Abstract: This paper deals with use of pond ash and RBI Grade 81 for improvement in CBR values of clayey soil and grade-III materials used for base course of flexible pavement. The pond ash is a thermal power plant waste and RBI Grade 81 is chemical soil stabilizer. The geotechnical properties like Maximum Dry Density (MDD), Optimum Moisture Content (OMC), Unconfined Compressive Strength (UCS), CBR value and Differential Free Swell (DFS) index of soil are tested in the laboratory for different mixes of soil, pond ash and RBI Grade 81 for different proportions. The mixes of grade-III material, pond ash and RBI Grade 81 tested for CBR test. From the study it is found that the geotechnical properties of clayey soil are improved significantly, if pond ash added with RBI Grade 81. The optimum mix recommended for subgrade is soil: pond ash: RBI Grade 81 in proportions of 76:20:4. The CBR value of grade-III base course treated with 20% pond ash and 4% RBI Grade 81 is increased by 125.93% as compared to untreated grade-III base course.
Abstract: The coal utilization in thermal power plants in Malaysia has increased significantly which produces an enormous amount of coal combustion by-product (CCBP) or coal ash and poses severe disposal problem. As each coal ash is distinct, this study presents the geochemistry of the coal ash, in particular fly ash, produced from the combustion of local coal from Kuching Sarawak, Malaysia. The geochemical composition of the ash showed a high amount of silica, alumina, iron oxides and alkalies which was found to be a convenient starting material for the hydrothermal synthesis of zeolites with the higher Na2O percentage being a positive factor for its alkaline activation; while the mineral phases are mainly quartz, mullite, calcium oxide, silica, and iron oxide hydrate. The geochemical changes upon alkali activation that can be predicted in a similar type of ash have been described in this paper. The result shows that this particular ash has a good potential for a high value industrial product like zeolites upon alkali activation.
Abstract: This paper presents quantitative component criticality importance indices applicable for identifying and ranking critical components in the phase of thermal power plants design. Identifying critical components for power plant reliability provides one important input to decision-making and guidance throughout the development project. The study of components criticality importance indices to several characteristic structural schemes of conventional thermal power plant is presented and discussed.
Abstract: Fly ash is a waste material of coal firing thermal
plants that is released from thermal power plants. It was defined as
very fine particles that are drifted upward which are taken up by the
flue gases. The emerging amount of fly ash in the world is
approximately 600 million tons per year. In our country, it is
expected that will be occurred 50 million tons of waste ash per year
until 2020. The fly ashes can be evaluated by using as adsorbent
material. The purpose of this study is to investigate the possibility of
use of various fly ashes (Tuncbilek, Catalagzi, Orhaneli) like lowcost
adsorbents for heavy metal adsorption. First of all, fly ashes
were characterized. For this purpose; analyses such as XRD, XRF,
SEM and FT-IR were performed.
Abstract: In this paper presents the mathematical model of
hydrothermal processes in thermal power plant with different wind
direction scenarios in the water reservoir, which is solved by the
Navier - Stokes and temperature equations for an incompressible
fluid in a stratified medium. Numerical algorithm based on the
method of splitting by physical parameters. Three dimensional
Poisson equation is solved with Fourier method by combination of
tridiagonal matrix method (Thomas algorithm).
Abstract: The present study was conducted to investigate the
response of plants exposed to lignite-based thermal power plant
emission. For this purpose, five plant species were collected from 1.0
km distance (polluted site) and control plants were collected from
20.0 km distance (control site) to thermal power plant. The common
tree species Cassia siamea Lamk., Polyalthia longifolia. Sonn,
Acacia longifolia (Andrews) Wild., Azadirachta indica A.Juss, Ficus
religiosa L. were selected as test plants. Photosynthetic pigments
changes (chlorophyll a, chlorophyll b and carotenoids) and rubisco
enzyme modifications were studied. Reduction was observed in the
photosynthetic pigments of plants growing in polluted site and also
large sub unit of the rubisco enzyme was degraded in Azadirachta
indica A. Juss collected from polluted site.
