Abstract: This work deals with the synthesis and the determination of some surface properties of a new anionic surfactant belonging to sulfonamide derivatives. The interest in this new surfactant is that its behavior in aqueous solution is interesting both from a fundamental and a practice point of view. Indeed, it is well known that this kind of surfactant leads to the formation of bilayer structures, and the microstructures obtained have applications in various fields, ranging from cosmetics to detergents, to biological systems such as cell membranes and bioreactors. The surfactant synthesized from pure n-alkane by photosulfochlorination and derivatized using N-ethanol amine is a mixture of position isomers. These compounds have been analyzed by Gas Chromatography coupled to Mass Spectrometry by Electron Impact mode (GC -MS/IE), and IR. The surface tension measurements were carried out, leading to the determination of the critical micelle concentration (CMC), surface excess and the area occupied per molecule at the interface. The foaming power has also been determined by Bartsch method, and the results have been compared to those of commercial surfactants. The stability of the foam formed has also been evaluated. These compounds show good foaming power characterized in most cases by dry foam.
Abstract: There are various sources of energies available
worldwide and among them, crude oil plays a vital role. Oil recovery
is achieved using conventional primary and secondary recovery
methods. In-order to recover the remaining residual oil, technologies
like Enhanced Oil Recovery (EOR) are utilized which is also known
as tertiary recovery. Among EOR, Microbial enhanced oil recovery
(MEOR) is a technique which enables the improvement of oil
recovery by injection of bio-surfactant produced by microorganisms.
Bio-surfactant can retrieve unrecoverable oil from the cap rock which
is held by high capillary force. Bio-surfactant is a surface active agent
which can reduce the interfacial tension and reduce viscosity of oil
and thereby oil can be recovered to the surface as the mobility of the
oil is increased. Research in this area has shown promising results
besides the method is echo-friendly and cost effective compared with
other EOR techniques. In our research, on laboratory scale we
produced bio-surfactant using the strain Pseudomonas putida (MTCC
2467) and injected into designed simple sand packed column which
resembles actual petroleum reservoir. The experiment was conducted
in order to determine the efficiency of produced bio-surfactant in oil
recovery. The column was made of plastic material with 10 cm in
length. The diameter was 2.5 cm. The column was packed with fine
sand material. Sand was saturated with brine initially followed by oil
saturation. Water flooding followed by bio-surfactant injection was
done to determine the amount of oil recovered. Further, the injection
of bio-surfactant volume was varied and checked how effectively oil
recovery can be achieved. A comparative study was also done by
injecting Triton X 100 which is one of the chemical surfactant. Since,
bio-surfactant reduced surface and interfacial tension oil can be easily
recovered from the porous sand packed column.
Abstract: This work concerns on experimentally investigation
of surfactant flooding in fractured porous media. In this study a series
of water and surfactant injection processes were performed on
micromodels initially saturated with a heavy crude oil. Eight
fractured glass micromodels were used to illustrate effects of
surfactant types and concentrations on oil recovery efficiency in
presence of fractures with different properties i.e. fracture
orientation, length and number of fractures. Two different
surfactants with different concentrations were tested. The results
showed that surfactant flooding would be more efficient by using
SDS surfactant aqueous solution and also by locating injection well
in a proper position respect to fracture properties. This study
demonstrates different physical and chemical conditions that affect
the efficiency of this method of enhanced oil recovery.
Abstract: Calcite aCalcite and aragonite are the two common
polymorphs of CaCO3 observed as biominerals. It is universal that
the sea water contents a high Mg2+ (50mM) relative to Ca2+ (10mM).
