorizable contributions to
D → ¤Ç¤Ç decay modes. We perform isospin analysis of the
nonfactorizable contributions to these decays. Obtaining the
factorizable contributions from spectator-quark diagrams using
= 3 C N , we determine nonfactorizable amplitudes for these decays
and predict their branching ratios.
Abstract: Accurate demand forecasting is one of the most key
issues in inventory management of spare parts. The problem of
modeling future consumption becomes especially difficult for lumpy
patterns, which characterized by intervals in which there is no
demand and, periods with actual demand occurrences with large
variation in demand levels. However, many of the forecasting
methods may perform poorly when demand for an item is lumpy.
In this study based on the characteristic of lumpy demand patterns
of spare parts a hybrid forecasting approach has been developed,
which use a multi-layered perceptron neural network and a
traditional recursive method for forecasting future demands. In the
described approach the multi-layered perceptron are adapted to
forecast occurrences of non-zero demands, and then a conventional
recursive method is used to estimate the quantity of non-zero
demands. In order to evaluate the performance of the proposed
approach, their forecasts were compared to those obtained by using
Syntetos & Boylan approximation, recently employed multi-layered
perceptron neural network, generalized regression neural network
and elman recurrent neural network in this area. The models were
applied to forecast future demand of spare parts of Arak
Petrochemical Company in Iran, using 30 types of real data sets. The
results indicate that the forecasts obtained by using our proposed
mode are superior to those obtained by using other methods.
Abstract: Binary Decision Diagrams (BDDs) are useful data
structures for symbolic Boolean manipulations. BDDs are used in
many tasks in VLSI/CAD, such as equivalence checking, property
checking, logic synthesis, and false paths. In this paper we describe a
new approach for the realization of a BDD package. To perform
manipulations of Boolean functions, the proposed approach does not
depend on the recursive synthesis operation of the IF-Then-Else
(ITE). Instead of using the ITE operation, the basic synthesis
algorithm is done using Boolean NOR operation.
Abstract: The demands of taller structures are becoming imperative almost everywhere in the world in addition to the challenges of material and labor cost, project time line etc. This paper conducted a study keeping in view the challenging nature of high-rise construction with no generic rules for deflection minimizations and frequency control. The effects of cyclonic wind and provision of outriggers on 28-storey, 42-storey and 57-storey are examined in this paper and certain conclusions are made which would pave way for researchers to conduct further study in this particular area of civil engineering. The results show that plan dimensions have vital impacts on structural heights. Increase of height while keeping the plan dimensions same, leads to the reduction in the lateral rigidity. To achieve required stiffness increase of bracings sizes as well as introduction of additional lateral resisting system such as belt truss and outriggers is required.
Abstract: Com Poisson distribution is capable of modeling the count responses irrespective of their mean variance relation and the parameters of this distribution when fitted to a simple cross sectional data can be efficiently estimated using maximum likelihood (ML) method. In the regression setup, however, ML estimation of the parameters of the Com Poisson based generalized linear model is computationally intensive. In this paper, we propose to use quasilikelihood (QL) approach to estimate the effect of the covariates on the Com Poisson counts and investigate the performance of this method with respect to the ML method. QL estimates are consistent and almost as efficient as ML estimates. The simulation studies show that the efficiency loss in the estimation of all the parameters using QL approach as compared to ML approach is quite negligible, whereas QL approach is lesser involving than ML approach.
Abstract: The study was designed to evaluate the use of low
concentrations of separan flocculent (Less than 3 ppm) on
physicochemical properties of sugar cane juice. Colour, pH, purity,
turbidity, pol, brix, reducing sugars tannins and polyphenols of
crushed cane (green and burned) juice, mixed juice and clarified
juice were studied. The results showed that pol, brix, reducing sugar
and turbidity are higher in crushed cane juice. Clarified burned juice
had low turbidity, reducing sugars, pol and brix but had significantly
lower pH, purity and colour when compared to crushed juice.
Polyphenols of the crushed juice (1.19%) decreased significantly in
the clarified juice to 0.006%. Addition of separan at a concentration
of 0.015 ppm reduced significantly colour, polyphenols and tannins
and reducing sugar compared to the control.
Abstract: In this paper the effects of top management commitment on knowledge management activities has been analyzed. This research has been conducted as a case study in an academic environment. The data collection was carried out in the form of semi-structured interview with an interview guide. This study shows the effects of knowledge management strategic plan developing in academia strategic plan on knowledge management success. This paper shows the importance top management commitment factors including strategic plan, communication, and training on knowledge management success in academia. In particular the most important role of Strategic planning in knowledge management success is clarified. This study explores one of the necessary organizational infrastructures of successful implementation of knowledge management. The idea of this research could be applied in the other context especially in the industrial organizations.
Abstract: The paper presents a novel method for the 3D shaping
of different materials using a high-pressure abrasive water jet and a
flat target image. For steering movement process of the jet a principle
similar to raster image way of record and readout was used.
However, respective colors of pixel of such a bitmap are connected
with adequate jet feed rate that causes erosion of material with
adequate depth. Thanks to that innovation, one can observe spatial
imaging of the object. Theoretical basis as well as spatial model of
material shaping and experimental stand including steering program
are presented in. There are also presented methodic and some
experimental erosion results as well as practical example of object-s
bas-relief made of metal.
Abstract: Fuzzy logic approach is used in this study to predict
the tractive performance in terms of traction force, and motion
resistance for an intelligent air cushion track vehicle while it operates
in the swamp peat. The system is effective to control the intelligent
air –cushion system with measuring the vehicle traction force (TF),
motion resistance (MR), cushion clearance height (CH) and cushion
pressure (CP). Sinkage measuring sensor, magnetic switch, pressure
sensor, micro controller, control valves and battery are incorporated
with the Fuzzy logic system (FLS) to investigate experimentally the
TF, MR, CH, and CP. In this study, a comparison for tractive
performance of an intelligent air cushion track vehicle has been
performed with the results obtained from the predicted values of FLS
and experimental actual values. The mean relative error of actual and
predicted values from the FLS model on traction force, and total
motion resistance are found as 5.58 %, and 6.78 % respectively. For
all parameters, the relative error of predicted values are found to be
less than the acceptable limits. The goodness of fit of the prediction
values from the FLS model on TF, and MR are found as 0.90, and
0.98 respectively.