Abstract: The study area receives a wide variety of wastes
generated by municipalities and the industries like paints and
pigments, metal processing industries, thermal power plants electroprocessing
industries etc. The Physico-chemical and structural
investigation of water from river Pandu indicated high level of
chlorides and calcium which made the water unsuitable for human
use. Algae like Cyclotella fumida, Asterionella Formosa,
Cladophora glomerata, Pediastrum simplex, Scenedesmus bijuga,
Cladophora glomerata were the dominant pollution tolerant species
recorded under these conditions. The sensitive and less abundant
species of algae included Spirogyra sps., Merismopedia sps. The
predominance colonies of Zygnema sps, Phormidium sps,
Mycrocystis aeruginosa, Merismopedia minima, Pandorina morum,
seems to correlate with high organic contents of Pandu river water.
This study assumes significance as some algae can be used as
bioindicators of water pollution and algal floral of a municipal drain
carrying waste effluents from industrial area Kanpur and discharge
them into the river Pandu flowing onto southern outskirts of Kanpur
city.
Abstract: IMCS is Integrated Monitoring and Control System for
thermal power plant. This system consists of mainly two parts; controllers and OIS (Operator Interface System). These two parts are
connected by Ethernet-based communication. The controller side of communication is managed by CNet module and OIS side is managed
by data server of OIS. CNet module sends the data of controller to data
server and receives commend data from data server. To minimizes or
balance the load of data server, this module buffers data created by controller at every cycle and send buffered data to data server on request of data server. For multiple data server, this module manages
the connection line with each data server and response for each request
from multiple data server. CNet module is included in each controller
of redundant system. When controller fail-over happens on redundant system, this module can provide data of controller to data sever
without loss. This paper presents three main features – separation of get task, usage of ring buffer and monitoring communication status –of CNet module to carry out these functions.
Abstract: The objectif of the present work is to determinate the
potential of the solar parabolic trough collector (PTC) for use in the
design of a solar thermal power plant in Algeria. The study is based
on a mathematical modeling of the PTC. Heat balance has been
established respectively on the heat transfer fluid (HTF), the absorber
tube and the glass envelop using the principle of energy conservation
at each surface of the HCE cross-sectionn. The modified Euler
method is used to solve the obtained differential equations. At first
the results for typical days of two seasons the thermal behavior of the
HTF, the absorber and the envelope are obtained. Then to determine
the thermal performances of the heat transfer fluid, different oils are
considered and their temperature and heat gain evolutions compared.
Abstract: Understanding of how and where NOx formation
occurs in industrial burner is very important for efficient and clean
operation of utility burners. Also the importance of this problem is
mainly due to its relation to the pollutants produced by more burners
used widely of gas turbine in thermal power plants and glass and steel
industry.
In this article, a numerical model of an industrial burner operating
in MILD combustion is validated with experimental data.. Then
influence of air flow rate and air temperature on combustor
temperature profiles and NOX product are investigated. In order to
modification this study reports on the effects of fuel and air dilution
(with inert gases H2O, CO2, N2), and also influence of lean-premixed
of fuel, on the temperature profiles and NOX emission.
Conservation equations of mass, momentum and energy, and
transport equations of species concentrations, turbulence, combustion
and radiation modeling in addition to NO modeling equations were
solved together to present temperature and NO distribution inside the
burner.
The results shows that dilution, cause to a reduction in value of
temperature and NOX emission, and suppresses any flame
propagation inside the furnace and made the flame inside the furnace
invisible. Dilution with H2O rather than N2 and CO2 decreases further
the value of the NOX. Also with raise of lean-premix level, local
temperature of burner and the value of NOX product are decreases
because of premixing prevents local “hot spots" within the combustor
volume that can lead to significant NOx formation. Also leanpremixing
of fuel with air cause to amount of air in reaction zone is
reach more than amount that supplied as is actually needed to burn
the fuel and this act lead to limiting NOx formation
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: A geothermal power plant multiple simulator for
operators training is presented. The simulator is designed to be
installed in a wireless local area network and has a capacity to train
one to six operators simultaneously, each one with an independent
simulation session. The sessions must be supervised only by one
instructor. The main parts of this multiple simulator are: instructor
and operator-s stations. On the instructor station, the instructor
controls the simulation sessions, establishes training exercises and
supervises each power plant operator in individual way. This station
is hosted in a Main Personal Computer (NS) and its main functions
are: to set initial conditions, snapshots, malfunctions or faults,
monitoring trends, and process and soft-panel diagrams. On the other
hand the operators carry out their actions over the power plant
simulated on the operator-s stations; each one is also hosted in a PC.