In vivo crystallization, Mg2+ inhibits calcite formation. For this
reason, stony corals skeleton may be formed only aragonite crystals
in the biocalcification. It is special in case of soft corals of which
formed only calcite crystal; however, this interesting phenomenon,
still uncharacterized in the marine environment, has been explored in
this study using newly purified cell-free proteins isolated from the
endoskeletal sclerites of soft coral. By recording the decline of pH in
vitro, the control of CaCO3 nucleation and crystal growth by the cellfree
proteins was revealed. Using Atomic Force Microscope, here we
find that these endoskeletal cell-free proteins significantly design the
morphological shape in the molecular-scale kinetics of crystal
formation and those proteins act as surfactants to promote ion
attachment at calcite steps.nd aragonite are the two common polymorphs of CaCO3 observed as biominerals. It is universal that the sea water contents a high Mg2+ (50mM) relative to Ca2+ (10mM). In vivo crystallization, Mg2+ inhibits calcite formation. For this reason, stony corals skeleton may be formed only aragonite crystals in the biocalcification. It is special in case of soft corals of which formed only calcite crystal; however, this interesting phenomenon, still uncharacterized in the marine environment, has been explored in this study using newly purified cell-free proteins isolated from the endoskeletal sclerites of soft coral. By recording the decline of pH in vitro, the control of CaCO3 nucleation and crystal growth by the cell-free proteins was revealed. Using Atomic Force Microscope, here we find that these endoskeletal cell-free proteins significantly design the morphological shape in the molecular-scale kinetics of crystal formation and those proteins act as surfactants to promote ion attachment at calcite steps. KeywordsBiomineralization, Calcite, Cell-free protein, Soft coral
Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: Most of the drugs used for pharmaceutical purposes
are poorly water-soluble drugs. About 40% of all newly discovered
drugs are lipophilic and the numbers of lipophilic drugs seem to
increase more and more. Drug delivery systems such as
nanoparticles, micelles or liposomes are applied to improve their
solubility and thus their bioavailability. Besides various techniques of
solubilization, oil-in-water emulsions are often used to incorporate
lipophilic drugs into the oil phase. To stabilize emulsions surface
active substances (surfactants) are generally used. An alternative
method to avoid the application of surfactants was of great interest.
One possibility is to develop O/W-emulsion without any addition of
surface active agents or the so called “surfactant-free emulsion or
SFE”. The aim of this study was to develop and characterize SFE as a
drug carrier by varying the production conditions. Lidocaine base
was used as a model drug. The injection method was developed.
Effects of ultrasound as well as of temperature on the properties of
the emulsion were studied. Particle sizes and release were
determined. The long-term stability up to 30 days was performed.
The results showed that the surfactant-free O/W emulsions with
pharmaceutical oil as drug carrier can be produced.
Abstract: One of the most challenges for hard surface cleaning product is to get rid of soap scum, a filmy sticky layer in the bathroom. The deposits of soap scum can be removed by using a proper surfactant solution with chelating agent. Unfortunately, the conventional chelating agent, ethylenediamine tetraacetic acid (EDTA), has low biodegradability, which can be tolerance in water resources and harmful to aquatic animal and microorganism. In this study, two biodegradable chelating agents, ethylenediamine disuccinic acid (EDDS) and glutamic acid diacetic acid (GLDA) were introduced as a replacement of EDTA. The result shows that using GLDA with amphoteric surfactant gave the highest equilibrium solubility of soap scum.
Abstract: Losses of surfactant due to sorption need to be
considered when selecting surfactant doses for soil bioremediation.
The degree of surfactant sorption onto soil depends primarily on the
organic carbon fraction of soil and the chemical nature of the
surfactant. The use of biosurfactants in the control of the
bioavailability of toxicants in soils is an attractive option because of
their biodegradability. In this work biosurfactants were produced
from a cheap raw material, trimming vine shoots, employing
Lactobacillus pentosus. When biosurfactants from L. pentosus was
added to sediments the surface tensión of the water containing the
sediments rapidly increase, the same behaviour was observed with
the chemical surfactant Tween 20; whereas sodyum dodecyl sulphate
(SDS) kept the surface tension of the water around 36 mN/m. It
means, that the behaviour of biosurfactants from L. pentosus is more
similar to non-ionic surfactatns than to anionic surfactants.
Abstract: Nitrogen loss from irrigated cropland, particularly
sandy soils, significantly contributes to nitrate (NO3
-) levels in
surface and groundwaters. Thus, it is of great interest to use
inexpensive natural products that can increase the fertilizer efficiency
and decrease nitrate leaching. In this study, the ability of natural
Iranian zeolite clinoptilolite (Cp) and surfactant modified zeolite
clinoptilolite (SMZ) to remove NH4
+ and NO3
-, respectively, from
aqueous solutions was determined. The feasibility of using Cp and
SMZ as soil amendment to reduce nitrate leaching from soil using
lysimeters was also investigated. Zeolite showed 10.23% to 88.42%
NH4
+ removal efficiency over a wide range of initial NH4
+
concentrations. Nitrate removal efficiency by SMZ was 32.26% to
82.26%. Field study results showed that Cp and SMZ significantly (p
< 0.05) reduced leachate NO3-N concentration compared to control.
There was no significant difference between maximum and mean
leachate NO3-N concentration of SMZ lysimeters and those of Cp
lysimeters.