The main software of instructor and operator-s stations are executed
on the same NS and displayed in PCs through graphical Interactive
Process Diagrams (IDP). The geothermal multiple simulator has been
installed in the Geothermal Simulation Training Center (GSTC) of
the Comisi├│n Federal de Electricidad, (Federal Commission of
Electricity, CFE), Mexico, and is being utilized as a part of the
training courses for geothermal power plant operators.
Abstract: Typically thermal power plants are located near to
surface coal mines that produce huge amount of fly ash as a waste
byproduct. Disposal of fly ash causes significant economic and
environmental problems. Now-a-days, research is going on for bulk
utilization of fly ash. In order to increase its percentage utilization, an
investigation was carried out to evaluate its potential for haul road
construction. This paper presents the laboratory California bearing
ratio (CBR) tests and evaluates the effect of lime on CBR behavior of
fly ash - mine overburden mixes. Tests were performed with different
percentages of lime (2%, 3%, 6%, and 9%). The results show that the
increase in bearing ratio of fly ash-overburden mixes was achieved
by lime treatment. Scanning electron microscopy (SEM) analyses
were conducted on 28 days cured specimens. The SEM study showed
that the bearing ratio development is related to the microstructural
development.
Abstract: Coal will continue to be the predominant source of
global energy for coming several decades. The huge generation of fly
ash (FA) from combustion of coal in thermal power plants (TPPs) is
apprehended to pose the concerns of its disposal and utilization. FA
application based on its typical characteristics as soil ameliorant for
agriculture and forestry is the potential area, and hence the global
attempt. The inferences drawn suffer from the variations of ash
characteristics, soil types, and agro-climatic conditions; thereby
correlating the effects of ash between various plant species and soil
types is difficult. Indian FAs have low bulk density, high water
holding capacity and porosity, rich silt-sized particles, alkaline
nature, negligible solubility, and reasonable plant nutrients. Findings
of the demonstrations trials for more than two decades from lab/pot
to field scale long-term experiments are developed as FA soil
amendment technology (FASAT) by Central Institute of Mining and
Fuel Research (CIMFR), Dhanbad. Performance of different crops
and plant species in cultivable and problematic soils, are
encouraging, eco-friendly, and being adopted by the farmers. FA
application includes ash alone and in combination with
inorganic/organic amendments; combination treatments including
bio-solids perform better than FA alone. Optimum dose being up to
100 t/ha for cultivable land and up to/ or above 200 t/ha of FA for
waste/degraded land/mine refuse, depending on the characteristics of
ash and soil. The elemental toxicity in Indian FA is usually not of
much concern owing to alkaline ashes, oxide forms of elements, and
elemental concentration within the threshold limits for soil
application. Combating toxicity, if any, is possible through
combination treatments with organic materials and phytoremediation.
Government initiatives through extension programme
involving farmers and ash generating organizations need to be
accelerated
Abstract: In present study, two kinds of thermal power plant ashes; one the fly ash and the other waste ash are mixed with adhesive tragacanth and cement to produce new composite materials. 48 new samples are produced by varying the percentages of the fly ash, waste ash, cement and tragacanth. The new samples are subjected to some tests to find out their properties such as thermal conductivity, compressive strength, tensile strength and sucking capability of water. It is found that; the thermal conductivity decreases with increasing amount of tragacanth in the mixture. The compressive, tensile strength increases when the rate of tragacanth is up to 1%, whilst as the amount of tragacanth increases up to 1.5%, the compressive, tensile strength decreases slightly. The rate of water absorption of samples was more than 30%. From this result, it is concluded that these materials can not be used as external plaster or internal plaster material that faces to water. They can be used in internal plaster unless touching water and they can be used as cover plaster under roof and riprap material in sandwich panels. It is also found that, these materials can be cut with saw, drilled with screw and painted with any kind of paint.