Abstract: Soy polyol obtained from hydroxylation of soy
epoxide with ethylene glycol were prepared as pre-polyurethane. The
two step process method were applied in the polyurethane synthesis.
The blending of soy polyol with synthetic polyol then simultaneously
carried out to TDI (2,4): MDI (4,4-) (80:20), blowing agent, and
surfactant. Ethylene glycol were not taking part in the polyurethane
synthesis. The inclusion of ethylene glycol were used as a control.
Characterization of polyurethane foam through impact resillience,
indentation deflection, and density can visualize the polyurethane
classifications.
Abstract: Titanium oxide films with different morphologies have for the first time been fabricated through hydrothermal reactions between a titanium substrate and iodine powder in water or ethanol. SEM revealed that iodine supported titanium (Ti-I2) surface shows different morphologies with variable treatment conditions. The mean surface roughness (Ra) was increased in the different groups. Use of surfactant has a role to increase the roughness of the film. The surface roughness was in the range of 0.15 μm-0.42 μm. Furthermore, the electrochemical examinations showed that the Ti-I2 surface fabricated in alcoholic medium has high corrosion resistance than in aqueous medium.
Abstract: Polyurethane foams (PUF) has been prepared from
vegetable; soybean based polyols. They were characterized into
flexible and semi rigid polyurethane foam. This work is directed to
production of flexible polyurethane foams by a process involving the
reaction of mixture of 2,4- and 2,6-Toluene di Isocyanate isomers,
with portion of to blends of soy polyols with petroleum polyol in the
presence of other ingredients such as blowing agents, silicone
surfactants and accelerating agents. Additon of chain extender
improves the property then further decreases the properties on further
addition of the same. The objective of this work was to study the
effect of chain extender and role of phosphoric acid catalyst to the
final properties and correlate the morphology image with mechanical
properties of these foams.
Abstract: The evolution of silica optical fiber strength aged in cetyltrimethylammonium chloride solution (CTAC) has been investigated. If the solution containing surfactants presents appreciable changes in physical and chemical properties at the critical micelle concentration (CMC), a non negligible mechanical behavior fiber change is observed for silica fiber aged in cationic surfactants as CTAC which can lead to optical fiber reliability questioning. The purpose of this work is to study the mechanical behavior of silica coated and naked optical fibers in contact with CTAC solution at different concentrations. Result analysis proves that the immersion in CTAC drastically decreases the fiber strength and specially near the CMC point. Beyond CMC point, a small increase of fiber strength is analyzed and commented.
Abstract: A local wastewater treatment plant (WWTP)
experiencing poor nitrification tracked down high level of
surfactants in the plant-s influent and effluent. The aims of this project were to assess the potential inhibitory effect of surfactants on activated sludge processes. The effect of the
presence of TergitolNP-9, TrigetolNP-7, Trigetol15-S-9,
dodecylbenzene sulphonate (SDBS) and sodium dodecyl
sulfate (SDS) on activated sludge oxygen uptake rate (OUR) and nitrification were assessed. The average concentration of non-ionic and anionic
surfactants in the influent to the local WWTP were 7 and 8.7 mg/L, respectively. Removal of 67% to 90% of the non-ionic and 93-99% of the anionic surfactants tested were measured. All surfactants tested showed inhibitory effects both on OUR
and nitrification. SDS incurred the lowest inhibition whereas
SDBS and NP-9 caused severe inhibition to OUR and
Nitrification. Activated sludge flocs sizes slightly decreased
after 3 hours contact with the surfactant present in the test.
The results obtained indicated that high concentrations of
surfactants are likely to have an adverse effect on the
performance of WWTPs utilizing activated sludge processes.
Abstract: The Marangoni convective instability in a horizontal
fluid layer with the insoluble surfactant and nondeformable free
surface is investigated. The surface tension at the free surface is
linearly dependent on the temperature and concentration gradients.
At the bottom surface, the temperature conditions of uniform
temperature and uniform heat flux are considered. By linear stability
theory, the exact analytical solutions for the steady Marangoni
convection are derived and the marginal curves are plotted. The
effects of surfactant or elasticity number, Lewis number and Biot
number on the marginal Marangoni instability are assessed. The
surfactant concentration gradients and the heat transfer mechanism at
the free surface have stabilizing effects while the Lewis number
destabilizes fluid system. The fluid system with uniform temperature
condition at the bottom boundary is more stable than the fluid layer
that is subjected to uniform heat flux at the bottom boundary.
Abstract: Nanoemulsions are a class of emulsions with a droplet
size in the range of 50–500 nm and have attracted a great deal of
attention in recent years because it is unique characteristics. The
physicochemical properties of nanoemulsion suggests that it can be
successfully used to recover the residual oil which is trapped in the
fine pore of reservoir rock by capillary forces after primary and
secondary recovery. Oil-in-water nanoemulsion which can be formed
by high-energy emulsification techniques using specific surfactants
can reduce oil-water interfacial tension (IFT) by 3-4 orders of
magnitude. The present work is aimed on characterization of oil-inwater
nanoemulsion in terms of its phase behavior, morphological
studies; interfacial energy; ability to reduce the interfacial tension and
understanding the mechanisms of mobilization and displacement of
entrapped oil blobs by lowering interfacial tension both at the
macroscopic and microscopic level. In order to investigate the
efficiency of oil-water nanoemulsion in enhanced oil recovery
(EOR), experiments were performed to characterize the emulsion in
terms of their physicochemical properties and size distribution of the
dispersed oil droplet in water phase. Synthetic mineral oil and a series
of surfactants were used to prepare oil-in-water emulsions.
Characterization of emulsion shows that it follows pseudo-plastic
behaviour and drop size of dispersed oil phase follows lognormal
distribution. Flooding experiments were also carried out in a
sandpack system to evaluate the effectiveness of the nanoemulsion as
displacing fluid for enhanced oil recovery. Substantial additional
recoveries (more than 25% of original oil in place) over conventional
water flooding were obtained in the present investigation.
Abstract: The effect of concentration of reduction agent of
sodium borohydrate (NaBH4) on the properties of silicon
nanoparticles synthesized via microemulsion route is reported. In
this work, the concentration of the silicon tetrachloride (SiCl4) that
served as silicon source with sodium hydroxide (NaOH) and
polyethylene glycol (PEG) as stabilizer and surfactant, respectively,
are keep fixed. Four samples with varied concentration of NaBH4
from 0.05 M to 0.20 M were synthesized. It was found that the lowest
concentration of NaBH4 gave better formation of silicon
nanoparticles.
Abstract: There has been a growing interest in utilizing surfactants in remediation processes to separate the hydrophobic volatile organic compounds (HVOCs) from aqueous solution. One attractive process is cloud point extraction (CPE), which utilizes nonionic surfactants as a separating agent. Since the surfactant cost is a key determination of the economic viability of the process, it is important that the surfactants are recycled and reused. This work aims to study the performance of the co-current vacuum stripping using a packed column for HVOCs removal from contaminated surfactant solution. Six types HVOCs are selected as contaminants. The studied surfactant is the branched secondary alcohol ethoxylates (AEs), Tergitol TMN-6 (C14H30O2). The volatility and the solubility of HVOCs in surfactant system are determined in terms of an apparent Henry’s law constant and a solubilization constant, respectively. Moreover, the HVOCs removal efficiency of vacuum stripping column is assessed in terms of percentage of HVOCs removal and the overall liquid phase volumetric mass transfer coefficient. The apparent Henry’s law constant of benzenz , toluene, and ethyl benzene were 7.00×10-5, 5.38×10-5, 3.35× 10-5 respectively. The solubilization constant of benzene, toluene, and ethyl benzene were 1.71, 2.68, 7.54 respectively. The HVOCs removal for all solute were around 90 percent.
Abstract: Chemical and physical functionalization of multiwalled
carbon nanotubes (MWCNT) has been commonly practiced to
achieve better dispersion of carbon nanotubes (CNTs) in polymer
matrix. This work describes various functionalization methods (acidtreatment,
non-ionic surfactant treatment with TritonX-100),
fabrication of MWCNT/PP nanocomposites via melt blending and
characterization of mechanical properties. Microscopy analysis
(FESEM, TEM, XPS) showed effective purification of MWCNTs
under acid treatment, and better dispersion under both chemical and
physical functionalization techniques combined, in their respective
order. Tensile tests showed increase in tensile strength for the
nanocomposites that contain MWCNTs up to 2 wt%. A decrease in
tensile strength was seen in samples that contain 4 wt% of MWCNTs
for both raw and Triton X-100 functionalized, signifying MWCNT
degradation/rebundling at composition with higher content of
MWCNTs. For the acid-treated MWCNTs, however, the tensile
results showed slight improvement even at 4wt%, indicating effective
dispersion of MWCNTs.